Whirlpool MFW 9600S, MFW 9700S manual 1233456768479346724, 2273

12Once the bolt is loose, move it to the center of the hole and

completely pull out the bolt, including the plastic spacer

32covering the bolt.

Once all 4 bolts are removed discard bolt and spacers. Then pull the power cord through the opening of the rear panel and

42close the hole with the attached cap.

56789Close the bolt holes with the 4 transport bolt hole plugs.

If the washer is to be transported at a later date, call your local service center. To avoid suspension and structural damage to your washer, it must be properly set up for relocation by a certified technician.

12334567684793￿467￿2￿4￿

￿2Make sure the washer drum is empty.

Attach the hose with the red color indicator to the Hot (left) inlet valve. Attaching the red coupling first makes it easier to tighten connection with pliers. Screw on coupling by hand

12until it is seated on the washer.

Attach the hose with the blue color indicator to the Cold (right) water inlet valve. Screw on coupling by hand until it is seated on the washer.

12￿21345674895￿3￿￿5674895￿￿￿￿￿￿8484

32Using pliers, check the tightness of the hose couplings already56789attached to the washer.

Do not overtighten. Damage to the coupling can

42result.

Attach the hose with the red color indicator to the hot water faucet. Screw on coupling by hand until it is seated on the

￿2washer.

Attach the hose with the blue color indicator to the cold water faucet. Screw on coupling by hand until it is seated on the washer.

￿2Using pliers, tighten the couplings with an additional two-thirds turn.

￿2 Do not overtighten. Damage to the coupling can result.

56Turn789on the water faucets and check for leaks.

Replace inlet hoses after 5 years of use to reduce the risk of hose failure. Record hose installation or replacement dates on the hoses for future reference.

Periodically inspect and replace hoses if bulges, kinks, cuts, wear, or leaks are found.

￿2￿6476847￿ 37￿2￿4

Proper routing of the drain hose protects your floors from damage due￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿to water leakage. Read and follow these instructions.

Gently pull the corrugated drain hose from the shipping clips.

￿!￿￿￿"￿￿!￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿#￿#￿￿￿￿￿￿￿

Connect the drain hose form to the corrugated drain hose.

7￿￿$￿￿#8￿￿3￿￿4564￿8958￿￿￿￿￿￿%￿￿%￿￿￿￿￿224￿85785￿97￿￿5385354￿￿8554895￿￿8539￿￿97￿97￿￿745￿￿33￿5￿$8￿85￿39￿54354￿85￿97￿￿￿￿￿5￿3￿85￿39￿57￿￿5￿￿7￿5￿￿435￿￿7￿82￿￿2 ￿5￿3￿85745

Do not straighten the drain hose, and do not force excess drain hose into standpipe. Hose should be secure, but loose enough to provide a gap for air.

Do not lay excess hose on the bottom of the laundry tub.

￿￿22￿7￿￿￿￿3

You may need additional parts. See Floor drain under Tools and Parts.

2-5