TROUBLESHOOTING
■Remote control
Problem | Cause | Remedy | See | |
page | ||||
|
|
| ||
The remote control | Wrong distance or angle. | The remote control will function within a maximum |
| |
does not work or |
| range of 6 m and no more than 30 degrees | 9 | |
function properly. |
| from the front panel. |
| |
|
|
|
| |
| Direct sunlight or lighting (from an | Reposition this unit. |
| |
| inverter type of fluorescent lamp, etc.) is |
| — | |
| striking the remote control sensor of this |
| ||
|
|
| ||
| unit. |
|
| |
|
|
|
| |
| The batteries are weak. | Replace all batteries. | 9 | |
|
|
|
| |
| The operation mode selector is set | Set the operation mode selector correctly. |
| |
| incorrectly. | When operating this unit, set it to the AMP position. |
| |
|
| When operating the component selected by the input | — | |
|
| selector button, set it to the SOURCE position. | ||
|
|
| ||
|
| When operating the TV set in the DTV or PHONO |
| |
|
| area, set it to the TV position. |
| |
|
|
|
| |
| The remote control code was not correctly | Set the remote control code correctly using |
| |
| set. | “LIST OF REMOTE CONTROL CODES” at the end | 96 | |
|
| of this manual. |
| |
|
|
|
| |
|
| Try setting another code of the same manufacturer |
| |
|
| using “LIST OF REMOTE CONTROL CODES” at | 96 | |
|
| the end of this manual. |
| |
|
|
|
| |
| The library code of the remote control and | Match the remote control ID of this unit with the |
| |
| the remote control ID of this unit do not | corresponding remote control library code. | 97, 111 | |
| match. |
|
| |
|
|
|
| |
| Even if the remote control code is | Program the necessary functions independently into |
| |
| correctly set, there are some models that | the programmable buttons using the Learn feature. | 98 | |
| do not respond to the remote control. |
|
| |
|
|
|
| |
The remote control | The batteries of this remote control and/or | Replace the batteries. | 9 | |
does not learn new | the other remote control are too weak. |
| ||
|
| |||
functions. |
|
|
| |
The distance between the two remote | Place the remote controls at the proper distance. | 98 | ||
| ||||
| controls is too much or too little. |
| ||
|
|
| ||
|
|
|
| |
| The signal coding or modulation of the | Learning is not possible. |
| |
| other remote control is not compatible |
| — | |
| with this remote control. |
|
| |
|
|
|
| |
| Memory capacity is full. | Delete other unnecessary functions to make room for | 103 | |
|
| the new functions. | ||
|
|
| ||
|
|
|
| |
■ HDMI |
|
|
|
Error message | Cause | Remedy | See | |
page | ||||
|
|
| ||
|
|
|
| |
DEVICE OVER | The number of the connected HDMI | Reduce the number of the connected HDMI | — | |
components is over the limit. | components. | |||
|
| |||
|
|
|
| |
HDCP ERROR | HDCP authentication failed. | Check that the connected HDMI components support | — | |
the HDCP copy protection standards. | ||||
|
|
| ||
|
|
|
|
INFORMATION | ADDITIONAL |
|
|
English
