D i s p l a y e d C o n t r o l P a n e l M e s s a g e s

Figure 7.2

Control Panel messages (continued)

 

 

 

Message

 

Description/Action

 

 

 

0101

 

SIMM in slot 1 has failed.

Appears in the top left ACTION: Move the SIMM to Slot 0; see “Installing a SIMM” (page 5-4). If a

side of the display.

memory error (0100) occurs again, replace the SIMM. If there is no error, the main

Indicates which module

controller board has failed. Contact your dealer or Xerox / Rank Xerox.

failed.

 

 

1000

Communication has failed between the printer controller and the printer.

Appears in the top left ACTION: Verify the controller board is seated properly. If the message still appears,

side of the display.

replace the controller, replace the interface between the controller and printer

Indicates which module

engine, or replace the print engine; or, contact your dealer or Xerox / Rank Xerox.

failed.

 

 

2000

A key on the Control Panel is stuck in the down position.

Appears in the top left ACTION: Press any key. If no response, the Control Panel may need to be replaced.

side of the display.

Contact your dealer or Xerox / Rank Xerox.

 

Indicates which module

 

 

 

 

 

 

 

 

 

 

failed.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Both Cards Out

Upper and lower font cards were removed while the printer was offline, but the

Replace Original

cards were still being used by the software application.

 

ACTION: To clear the error message and resume printing, reseat or reinstall the

 

cards. Press Online

 

 

 

On completion of the print job, you can take the printer

 

 

 

 

 

offline and remove the cards.

 

 

 

 

 

 

 

 

 

Card Err. both

Both the upper and lower font cards were removed while the printer was online.

Power Off & On

ACTION: Power OFF the printer, then power it ON to resume.

 

 

 

 

 

 

 

 

 

 

 

Close Cover

The main cover is open.

 

 

 

 

 

 

ACTION: Close it, then press Online

 

 

 

to resume normal operation.

 

 

 

 

 

 

 

 

 

 

 

 

Comm. Error

If your printer is configured for serial, a framing or parity error has occurred on the

 

serial interface.

 

 

 

 

 

 

ACTION: You have a mismatch between your printer and the host. Check your

 

printer serial configuration (baud rate, handshake, parity, etc.) to be certain the

 

serial settings match your host (page 3-45). If problem persists, contact your dealer

 

or Xerox / Rank Xerox.

 

 

 

 

 

 

If your printer is configured for parallel, the printer is not able to communicate

 

with the host using bidirectional parallel.

 

 

ACTION: Check the parallel cable to make sure it is connected properly on both

 

the printer and the host. Inspect the parallel cable for any defects; if wires are

 

broken or the cable appears to be damaged, replace the cable. Check the host to

 

be certain that it is configured properly. Under the Parallel Menu, turn

 

Bidirectional Off. If problem persists, contact your dealer or Xerox / Rank Xerox.

7-64 5 0 5 / 4 5 0 5 p s o r 4 5 1 0 / 4 5 1 0 p s U s e r ’ s G u i d e

Page 172
Image 172
Xerox 4505/4505ps manual 0101†, 1000†, 2000†, Both Cards Out, Replace Original, Card Err. both, Power Off & On, Close Cover