Signaling Setup | Telex IP-223 specs

Per Line Setup Window—Local, Tone, and Console Mode Configuration

FIGURE 102. Per Line Setup - Local, Tone, and Console Mode (view 3)

Signaling Setup

The Signaling Setup section is used to setup encode, decode, tone type and digits pause and duration.

IMPORTANT: The FleetSync features in this section are optional IP-223 accessories. See “IP-223 Accessories” on page 15 for part numbers.

FleetSync Decode Check Box (Tone and Local Modes)

The FleetSync Decode check box is used to enable the line for radio IDs with FleetSync ANI capabilities to decode their alias, ID numbers, and messages on Telex consoles within the system. If selected, Kenwood FleetSync's over-the-air ANI is enabled and the ANI number or name is decoded via the ANI lookup tables and displayed on Telex IP based consoles.

65

Image 63

Telex IP-223 technical manual Signaling Setup, FleetSync Decode Check Box Tone and Local Modes

Contents

Model IP-223 Remote Adapter Panel Technical Manual Sales Contents General Gain Setup Save to Eeprom Window Update Firmware Figures Call Type Drop Down Menu iDEN Mode List Tables Page Operating Modes Overview Console Mode Connection Features Part Number Description IP-223 Accessories IP-223 Specifications Test and Adjustment PointsFront Panel Handset Jack IC ButtonLCD Display TX LED Line Button Jumper position Connection type 10/100 Ethernet ConnectorSerial Connector Back Panel Power Connection Radio 1 and Radio 2 Line 1 and Line 2 Connectors Ctcss Pin # Signal Cable color Overview Network Requirements BandwidthMulticast Network Performance Internet Group Management Protocol Igmp To adjust the position of a jumper, do the following Local/Radio ConnectionsJumper Positions Installation and Level Settings TX Audio Connection RX Audio ConnectionLine 1 jumpers J3, J9, and J11 R1 and R2 Relays COR Carrier Operated Relay I/O Input/OutputPTT Connection Monitor Connection Digital I/O Wire Jumper SettingsTX Side Settings Tone/Console Operation Supervisory I/O Level AdjustmentsLocal PTT I/O Cross Mute I/O Radio/Line RX Level Line TX Monitor Level Tone and Console Mode onlyGeneral Alignment Radio/Line TX Level Ctcss Level Frequency Decoding Setting the IP Address Information Setup Information Com1 Properties window appears Using HyperTerminal Main HyperTerminal window appears Enter Password for Factory Setup appears Serial port access window shown in appears Close the HyperTerminal program To access the IP-223 web setup windows, do the following Accessing IP-223 Web Browser Configuration Windows IP-223 Web Setup Windows Standards LinksLink Description To permanently save changes, do the following Click Save to EepromClick Save Parameters To change the name of the IP-223 unit, do the following Welcome Window Basic Ethernet Setup Window Serial Number FieldMAC Address Unit IP Address Field Packet Delay before Playback FieldQOS Quality of Service Precedence Bits Field Use Dhcp Server Check Box Routing R Local Computer IP Address 1-10 Fields Submit Button To configure the IP-223 for use, do the following Receive Gain Drop Down Menu General Gain SetupHandset Mic Gain Drop Down Menu Handset Sidetone Gain Drop Down Menu Transmit Gain Drop Down Menu Ctcss Gain Drop Down MenuTX Voice Gain Field Multicast Address Setup Window Enable via Ethernet Check BoxLine Number Field Line Type Drop Down Menu Line Name FieldRX Mcast Address Field TX Group Port Field RX Port FieldTX Mcast Address Field TX Port Field Enable Check Box Vocoder Type Drop Down MenuMulticast Address Field Outgoing Port Field Name FieldIncoming Port Field Port Field Mcast Address Field Per Line Setup Window Line 1 Button Per Line Setup Local, Tone, and Console Modes view LAM Enabled Check Box COR Enabled Check BoxCOR Active High check box Update Button TX Delay FieldRX Delay Field Squelch Tail Delay Field Relay Time ms Field Tone Enable Check BoxRelay Drop Down Menu Relay Group Drop Down Menu System Field Local Mode Digital Output Field Local Mode OnlyCtcss Freq Field Local Mode Only Ctcss Default Check Box Local Mode Only LAM Time Field LAM Level Field Options Parallel Console Check Box PTT Timeout FieldWire Check Box Serial Port Mode Drop Down Menu Serial Port Params Drop Down Menu Serial Port Drop Down Menu Local Mode FleetSync Decode Check Box Tone and Local Modes Signaling Setup Tone Type Drop Down Menu FleetSync Encode Check Box Local Mode OnlyMDC Decode Check Box Tone and Local Modes MDC Encode Check Box Pause Duration Field ANI Suffix FieldDigit Duration Field Interdigit Duration Field ANI Call Format Field ANI Call Type Drop Down Menu Per Line Setup Window-Phone Mode Configuration Auto Answer FieldAuto Disconnect Time Field Click Dial String Field Mic Click Call Enabled Check BoxNumber of Clicks Field Time Between Clicks Field Relay Closure R1 Ring Check Box Click Dial Timeout Field Detect Tones Enabled Check Box Rx AGC Enabled Check BoxKeep Alive Digits Enabled Check Box Star/Pound Keying Enabled Check Box Serial Port Parameters Drop Down Menu Serial Port Mode Drop Down Menu Serial Port Params Drop Down Menu Phone Mode MDC Decode Check Box FleetSync Decode Check Box ANI Decoder Field ANI Call Type Drop Down Menu Per Line Setup Window-iDEN Radio Configuration Per Line Setup iDEN Radio Mode view Jump To Entry Drop Down Menu IDEN Number Field Call Type Drop Down Menu Per Line Setup iDEN Mode view F1 Last Call Check Box iDEN Mode only PTT Timeout Field Per Line Setup Tetra Mode view Per line Setup Window-Tetra Radio Configuration Relay Drop Down Menu ISSI/GSSI Number Field Type Drop Down Menu TX Delay Field LAM Level Field PTT Timeout Field Save Parameters Button Reset IP-223 ButtonClick Reset IP-223 Save to Eeprom Window Account Setup Window Admin System AccountUser System Account Username Display Column Enable Check BoxPassword Field New Password Field Save Button Confirm Password FieldTo enable the user account, do the following Edit Button Add New User Button Reset System Parameters ButtonEdit System Accounts Window Delete Button Password can be 4-16 alpha-numeric characters in length Add New User Window Choose a UsernameUsername Field CRP Setup & PIN Table Check Box Additional Feature Check BoxAccount Setup Check Box Basic Ethernet & Multicast Setup Check Box Tone Freq & Durations Check Box Cancel Button Edit Created Accounts Window Edit Created Account-Account Setup Additional Feature Setup Window To activate a special feature, do the following100 101 Clone Console Window 102 Crosspatch Setup Window 103 104 RCP TablesJump To Entry Drop Down Menu and Go Button Phone Field Dial option only Mode Drop Down Menu105 Delete String Field 106 Command Buttons Submit 107Next 10 Button To define the crosspatch parameters, do the following 108 CRP PIN Table Window PIN Field PIN Enable Check Box109 Entry Field To define crosspatch PIN numbers, do the following 110Prev 30 Entries Button Next 30 Entries Button 111 Pass Change Window Tone Frequency & Durations Window 112Monitor Frequency Field 113 FTone 1-16 Frequency Fields 114Function Tone Duration Field Function Tone Magnitude Field 115 116 Update Firmware Install TSM117 118 Confirm Installation Download Telex Firmware 119 Update Firmware Tool Window Firmware File Info Group Box120 Login Group Box 121Upload VoIP Hardware Firmware 122 Firmware Update Tool- Success Messages Click Close Signal Line Test point ConnectorsAdjustments Connector Description PCB 750743 or PCB 750630 revision C, D, E, and F Jumper Settings124 PCB 750743 or PCB 750630 revision F 125 Jumper Locations 126 127 Additional Resources 128 Relm RM Series Radios to 223 Series Adaptor Panels 129 Relm GMH Radios to IP-223 Adaptor Panels 130 Ctcss Tone Frequency Table 131Tone Freq Number 132 Digital Output Table 133Digital Output Values 134 European Tone Frequencies in Hz Motorola Tone Frequency Table135 Tone Number Code Digit 136 137