Coupling event registers, Cse? | VXI 3002 guide

STATUS BYTE

Coupling event registers

This is a device dependent register and the bits have meanings as shown in the list at the bottom of the page.

Condition

Register

CCR?			d15		d14
	Transition
	Filter	#
	Filter	#
Register
Register			d15		d14
Read/Write			d15		d14
Commands
Commands
	Status
	Register

CSR?			d15		d14

	d3		d2		d1		d0

d3

d2

d1

d0


	d3		d2		d1		d0

&

OR

Enable

Register

&

&

&

&

&

CSE	e	15	e14
CSE?

	e3	e2	e1	e0

<csb>

# Positive transition sets status.

C1625

d0 d1 d2 d3 d4 d5 d6

d7 - d15

<csb>

RF level restricted by requested AM depth not used

not used

AM2 depth restricted by requested AM1 depth

FM2 deviation restricted by requested FM1 deviation ΦM2 deviation restricted by requested ΦM1 deviation not used

not used

coupling event register summary bit

3-34

Image 64

VXI 3002 manual Coupling event registers, Cse?

Contents

3002 3002 Intended audience StructureDocument conventions Chapter Contents Preface Patent protection Symbols Symbol DescriptionGeneral conditions of use Electrical hazards DC supply voltage Fire hazard Toxic hazardsBeryllia Beryllium copper Installation Suitability for use Symboles signalant un risque Symbole Nature du risqueConditions générales d’utilisation Sécurité électrique tension d’alimentation continue Risque lié au feu Le BérylliaBronze au béryllium UtilisationPage Gefahrensymbole Symbol GefahrenartAllgemeine Hinweise zur Verwendung Elektrische Schläge Gleichspannungsversorgung Brandgefahr Warnung vor giftigen SubstanzenBeryllium Oxid Beryllium Kupfer Simboli di pericolo Condizioni generali d’usoPericoli da elettricità alimentazione a c.c Simbolo Tipo di pericolo Pericolo dincendio Pericolo sostanze tossicheBerillio Rame berillio Caratteristiche d’uso Símbolos de peligro Condiciones generales de usoNivel peligroso de electricidad tensión de alimentación DC Símbolo Naturaleza del peligro Peligro de incendio Aviso de toxicidadBerilio Berilio-cobre Idoneidad de uso Contents Main featuresChapter Introduction Incrementing Frequency sweepMemory Triggers Performance data Phase Modulation Frequency ModulationFSK Pulse Modulation Sweep Mode Internal LF GeneratorExternal Modulation Input Frequency Standard Versions, options and accessories SafetyElectromagnetic Compatibility Safety Certificate Ref. No. DC230Reference No Title Qualifying Notes Setting logical address List of figuresInitial visual inspection Ventilation requirements Installing in VXI mainframe Routine safety testing and inspectionVisual inspection Rectification Front panel connectors and indicators CleaningPutting into storage Switching on Disk installation/loading instructions Device listening elements IntroductionDevice talking elements Program messages ProgrammingCompound headers Common commands and queries Ieee Program dataMessage exchange protocol Mnemonic Device dependent commands OPC Default settings Instrument default settings Cfrq Carrier frequencyCFRQ? RF level Rflv RFLVLIMIT? RFLV?RFLVOFFS? Output Output controlOUTPUT? Modulation mode Valid Mode Combinations TableMode MODE? MOD Modulation controlMOD? Frequency modulation and FSK FM or FM1 or FM2 Dcfmnl FMMODF? or FM1MODF? or FM2MODF? Phase modulation PM or PM1 or PM2 PMMODF? or PM1MODF? Amplitude modulation AM or AM1 or AM2 AM? or AM1? or AM2? Pulse Pulse modulationPULSE? Memory stores Memory storeCarrier store Full store Recalling default settings Memory-recall Memory erase Memory sequencing Memory triggering Memory protectionMtrig MTRIG? Sweep Sweep operationSWEEPCFRQ? Sweep mode SWEEP? Halt Cont Reset Retn Xfer Sweep control Trigger source SourcesTrigger TRIGGERSOURCE? RF level Atten. lock Setting dBm Min. dBm Max. dBm From Attenuator holdAttenuator lock ranges Atten Power-up options Reverse power protection Operating hours Reading error messagesFrequency standard selection Status byte Status data structure register model Standard event registers ESE ESE? Hardware event registers HSE? Coupling event registers CSE? Instrument event registers SSE SSE? Error Queue Queue flag details Status byte when read by *STB? SRE SRE? Status byte when read by serial poll Service Request Generation Service Request Enable Register# Summary of status reporting commands and queries Error handling Background errorsForeground errors Error queue Error Messages Background errors 500 599 in priority order Foreground errors 0 Ieee 488.2 errors 400 Frequency generation ModulationControl Block schematic diagram Acceptance Testing Test precautions Recommended test equipment Executable soft front panel software Specification Description Minimum specification ExampleRF output Test equipment RF level frequency response Test procedureALC linearity Attenuator accuracy Measuring Carrier frequency accuracy Counter Harmonics Spectral puritySpectrum analyzer Non-harmonics Residual FM SSB phase noise SSB phase noise test set-up Internal FM FM deviation and distortion FM scale shape External FM frequency response ALC off, DC coupled Carrier errorHz to 100 kHz External FM frequency response ALC on Hz DC Phase modulation Phase modulation flatness AM depth and distortion Figure recorded in 5 20 log10 Figure recorded AM scale shape Test procedure Hz to 30 kHzExternal AM frequency response ALC off, DC coupled DVM Pulse modulation RF level frequency response 10 Pulse modulation test set-up Pulse modulation on/off ratio Function generator Modulation oscillator Pulse modulation rise and fall time Modulation oscillator frequencies Modulation oscillator distortion and LF output flatness External frequency standard input 15 External standard test set-up For 3002 Signal Generator, serial number RF output at −4 dBm RF output at +7 dBm RF output at +25 dBm +19 dBm ALC linearity at 2.5 MHz RF level dBm RF level min DBm Result dBm RF level max ALC linearity at 950 MHz ALC linearity at 1200 MHz ALC linearity at 1900 MHz ALC linearity at 2400 MHz Attenuator test at 2.6 MHz RF level dBm RF level min Result dBm RF level max DBm 10 Attenuator test at 480.1 MHz 11 Attenuator test at 1199 MHz 12 Attenuator test at 1875.1 MHz 13 Attenuator test at 2399 MHz 14 Carrier frequency tests Frequency MHz Frequency min Result MHz Frequency max 15 Carrier harmonic tests at −4 dBm 16 Carrier harmonic tests at +7 dBm 17 Carrier harmonic tests at +13 dBm 18 Carrier harmonic tests at +19 dBm 21 SSB phase noise test 19 Carrier non-harmonic tests20 Residual FM test Carrier frequency Residual FM Measured value Hz RMS 23 FM scale shape tests at 15 MHz carrier FM deviation kHz Result kHz Min. kHz Max. kHz 24 Carrier error test at 1.2 GHz, FM deviation 100 kHz Carrier error Result kHz 10.5 30 Internal AM depth and distortion tests at −4 dBm 29 Internal ΦM flatness test31 Internal AM depth and distortion tests at +7 dBm 32 Internal AM depth and distortion tests at +13 dBm 33 Internal AM depth and distortion tests at +19 dBm 34 AM scale shape test AM depth % AM depth min Result % Max. % 38 Pulse modulation RF output at −7 dBm 39 Pulse modulation RF output at +4 dBm 40 Pulse modulation RF output at +14 dBm Pulse modulation on/off ratio test 44 Modulation oscillator distortion and LF output tests Modulation oscillator frequency tests45 External frequency standard tests Acceptance testing Annex aGeneral description Operation Test procedure Spectrum analyzer Annex-A-3 Table A-1 Pulse mod. RF output at −7 dBm Table A-2 Pulse mod. RF output at +0 dBm Table A-3 Pulse mod. RF output at +16 dBm Table A-5 Pulse modulation rise and fall time test Table A-4 Pulse modulation on/off ratio testResult ns Software Licence and Warranty Indemnity Email info-test@aeroflex.com China ShanghaiUK Stevenage China Beijing