Yamaha III manual 75

Reference

Basic Structure of the DTXTREME III

Paramater	Descriptions
name
NoisModDpt	Determines the depth of the noise modulation.
NoisModSpd	Determines the speed of the noise modulation.
NoisTon	Determines the characteristics of the noise.
On/Off	Turns the isolator on or off.
OSCFrqCors	Determines the frequency for modulating the input
	wave.
OSCFrqFine	Finely determines the frequency for modulating the
	input wave.
OutGain	Determines the level gain.
OutLvl	Determines the output level.
OutLvl1	Determines the output level for the 1st series.
OutLvl2	Determines the output level for the 2nd series.
Output	Determines the output level.
OverDr	Determines the degree and character of the distor-
	tion effect.
Pan1	Determines the pan position for the 1st series.
Pan2	Determines the pan position for the 2nd series.
	This parameter of the Slice effect determines the
PanAEGLvl	minimum level of the AEG applied to the panned
	sound.
PanAEGType	This parameter of the Slice effect determines the
	type of the AEG applied to the panned sound
PanDirectn	Determines the type of the Auto Pan.
PanDpth	Determines the depth of the pan effect.
PanType	Determines the pan type.
PhShiftOfst	Determines the offset value of the phase modulation.
Pitch1	Determines the pitch in semitones for the 1st series.
Pitch2	Determines the pitch in semitones for the 2nd series.
PMDepth	Determines the depth of the pitch modulation.
Pre-LPF	Determines the Cutoff frequency of the Low Pass Fil-
	ter before the modulation.
PreLPFReso	Determines the Resonance of the Low Pass Filter for
	the input sound.
PreModHPF	Determines the Cutoff frequency of the High Pass
	Filter before the modulation.
Presenc	This guitar amp effect parameter controls the high
	frequencies.
Ratio	Determines the ratio of the compressor.
RelCurv	Determines the release curve of the envelope fol-
	lower.
	Determines the amount of time that elapses between
Release	the release or end of a sound and the end of the
	compressor effect.
RelTime	Determines the release time of the envelope follower.
Reso	Determines the resonance of the filter.
ResoOfst	Determines the resonance as offset.
RevDly	Determines the delay time from the early reflections
	until the reverberations.
RevTime	Determines the reverb time.
RoomSize	Determines the room capacity.
Rotor/Horn	Determines the volume balance of the horn and
	rotor.
RotorF	Determines the speed of the rotor when the slow/fast
	switch is set to “fast.”
RotorS	Determines the speed of the rotor when the slow/fast
	switch is set to “slow.”
	[For FLANGER&PHASER effects, TECH effects]
	Determines the sensitivity of the modulation applied
Sens	to the input change.
	[For TOUCH WAH]
	Determines the sensitivity of the wah filter’s change
	applied to the input change.
	Determines how long it takes for the rotation speed of
S-FTmHorn	the horn to change from the current speed (slow or
	fast) to another speed (fast or slow) when the rotation
	speed is switched.

Paramater	Descriptions
name
	Determines how long it takes for the rotation speed of
S-FTmRotor	the rotor to change from the current speed (slow or
	fast) to the another speed (fast or slow) when the
	rotation speed is switched.
SmplFrqCtr	Controls the sampling frequency.
SpcType	Selects the type of space simulation.
Speaker	Selects the type of speaker simulation.
	[For FLANGER]
	Determines the frequency of the LFO wave which
	controls the cyclic change of the delay modulation.
Speed	[For PHASER MONO, PHASER STEREO]
	Determines the frequency of the LFO wave which
	controls the cyclic change of the phase modulation.
	[For AUTO WAH]
	Determines the speed of the LFO.
SpeedCtrl	Switches the rotary speed.
Spread	Determines the spread of the sound.
Stage	Determines the step number of the phase shifter.
Thresh	Determines the minimum input level at which the
	effect is applied.
Top*3	Determines the maximum value of the wah filter.
	[For FLANGER]
	Determines the type of flanger.
Type	[For WAH effects]
	Determines the type of Wah.
	[For EARLY REFLECTION]
	Determines the type of the reflection sound.
Vowel	Selects a vowel type.
WallVary	Determines the wall status of the simulated room.
	Higher settings produces more diffuse reflections.
Width	Determines the width of the simulated room.
WordLen	Determines the resolution of the sound, or how
	“rough” the sound is.

*1 The Bottom parameter is available only when the value is less than that of the Top parameter.

*2 The Color parameter may not be effective depending on the values of the Mode and Stage parameters.

*3 The Top parameter is available only when the value is more than that of the Bottom parameter.

Sampling mode Chain mode Utility mode File mode Trigger mode Click mode Song mode Drum Kit mode Reference

DTXTREME III Owner’s Manual 75