280 Anhang C: MIDI

If [TABLE] is selected

STATUS

1011nnnn

Bn

Control change

DATA

0ccccccc

cc

Control number (0-95, 102-119)

 

0vvvvvvv

vv

Control value (0-127)

If [NRPN] is selected

8. CONTINUE (FB)

Reception

This message is received if the automix TIME REFERENCE setting is MIDI CLOCK, and will cause automix to start from the current song position. In actuality, automix will start when the next TIMING CLOCK is received after receiving the CONTINUE message.

STATUS

1011nnnn

Bn

DATA

01100010

62

 

0vvvvvvv

vv

STATUS

1011nnnn

Bn

DATA

01100011

63

 

0vvvvvvv

vv

STATUS

1011nnnn

Bn

DATA

00100110

26

 

0vvvvvvv

vv

STATUS

1011nnnn

Bn

DATA

00000110

06

 

0vvvvvvv

vv

Control change

 

NRPN LSB

 

LSB of parameter number

 

Control change

*1

NRPN MSB

 

MSB of parameter number

 

Control change

*1

LSB of data entry

 

LSB of parameter data

 

Control change

*1, *2

MSB of data entry

*2

MSB of parameter data

*2

STATUS

11111011 FB Continue

9. STOP (FC)

Reception

This message is received if the automix TIME REFERENCE setting is MIDI CLOCK, and will cause automix to stop.

STATUS

11111100 FC Stop

10. ACTIVE SENSING (FE)

Reception

Once this message has been received, the failure to receive any message for an interval of 400 ms or longer will cause MIDI transmission to be initial- ized, such as by clearing the Running Status.

*1) There is no particular need to add the 2nd, 3rd, and 4th status for transmission. However if these are present during recep- tion, they should be received.

*2) Does not need to be transmitted if the parameter data fits within 7 bits.

4. PROGRAM CHANGE (Cn)

Reception

This message is received if [Program Change RX] is ON and [Rx CH] matches. However if [OMNI] is ON, this is received regardless of the chan- nel.

A scene memory will be recalled according to the settings of the [Program Change Table].

This message will be echoed if [Program Change ECHO] is ON.

Transmission

If [Program Change TX] is ON, this message is transmitted according to the settings of the [Program Change Table] on the [Tx CH] channel when a scene memory is recalled.

If the recalled scene has been assigned to more than one program number, the lowest-numbered program number will be transmitted. Transmission to Studio Manager using Program Change messages will not be performed since there is no guarantee that the contents of the tables will match. (Pa- rameter Changes will always be used.)

STATUS

1100nnnn

Cn

Program change

DATA

0nnnnnnn

nn

Program number (0-127)

5. SONG POSITION POINTER (F2)

Reception

If this is received when the automix TIME REFERENCE setting is MIDI CLOCK, the automix will move to the song position that was received.

STATUS

11110010

F2

Song position pointer

DATA

0vvvvvvv

vv

Song position LSB

 

0vvvvvvv

vv

Song position MSB

6. TIMING CLOCK (F8)

Reception

If the automix TIME REFERENCE setting is MIDI CLOCK, this message is used to synchronize automix. It is also used to control effects. This message is transmitted 24 times per quarter note.

STATUS

11111000 F8 Timing clock

7. START (FA)

Reception

This message is received if the automix TIME REFERENCE setting is MIDI CLOCK, and will start the automix. In actuality, automix will start when the next TIMING CLOCK is received after receiving the START message.

STATUS

11111010 FA Start

STATUS

11111101 FE Active sensing

11. SYSTEM RESET (FF)

Reception

When this message is received, MIDI communications will be cleared, e.g., by clearing the Running Status.

STATUS

11111111 FF System reset

12.SYSTEM EXCLUSIVE MESSAGE (F0)

12.1MIDI MACHINE CONTROL (MMC)

These messages are transmitted when the Machine Control section of the 02R96 is operated. For details, refer to the MMC specification.

12.2 BULK DUMP

This message sends or receives the contents of various memories stored within the 02R96.

The basic format is as follows.

For DUMP DATA

F0 43 0n 7E cc cc <Model ID> tt mm mm [Data ...] cs F7

For DUMP REQUEST

F0 43 2n 7E <Model ID> tt mm mm F7

nDevice Number

cc cc

DATA COUNT (the number of bytes that follow this, ending

 

before the checksum)

<Model ID> Model ID (for the 02R96, this is 4C 4D 20 20 38 43 35 34)

ttDATA TYPE

mm

mm

DATA NUMBER

cs

 

CHECK SUM

A unique header (Model ID) is used to determine whether the device is a 02R96.

CHECK SUM is obtained by adding the bytes that follow BYTE COUNT (LOW) and end before CHECK SUM, taking the binary compliment of this sum, and then setting bit 7 to 0.

CHECK SUM = (-sum)&0x7F

Reception

This message is received if [Bulk RX] is ON and the [Rx CH] matches the device number included in the SUB STATUS.

When a bulk dump is received, it is immediately written into the specified memory.

When a bulk dump request is received, a bulk dump is immediately trans- mitted.

Transmission

This message is transmitted on the [Tx CH] by key operations in the [MI- DI]-[BULK DUMP] screen.

A bulk dump is transmitted on the [Rx CH] in response to a bulk dump

02R96—Bedienungsanleitung