■Speaker impedance SPEAKER IMP.
Use this feature to set the speaker impedance of this unit
so that it matches that of your speakers. Choices: 8ΩMIN, 6ΩMIN
• Select “8ΩMIN” to set the speaker impedance to 8 Ω .
• Select “6ΩMIN” to set the speaker impedance to 6 Ω .
SPEAKER | Speaker | Impedance level | |
IMP. | |||
|
| ||
|
|
| |
|
| The impedance of each | |
| Front | speaker must be 8 Ω or | |
|
| higher. | |
8ΩMIN |
|
| |
Center |
| ||
|
| The impedance of each | |
|
| ||
| Surround | speaker must be 8 Ω or | |
|
| higher. | |
| Surround back | ||
|
| ||
|
|
| |
|
| The impedance of each | |
| Front | speaker must be 4 Ω or | |
|
| higher. | |
6ΩMIN |
|
| |
Center |
| ||
|
| The impedance of each | |
|
| ||
| Surround | speaker must be 6 Ω or | |
|
| higher. | |
| Surround back | ||
|
| ||
|
|
|
■User presets USER PRESET
Use this feature to reset all the parameters of this unit to the initial factory settings (see page 122).
Choices: CANCEL, RESET
•Select “CANCEL” not to reset any parameters of this unit.
•Select “RESET” to reset the parameters of this unit.
Notes
•This setting completely resets all the parameters of this unit including the “SET MENU” parameters. However, the advanced setup menu parameters will not be initialized.
•The initial factory settings are activated next time you turn on this unit.
■Remote sensor REMOTE SENSOR
Use this feature to activate or deactivate the signal- receiving capability of the remote control sensor on the front panel of this unit.
Choices: ON, OFF
• Select “ON” if you want to activate the signal- receiving capability of the remote control sensor.
• Select “OFF” if you want to deactivate the signal- receiving capability of the remote control sensor.
Note
We recommend setting the parameter to “ON” in most cases.
ADVANCED SETUP
■Wake on RS-232C access
WAKE ON RS232C
Use this feature to set this unit to transmit data via the RS- 232C interface when this unit is in the standby mode. Choices: YES, NO
Initial setting:
[U.S.A. and Canada models]: YES
[Other models]: NO
•Select “YES” to set this unit to transmit data via the
•Select “NO” to set this unit not to transmit data via the
■Remote control AMP ID
RC AMP ID
Use this feature to set the AMP ID of this unit for remote control recognition (see page 97).
Choices: ID1, ID2
•Select “ID1” when the remote control AMP ID library code is set to “2001”.
•Select “ID2” when the remote control AMP ID library code is set to “2002”.
Note
You need to set the corresponding remote control AMP library code for the remote control (see page 97).
■Remote control TUNER ID
RC TUNER ID
Use this feature to set the TUNER ID of this unit for remote control recognition (see page 114).
Choices: ID1, ID2
•Select “ID1” when the remote control TUNER ID library code is set to “2602”.
•Select “ID2” when the remote control TUNER ID library code is set to “2603”.
Note
You need to set the corresponding remote control TUNER library code for the remote control (see page 114).
■Tuner frequency step TUNER FRQ STEP
(Asia and General models only)
Use this feature to set the tuner frequency step according to the frequency spacing in your area.
Choices: AM10/FM100, AM9/FM50
•Select “AM10/FM100” for North, Central and South America.
•Select “AM9/FM50” for all other areas.
OPERATION | ADVANCED |
|
|
English
