Internal ΦM flatness test | VXI 3002 manual

Table 5-29 Internal ΦM flatness test

Modulation	Response	Result (dB)	Response
frequency (kHz)	level min.		level max.
	(dB)		(dB)


0.1	−3	_______	+3
0.3	−3	_______	+3
1	−	reference	−
3	−3	_______	+3
10	−3	_______	+3

Table 5-30 Internal AM depth and distortion tests at −4 dBm

	AM depth 30%			AM depth 80%			Distortion

Carrier	min.	Result	max.	min.	Result	max.	Result at	Result at
frequency	(%)	(%)	(%)	(%)	(%)	(%)	30% depth	80% depth
(MHz)							(<1.5%)	(<2.5%)


1.5	28.5	_____	31.5	76	_____	84	_______	_______
6	28.5	_____	31.5	76	_____	84	_______	_______
9	28.5	_____	31.5	76	_____	84	_______	_______
11	28.5	_____	31.5	76	_____	84	_______	_______
20	28.5	_____	31.5	76	_____	84	_______	_______
50	28.5	_____	31.5	76	_____	84	_______	_______
100	28.5	_____	31.5	76	_____	84	_______	_______
200	28.5	_____	31.5	76	_____	84	_______	_______
500	28.5	_____	31.5	76	_____	84	_______	_______

Table 5-31 Internal AM depth and distortion tests at +7 dBm

	AM depth 30%			AM depth 80%			Distortion

Carrier	min.	Result	max.	min.	Result	max.	Result at	Result at
frequency	(%)	(%)	(%)	(%)	(%)	(%)	30% depth	80% depth
(MHz)							(<1.5%)	(<2.5%)


1.5	28.5	_____	31.5	76	_____	84	_______	_______
6	28.5	_____	31.5	76	_____	84	_______	_______
9	28.5	_____	31.5	76	_____	84	_______	_______
11	28.5	_____	31.5	76	_____	84	_______	_______
20	28.5	_____	31.5	76	_____	84	_______	_______
50	28.5	_____	31.5	76	_____	84	_______	_______
100	28.5	_____	31.5	76	_____	84	_______	_______
200	28.5	_____	31.5	76	_____	84	_______	_______
500	28.5	_____	31.5	76	_____	84	_______	_______

5-45

Image 120

VXI 3002 manual Internal ΦM flatness test, Internal AM depth and distortion tests at −4 dBm

Contents

3002 3002 Intended audience StructureDocument conventions Chapter Contents Preface Patent protection Symbols Symbol DescriptionGeneral conditions of use Electrical hazards DC supply voltage Fire hazard Toxic hazardsBeryllia Beryllium copper Installation Suitability for use Symboles signalant un risque Symbole Nature du risqueConditions générales d’utilisation Sécurité électrique tension d’alimentation continue Risque lié au feu Le BérylliaBronze au béryllium UtilisationPage Gefahrensymbole Symbol GefahrenartAllgemeine Hinweise zur Verwendung Elektrische Schläge Gleichspannungsversorgung Brandgefahr Warnung vor giftigen SubstanzenBeryllium Oxid Beryllium Kupfer Simboli di pericolo Condizioni generali d’usoPericoli da elettricità alimentazione a c.c Simbolo Tipo di pericolo Pericolo dincendio Pericolo sostanze tossicheBerillio Rame berillio Caratteristiche d’uso Símbolos de peligro Condiciones generales de usoNivel peligroso de electricidad tensión de alimentación DC Símbolo Naturaleza del peligro Peligro de incendio Aviso de toxicidadBerilio Berilio-cobre Idoneidad de uso Contents Main featuresChapter Introduction Incrementing Frequency sweepMemory Triggers Performance data Phase Modulation Frequency ModulationFSK Pulse Modulation Sweep Mode Internal LF GeneratorExternal Modulation Input Frequency Standard Versions, options and accessories SafetyElectromagnetic Compatibility Safety Certificate Ref. No. DC230Reference No Title Qualifying Notes Setting logical address List of figuresInitial visual inspection Ventilation requirements Installing in VXI mainframe Routine safety testing and inspectionVisual inspection Rectification Cleaning Front panel connectors and indicatorsPutting into storage Switching on Disk installation/loading instructions Introduction Device listening elementsDevice talking elements Programming Program messagesCompound headers Common commands and queries Ieee Program dataMessage exchange protocol Mnemonic Device dependent commands OPC Default settings Instrument default settings Carrier frequency CfrqCFRQ? RF level Rflv RFLV? RFLVLIMIT?RFLVOFFS? Output control OutputOUTPUT? Modulation mode Valid Mode Combinations TableMode MODE? Modulation control MODMOD? Frequency modulation and FSK FM or FM1 or FM2 Dcfmnl FMMODF? or FM1MODF? or FM2MODF? Phase modulation PM or PM1 or PM2 PMMODF? or PM1MODF? Amplitude modulation AM or AM1 or AM2 AM? or AM1? or AM2? Pulse modulation PulsePULSE? Memory stores Memory storeCarrier store Full store Recalling default settings Memory-recall Memory erase Memory sequencing Memory triggering Memory protectionMtrig MTRIG? Sweep operation SweepSWEEPCFRQ? Sweep mode SWEEP? Halt Cont Reset Retn Xfer Sweep control Trigger source SourcesTrigger TRIGGERSOURCE? RF level Atten. lock Setting dBm Min. dBm Max. dBm From Attenuator holdAttenuator lock ranges Atten Power-up options Reverse power protection Reading error messages Operating hoursFrequency standard selection Status byte Status data structure register model Standard event registers ESE ESE? Hardware event registers HSE? Coupling event registers CSE? Instrument event registers SSE SSE? Error Queue Queue flag details Status byte when read by *STB? SRE SRE? Status byte when read by serial poll Service Request Generation Service Request Enable Register# Summary of status reporting commands and queries Error handling Background errorsForeground errors Error queue Error Messages Background errors 500 599 in priority order Foreground errors 0 Ieee 488.2 errors 400 Modulation Frequency generationControl Block schematic diagram Acceptance Testing Test precautions Recommended test equipment Executable soft front panel software Specification Description Minimum specification ExampleRF output Test equipment Test procedure RF level frequency responseALC linearity Attenuator accuracy Measuring Carrier frequency accuracy Counter Spectral purity HarmonicsSpectrum analyzer Non-harmonics Residual FM SSB phase noise SSB phase noise test set-up Internal FM FM deviation and distortion FM scale shape Carrier error External FM frequency response ALC off, DC coupledHz to 100 kHz External FM frequency response ALC on Hz DC Phase modulation Phase modulation flatness AM depth and distortion Figure recorded in 5 20 log10 Figure recorded Test procedure Hz to 30 kHz AM scale shapeExternal AM frequency response ALC off, DC coupled DVM Pulse modulation RF level frequency response 10 Pulse modulation test set-up Pulse modulation on/off ratio Function generator Modulation oscillator Pulse modulation rise and fall time Modulation oscillator frequencies Modulation oscillator distortion and LF output flatness External frequency standard input 15 External standard test set-up For 3002 Signal Generator, serial number RF output at −4 dBm RF output at +7 dBm RF output at +25 dBm +19 dBm ALC linearity at 2.5 MHz RF level dBm RF level min DBm Result dBm RF level max ALC linearity at 950 MHz ALC linearity at 1200 MHz ALC linearity at 1900 MHz ALC linearity at 2400 MHz Attenuator test at 2.6 MHz RF level dBm RF level min Result dBm RF level max DBm 10 Attenuator test at 480.1 MHz 11 Attenuator test at 1199 MHz 12 Attenuator test at 1875.1 MHz 13 Attenuator test at 2399 MHz 14 Carrier frequency tests Frequency MHz Frequency min Result MHz Frequency max 15 Carrier harmonic tests at −4 dBm 16 Carrier harmonic tests at +7 dBm 17 Carrier harmonic tests at +13 dBm 18 Carrier harmonic tests at +19 dBm 21 SSB phase noise test 19 Carrier non-harmonic tests20 Residual FM test Carrier frequency Residual FM Measured value Hz RMS 23 FM scale shape tests at 15 MHz carrier FM deviation kHz Result kHz Min. kHz Max. kHz 24 Carrier error test at 1.2 GHz, FM deviation 100 kHz Carrier error Result kHz 10.5 29 Internal ΦM flatness test 30 Internal AM depth and distortion tests at −4 dBm31 Internal AM depth and distortion tests at +7 dBm 32 Internal AM depth and distortion tests at +13 dBm 33 Internal AM depth and distortion tests at +19 dBm 34 AM scale shape test AM depth % AM depth min Result % Max. % 38 Pulse modulation RF output at −7 dBm 39 Pulse modulation RF output at +4 dBm 40 Pulse modulation RF output at +14 dBm Pulse modulation on/off ratio test Modulation oscillator frequency tests 44 Modulation oscillator distortion and LF output tests45 External frequency standard tests Acceptance testing Annex aGeneral description Operation Test procedure Spectrum analyzer Annex-A-3 Table A-1 Pulse mod. RF output at −7 dBm Table A-2 Pulse mod. RF output at +0 dBm Table A-3 Pulse mod. RF output at +16 dBm Table A-4 Pulse modulation on/off ratio test Table A-5 Pulse modulation rise and fall time testResult ns Software Licence and Warranty Indemnity Email info-test@aeroflex.com China ShanghaiUK Stevenage China Beijing