RF level frequency response, ALC linearity | VXI 3002 guide

RF level frequency response

Test procedure

	UUT		6960B
	UUT		RF power meter
		6932	SENSOR
	RF OUT	6932	INPUT
	RF OUT		INPUT
		Power
		sensor
			C2558

Fig. 5-1 RF output test set-up

(1)Perform AUTO ZERO and AUTO CAL on the power meter.

(2)Connect the test equipment as shown in Fig. 5-1.

(3)On the UUT set:

Carr Freq	30 kHz
RF Level	0 dBm

(4)Record the output level measured by the power meter against each of the carrier frequencies shown in Table 5-1 checking that the results are within specification.

(5)Set the UUT RF level to +7 dBm and repeat (4) using Table 5-2.

(6)Set the UUT RF level to +25 dBm and repeat (4) using Table 5-3, decreasing the RF level to +19 dBm when testing at carrier frequencies above 1.2 GHz.

ALC linearity

Test procedure

(1)Perform AUTO ZERO and AUTO CAL on the power meter.

(2)Connect the test equipment as shown in Fig. 5-1.

(3)On the UUT set:

Carr Freq	2.5 MHz
RF Level	−4 dBm

(4)Record the output level measured by the power meter against each of the steps shown in Table 5-4 checking that the results are within specification.

(5)Set the UUT carrier frequency to 950 MHz and repeat (4) using Table 5-5.

(6)Set the UUT carrier frequency to 1200 MHz and repeat (4) using Table 5-6.

(7)Set the UUT carrier frequency to 1900 MHz and repeat (4) using Table 5-7.

(8)Set the UUT carrier frequency to 2400 MHz and repeat (4) using Table 5-8.

5-4

Image 79

VXI 3002 manual RF level frequency response, ALC linearity, Test procedure

Contents

3002 3002 Chapter Intended audienceStructure Document conventions Contents Patent protection Preface Electrical hazards DC supply voltage SymbolsSymbol Description General conditions of use Beryllium copper Fire hazardToxic hazards Beryllia Suitability for use Installation Sécurité électrique tension d’alimentation continue Symboles signalant un risqueSymbole Nature du risque Conditions générales d’utilisation Utilisation Risque lié au feuLe Béryllia Bronze au bérylliumPage Elektrische Schläge Gleichspannungsversorgung GefahrensymboleSymbol Gefahrenart Allgemeine Hinweise zur Verwendung Beryllium Kupfer BrandgefahrWarnung vor giftigen Substanzen Beryllium Oxid Simbolo Tipo di pericolo Simboli di pericoloCondizioni generali d’uso Pericoli da elettricità alimentazione a c.c Rame berillio Pericolo dincendioPericolo sostanze tossiche Berillio Caratteristiche d’uso Símbolo Naturaleza del peligro Símbolos de peligroCondiciones generales de uso Nivel peligroso de electricidad tensión de alimentación DC Berilio-cobre Peligro de incendioAviso de toxicidad Berilio Idoneidad de uso Introduction ContentsMain features Chapter Triggers IncrementingFrequency sweep Memory Performance data Pulse Modulation Phase ModulationFrequency Modulation FSK Frequency Standard Sweep ModeInternal LF Generator External Modulation Input Compatibility Versions, options and accessoriesSafety Electromagnetic Qualifying Notes SafetyCertificate Ref. No. DC230 Reference No Title Ventilation requirements Setting logical addressList of figures Initial visual inspection Rectification Installing in VXI mainframeRoutine safety testing and inspection Visual inspection Front panel connectors and indicators CleaningPutting into storage Disk installation/loading instructions Switching on Device listening elements IntroductionDevice talking elements Program messages ProgrammingCompound headers Mnemonic Common commands and queries IeeeProgram data Message exchange protocol OPC Device dependent commands Instrument default settings Default settings Cfrq Carrier frequencyCFRQ? Rflv RF level RFLVLIMIT? RFLV?RFLVOFFS? Output Output controlOUTPUT? MODE? Modulation modeValid Mode Combinations Table Mode MOD Modulation controlMOD? FM or FM1 or FM2 Frequency modulation and FSK FMMODF? or FM1MODF? or FM2MODF? Dcfmnl PM or PM1 or PM2 Phase modulation PMMODF? or PM1MODF? AM or AM1 or AM2 Amplitude modulation AM? or AM1? or AM2? Pulse Pulse modulationPULSE? Full store Memory storesMemory store Carrier store Memory-recall Recalling default settings Memory sequencing Memory erase MTRIG? Memory triggeringMemory protection Mtrig Sweep Sweep operationSWEEPCFRQ? SWEEP? Sweep mode Sweep control Halt Cont Reset Retn Xfer TRIGGERSOURCE? Trigger sourceSources Trigger Atten RF level Atten. lock Setting dBm Min. dBm Max. dBm FromAttenuator hold Attenuator lock ranges Reverse power protection Power-up options Operating hours Reading error messagesFrequency standard selection Status byte Status data structure register model ESE ESE? Standard event registers HSE? Hardware event registers CSE? Coupling event registers SSE SSE? Instrument event registers Queue flag details Error Queue SRE SRE? Status byte when read by *STB? Service Request Generation Service Request Enable Register# Status byte when read by serial poll Summary of status reporting commands and queries Error queue Error handlingBackground errors Foreground errors Background errors 500 599 in priority order Error Messages Foreground errors 0 Ieee 488.2 errors 400 Frequency generation ModulationControl Block schematic diagram Test precautions Acceptance Testing Executable soft front panel software Recommended test equipment Test equipment SpecificationDescription Minimum specification Example RF output RF level frequency response Test procedureALC linearity Measuring Attenuator accuracy Counter Carrier frequency accuracy Harmonics Spectral puritySpectrum analyzer Residual FM Non-harmonics SSB phase noise test set-up SSB phase noise FM deviation and distortion Internal FM FM scale shape External FM frequency response ALC off, DC coupled Carrier errorHz to 100 kHz Hz DC External FM frequency response ALC on Phase modulation flatness Phase modulation Figure recorded in 5 20 log10 Figure recorded AM depth and distortion AM scale shape Test procedure Hz to 30 kHzExternal AM frequency response ALC off, DC coupled DVM 10 Pulse modulation test set-up Pulse modulation RF level frequency response Function generator Pulse modulation on/off ratio Pulse modulation rise and fall time Modulation oscillator Modulation oscillator distortion and LF output flatness Modulation oscillator frequencies 15 External standard test set-up External frequency standard input RF output at −4 dBm For 3002 Signal Generator, serial number RF output at +7 dBm +19 dBm RF output at +25 dBm RF level dBm RF level min DBm Result dBm RF level max ALC linearity at 2.5 MHz ALC linearity at 950 MHz ALC linearity at 1200 MHz ALC linearity at 1900 MHz ALC linearity at 2400 MHz RF level dBm RF level min Result dBm RF level max DBm Attenuator test at 2.6 MHz 10 Attenuator test at 480.1 MHz 11 Attenuator test at 1199 MHz 12 Attenuator test at 1875.1 MHz 13 Attenuator test at 2399 MHz Frequency MHz Frequency min Result MHz Frequency max 14 Carrier frequency tests 15 Carrier harmonic tests at −4 dBm 16 Carrier harmonic tests at +7 dBm 17 Carrier harmonic tests at +13 dBm 18 Carrier harmonic tests at +19 dBm Carrier frequency Residual FM Measured value Hz RMS 21 SSB phase noise test19 Carrier non-harmonic tests 20 Residual FM test FM deviation kHz Result kHz Min. kHz Max. kHz 23 FM scale shape tests at 15 MHz carrier Carrier error Result kHz 24 Carrier error test at 1.2 GHz, FM deviation 100 kHz 10.5 30 Internal AM depth and distortion tests at −4 dBm 29 Internal ΦM flatness test31 Internal AM depth and distortion tests at +7 dBm 33 Internal AM depth and distortion tests at +19 dBm 32 Internal AM depth and distortion tests at +13 dBm AM depth % AM depth min Result % Max. % 34 AM scale shape test 38 Pulse modulation RF output at −7 dBm 39 Pulse modulation RF output at +4 dBm Pulse modulation on/off ratio test 40 Pulse modulation RF output at +14 dBm 44 Modulation oscillator distortion and LF output tests Modulation oscillator frequency tests45 External frequency standard tests Operation Acceptance testingAnnex a General description Spectrum analyzer Test procedure Annex-A-3 Table A-1 Pulse mod. RF output at −7 dBm Table A-2 Pulse mod. RF output at +0 dBm Table A-3 Pulse mod. RF output at +16 dBm Table A-5 Pulse modulation rise and fall time test Table A-4 Pulse modulation on/off ratio testResult ns Software Licence and Warranty Indemnity China Beijing Email info-test@aeroflex.comChina Shanghai UK Stevenage