Yamaha III manual 74

Reference

Basic Structure of the DTXTREME III

mode Sampling mode Chain mode Utility mode File mode Trigger mode Click mode Song mode Kit Drum Reference

Paramater	Descriptions
name
GateTime	Determines the gate time of the sliced portion.
H.Freq	Determines the center frequency of the high EQ
	band that is attenuated/boosted.
H.Gain	Determines the amount of boost or attenuation
	applied to the high EQ band.
Height	Determines the height of the simulated room.
	Determines the amount of time from the moment a
HiAtk	note is played to the moment the compressor is
	applied to the high frequencies.
HiGain	Determines the output gain for the high frequencies.
HiLvl	Determines the level of the high frequencies.
HiMute	Switches the mute status of the high frequencies.
	[For MULTI BAND COMP]
HiRat	Determines the ratio of the compressor for the high
	frequencies.
HiRat	[For REVERB effects]
	Adjusts the resonance of the high frequencies.
HiTh	Determines the minimum input level at which the
	effect is applied to the high frequencies.
HornF	Determines the speed of the horn when the slow/fast
	switch is set to “fast.”
HornS	Determines the speed of the horn when the slow/fast
	switch is set to “slow.”
HPF	Determines the Cutoff frequency of the High Pass
	Filter.
InitDly	Determines the amount of time that elapses between
	the direct, original sound and the initial reflections.
InitDly1	Determines the delay time for the 1st series.
InitDly2	Determines the delay time for the 2nd series.
InitDlyL	Determines the delay time of the left channel.
InitDlyR	Determines the delay time of the right channel.
InpLvl	Determines the input level.
InpMode	Selects mono or stereo configuration for the input
	sound.
InpSelect	Selects an input.
L.Freq	Determines the center frequency of the low EQ band
	that is attenuated/boosted.
L.Gain	Determines the amount of boost or attenuation
	applied to the low EQ band.
L/RDiffuse	Determines the spread of the sound.
L/RDpth	Determines the depth of the L/R pan effect.
	Determines the lagging time additionally applied to
Lag	the delayed sound, and is specified via a note length.
	This helps in setting rhythmic effects that match the
	timing of the music.
	[For CHORUS effects, RING MODULATOR, CLAS-
	SIC FLANGER, TEMPO FLANGER]
LFODpth	Determines the depth of the modulation.
	[For TEMPO PHASER]
	Determines the depth of the phase modulation.
LFOPhDiff	Determines the L/R phase difference of the modu-
	lated wave.
LFOPhRst	Determines how the initial phase of the LFO is reset.
	[For CHORUS effects, TREMOLO, RING MODULA-
	TOR, CLASSIC FLANGER, TEMPO FLANGER]
	Determines the frequency of the modulation.
	[For TEMPO PHASER]
LFOSpeed	Determines the modulation speed via a note length.
	This helps in setting rhythmic effects that match the
	timing of the music.
	[For AUTO PAN]
	Determines the frequency of the Auto Pan.
	[For CLASSIC FLANGER, RING MODULATOR]
	Selects the wave for modulation.
LFOWave	[For AUTO WAH]
	Selects the wave, sine or square.
	[For AUTO PAN]
	Determines the panning curve.

Paramater	Descriptions
name
Livenss	Determines the decay characteristics of Early Reflec-
	tion.
	Determines the amount of time from the moment a
LowAtk	note is pressed to the moment the compressor is
	applied to the low frequencies.
LowGain	Determines the output gain for the low frequencies.
LowLvl	Determines the output level for the low frequencies.
LowMute	Determines whether the low frequency band is off or
	on.
	[For MULTI BAND COMP]
LowRat	Determines the ratio of the compressor for the low
	frequencies.
LowRat	[For REVERB effects]
	Determines the ratio of the low frequencies.
LowTh	Determines the minimum input level at which the
	effect is applied to the low frequencies.
LPF	Determines the cutoff frequency of the low pass filter.
LPFReso	Determines the Resonance of the Low Pass Filter for
	the input sound.
M.Freq	Determines the center frequency of the middle EQ
	band that is attenuated/boosted.
M.Gain	Determines the amount of boost or attenuation
	applied to the middle EQ band.
M.Width	Determines the width of the middle EQ band.
	[For FLANGER]
Manual	Determines the offset value of the delay modulation.
	[For PHASER MONO, PHASER STEREO]
	Determines the offset value of the phase modulation.
MicAngl	Determines the L/R angle of the microphone.
	Determines the amount of time from the moment a
MidAtk	note is pressed to the moment the compressor is
	applied to the mid frequencies.
MidGain	Determines the output gain for the mid frequencies.
MidLvl	Determines the output level for the mid frequencies.
MidMute	Switches the mute status of the mid frequencies.
MidRat	Determines the ratio of the compressor for the mid
	frequencies.
MidTh	Determines the minimum input level at which the
	effect is applied for the mid frequencies.
Mix	Determines the volume of the effect sound.
MixLvl	Determines the level of the effect sound mixed to the
	dry sound.
ModDpth	Determines the depth of the modulation.
ModDptR	Determines the depth of the modulation for the right
	channel as offset.
Mode	Determines the phaser type, or more specifically, the
	factor for forming the phaser effect.
ModFB	Determines the feedback level to the modulation.
ModGain	Determines the gain of the modulation.
ModLPF	Determines the cutoff frequency of the low pass filter
	applied to the modulated sound.
ModLPFReso	Determines the resonance of the low pass filter for
	the modulated sound.
ModMix	Determines the mix balance of the modulated ele-
	ment.
ModPh	Determines the L/R phase difference of the modu-
	lated wave.
ModSpd	Determines the modulation speed.
ModWave	Selects the wave type for modulation.
	Determines how long it takes to move the sound from
MoveSpeed	the current status to the sound specified via the
	Vowel parameter.
NoiseQ	Determines the resonance of the low pass filter
	applied to the noise.
NoisLPF	Determines the cutoff frequency of the low pass filter
	applied to the noise.
NoisLvl	Determines the noise level.

74 DTXTREME III Owner’s Manual