Additional Feature Setup Window, 100 | Telex IP-223 specs

Setup Information

Additional Feature Setup Window

The Additional Feature setup window activates special features enabled by purchasing an option string from Telex. Examples of special features are Kenwood’s Fleetsync and Motorola’s MDC1200 Over-the-Air ANI decoder. For more information contact Telex Sales. Have the unit serial number available when purchasing this option.

NAVIGATION: Clicking Additional Feature displays the Additional Feature Setup window shown in Figure 126.

FIGURE 126. Additional Feature Access

To activate a special feature, do the following:

1.From the links, select Additional Feature. The Additional Feature Setup window appears.

2.In the enter Access Key field, enter the 16-digit option string.

3.Click Submit.

The entries currently displayed on the window are sent to the IP-223 for storage.

4.From the links, select Save to EEPROM. The Save Setup Parameters window appears.

5.Click Save Parameters.

The entries are saved to permanent memory.

100

Image 98

Telex IP-223 technical manual Additional Feature Setup Window, 100, To activate a special feature, do the following

Contents

Model IP-223 Remote Adapter Panel Technical Manual Sales Contents General Gain Setup Save to Eeprom Window Update Firmware Figures Call Type Drop Down Menu iDEN Mode List Tables Page Overview Operating Modes Features Console Mode Connection IP-223 Accessories Part Number Description Front Panel IP-223 SpecificationsTest and Adjustment Points LCD Display Handset JackIC Button Line Button TX LED Back Panel 10/100 Ethernet ConnectorSerial Connector Jumper position Connection type Radio 1 and Radio 2 Line 1 and Line 2 Connectors Power Connection Pin # Signal Cable color Ctcss Overview Multicast Network RequirementsBandwidth Internet Group Management Protocol Igmp Network Performance Jumper Positions To adjust the position of a jumper, do the followingLocal/Radio Connections Installation and Level Settings Line 1 jumpers J3, J9, and J11 TX Audio ConnectionRX Audio Connection Monitor Connection COR Carrier Operated Relay I/O Input/OutputPTT Connection R1 and R2 Relays Tone/Console Operation Wire Jumper SettingsTX Side Settings Digital I/O Cross Mute I/O Level AdjustmentsLocal PTT I/O Supervisory I/O Radio/Line TX Level Line TX Monitor Level Tone and Console Mode onlyGeneral Alignment Radio/Line RX Level Frequency Decoding Ctcss Level Setup Information Setting the IP Address Information Using HyperTerminal Com1 Properties window appears Main HyperTerminal window appears Enter Password for Factory Setup appears Serial port access window shown in appears Close the HyperTerminal program Accessing IP-223 Web Browser Configuration Windows To access the IP-223 web setup windows, do the following Link Description IP-223 Web Setup Windows StandardsLinks Click Save Parameters To permanently save changes, do the followingClick Save to Eeprom Welcome Window To change the name of the IP-223 unit, do the following MAC Address Basic Ethernet Setup WindowSerial Number Field Use Dhcp Server Check Box Packet Delay before Playback FieldQOS Quality of Service Precedence Bits Field Unit IP Address Field Local Computer IP Address 1-10 Fields Routing R To configure the IP-223 for use, do the following Submit Button Handset Sidetone Gain Drop Down Menu General Gain SetupHandset Mic Gain Drop Down Menu Receive Gain Drop Down Menu TX Voice Gain Field Transmit Gain Drop Down MenuCtcss Gain Drop Down Menu Line Number Field Multicast Address Setup WindowEnable via Ethernet Check Box RX Mcast Address Field Line Type Drop Down MenuLine Name Field TX Port Field RX Port FieldTX Mcast Address Field TX Group Port Field Multicast Address Field Enable Check BoxVocoder Type Drop Down Menu Incoming Port Field Outgoing Port FieldName Field Mcast Address Field Port Field Per Line Setup Window Per Line Setup Local, Tone, and Console Modes view Line 1 Button COR Active High check box LAM Enabled Check BoxCOR Enabled Check Box Squelch Tail Delay Field TX Delay FieldRX Delay Field Update Button Relay Group Drop Down Menu Tone Enable Check BoxRelay Drop Down Menu Relay Time ms Field Ctcss Default Check Box Local Mode Only Digital Output Field Local Mode OnlyCtcss Freq Field Local Mode Only System Field Local Mode LAM Level Field LAM Time Field Options Serial Port Mode Drop Down Menu PTT Timeout FieldWire Check Box Parallel Console Check Box Serial Port Drop Down Menu Local Mode Serial Port Params Drop Down Menu Signaling Setup FleetSync Decode Check Box Tone and Local Modes MDC Encode Check Box FleetSync Encode Check Box Local Mode OnlyMDC Decode Check Box Tone and Local Modes Tone Type Drop Down Menu Interdigit Duration Field ANI Suffix FieldDigit Duration Field Pause Duration Field ANI Call Type Drop Down Menu ANI Call Format Field Auto Disconnect Time Field Per Line Setup Window-Phone Mode ConfigurationAuto Answer Field Time Between Clicks Field Mic Click Call Enabled Check BoxNumber of Clicks Field Click Dial String Field Click Dial Timeout Field Relay Closure R1 Ring Check Box Star/Pound Keying Enabled Check Box Rx AGC Enabled Check BoxKeep Alive Digits Enabled Check Box Detect Tones Enabled Check Box Serial Port Mode Drop Down Menu Serial Port Parameters Drop Down Menu Serial Port Params Drop Down Menu Phone Mode FleetSync Decode Check Box MDC Decode Check Box ANI Decoder Field Per Line Setup Window-iDEN Radio Configuration ANI Call Type Drop Down Menu Per Line Setup iDEN Radio Mode view Jump To Entry Drop Down Menu Call Type Drop Down Menu IDEN Number Field Per Line Setup iDEN Mode view F1 Last Call Check Box iDEN Mode only PTT Timeout Field Per line Setup Window-Tetra Radio Configuration Per Line Setup Tetra Mode view Relay Drop Down Menu Type Drop Down Menu ISSI/GSSI Number Field TX Delay Field LAM Level Field PTT Timeout Field Save to Eeprom Window Reset IP-223 ButtonClick Reset IP-223 Save Parameters Button User System Account Account Setup WindowAdmin System Account New Password Field Enable Check BoxPassword Field Username Display Column Edit Button Confirm Password FieldTo enable the user account, do the following Save Button Delete Button Reset System Parameters ButtonEdit System Accounts Window Add New User Button Password can be 4-16 alpha-numeric characters in length Username Field Add New User WindowChoose a Username Basic Ethernet & Multicast Setup Check Box Additional Feature Check BoxAccount Setup Check Box CRP Setup & PIN Table Check Box Cancel Button Tone Freq & Durations Check Box Edit Created Account-Account Setup Edit Created Accounts Window 100 Additional Feature Setup WindowTo activate a special feature, do the following Clone Console Window 101 Crosspatch Setup Window 102 103 Jump To Entry Drop Down Menu and Go Button 104RCP Tables Delete String Field Mode Drop Down Menu105 Phone Field Dial option only Command Buttons 106 To define the crosspatch parameters, do the following 107Next 10 Button Submit CRP PIN Table Window 108 Entry Field PIN Enable Check Box109 PIN Field Next 30 Entries Button 110Prev 30 Entries Button To define crosspatch PIN numbers, do the following Pass Change Window 111 Monitor Frequency Field Tone Frequency & Durations Window112 113 Function Tone Magnitude Field 114Function Tone Duration Field FTone 1-16 Frequency Fields 115 116 117 Update FirmwareInstall TSM Confirm Installation 118 119 Download Telex Firmware 120 Update Firmware Tool WindowFirmware File Info Group Box Upload VoIP Hardware Firmware Login Group Box121 Firmware Update Tool- Success Messages Click Close 122 Connector Description ConnectorsAdjustments Signal Line Test point PCB 750743 or PCB 750630 revision F Jumper Settings124 PCB 750743 or PCB 750630 revision C, D, E, and F Jumper Locations 125 126 Additional Resources 127 Relm RM Series Radios to 223 Series Adaptor Panels 128 Relm GMH Radios to IP-223 Adaptor Panels 129 130 Tone Freq Number Ctcss Tone Frequency Table131 132 Digital Output Values Digital Output Table133 134 Tone Number Code Digit Tone Frequency Table135 European Tone Frequencies in Hz Motorola 136 137