113 En, Setting remote control tuner ID | Yamaha RX-V1700 manual

4Press the numeric buttons to enter the four-digit remote control code for the input area you want to use.

CLASSICAL LIVE/CLUB ENTERTAIN MOVIE

1 2 3 4

STEREO SUR. DECODE SELECT EXTD SUR.

5 6 7 8

90

Remote control AMP codes

Select one of the following codes to set the remote control AMP code for the input area you want to use.

	AMP library		Remote
	code		Remote
	code	Function	control AMP
	(remote control	Function	control AMP
	(remote control		ID
	setting)		ID
	setting)

	2001	To operate this unit using the	ID1
	(initial setting)	default code.	(initial setting)

	2002	To operate this unit using an	ID2
	2002	alternative code.	ID2
		alternative code.

Note

You need to set the corresponding remote control AMP ID (see page 111).

5Press ENTER to set the number.

“OK” appears in the display window if setting was successful.

“NG” appears in the display window if the setting was unsuccessful. In this case, start over from step 1.

PRESET/CH

ENTER

A/B/C/D/E

6Press LEARN again to exit from the setup mode.

LEARN

ADVANCED SETUP

■Setting remote control tuner ID

1Set the operation mode selector to AMP or SOURCE and then press TUNER on the remote control to select the tuner to change the remote control ID.

AMP

SOURCE

TV

TUNER

or

AMP

SOURCE

TV

2Press and hold LEARN for about 3 seconds using a ballpoint pen or similar object and the l / h repeatedly until “L;TUN” and “TUNER” appear in the display window on the remote control.

PRESET/CH

LEARN

ENTER

A/B/C/D/E

Notes

•Be sure to press and hold LEARN for at least 3 seconds, otherwise the learning process will start.

•If you do not complete each of the following steps within 30 seconds, the setting mode will be automatically canceled. In this case, start over from step 1.

3Press ENTER.

The four-digit code set for the selected input area appears in the display window on the remote control.

PRESET/CH

ENTER

A/B/C/D/E

OPERATION	ADVANCED

English

113 En

Image 115

Yamaha RX-V1700 owner manual 113 En, Setting remote control tuner ID, Remote control AMP codes, Control AMP

Contents

RX-V1700 Special Instructions for U.K. Model For U.K. customers Contents Features About this manual Supplied accessoriesGetting Started Check that you received all of the following parts Front panel Controls and Functions Opening and closing the front panel Door Return Remote controlRemote control controls and functions Level Macro PowerVolume + Macro ON/OFF Zone 2/ZONE 3 switch Zone 2/Zone 3 remote controlID1/ID2 switch Volume + Remote control sensor Approximately 6 m Preparing the remote controlInstalling batteries in the remote control Using the remote control 10 En Front panel display EON 11 EnPTY Hold Voltage Selector Rear panel12 En Wrench Holder Placing speakers Connections13 En Left Right Center speaker Connecting speakers14 En Subwoofer Surround back speakers 15 En Connecting the speaker cable Models Connecting the banana plugConnecting to the SP2 speaker Terminals 16 En Conventional connection 17 EnBi-amplification connection Video jacks Information on jacks and cable plugs18 En Audio jacks Hdmi jack and cable plug Information on Hdmi19 En Hdmi compatibility with this unit InputOutput Audio and video signal flowAudio signal flow Video signal flow 20 En 21 En Connecting a TV monitor or projector DVD player Connecting other componentsConnecting a DVD player 22 En DVD recorder, PVR or VCR Connecting a DVD recorder, PVR or VCRConnecting set-top boxes 23 En Turntable Connecting audio components24 En CD recorder 25 En Connecting an external amplifier For 8-channel input Connecting a multi-format player or an external decoder26 En For 6-channel input 27 En Using the Video AUX jacks on the front panelGame console or Video camera 28 En Connecting the AM loop antenna Asia and General models only Connecting the power cableConnecting the AC power cable 29 En 30 En Setting the speaker impedance 31 En Turning on and off the powerWhen all connections are complete, turn on this unit Front panel Remote control Omni-directional microphone Auto SetupUsing Auto Setup 32 En Automenu SET Menu33 En Resultexit Autocheck34 En 35 En ResultwiringResults of the speaker Output level If an error screen appears Error36 En If Warning appears 37 En Turn on the video monitor connected to this unit Basic procedurePlayback 38 En 39 En Guide to contents 40 En Selecting audio input jacksAuto 41 En Using your headphonesSelecting the Multi CH Input component Muting the audio output Audio information Displaying the input sourceInformation 42 En 43 En Using the sleep timerCanceling the sleep timer Playing video sources 44 En Front panel operations Remote control operationsSound Field Programs Selecting sound field programs Classical Sound field program descriptions45 En For music audio sources Entertainment 46 EnFor various sources LIVE/CLUB Movie 47 EnFor visual sources of music For movie sources Stereo playback 48 EnStereo 49 En Deactivating the Straight modeEnjoying unprocessed input sources Straight Bypassing the tone control circuitry Using Audio FeaturesEnjoying pure hi-fi sound Adjusting the tonal quality 50 En Press Parameter and then l / h to set the Direct parameter Adjusting the speaker levelEnjoying multi-channel sources in 2-channel stereo 51 En Following display is shown in the OSD Selecting the Compressed Music Enhancer modeMusic Enhancer 52 En 53 En Selecting the night listening mode Front panel functions FM/AM TuningFM/AM controls and functions 54 En 55 En Remote control functions 56 En Automatic tuning 57 En Manual tuning Seconds Automatic preset tuning58 En Press and hold Memory for more than 2,5 Manual preset tuning59 En 60 En Selecting preset stations 2,4 Exchanging preset stations61 En Frequency display Radio Data System Tuning Europe Models onlyDisplaying the Radio Data System information 62 En Control to select the desired program type Press PRESET/CH k / n on the remoteNews 63 En POP M 64 En 65 En 66 En Controlling iPod in the simple remote ModeControlling iPod in the menu browse Mode Controlling iPod Repeat Repeat 67 EnFollowing display appears in the OSD Shuffle Shuffle 68 En Recording Press h to increase the value Press l to decrease the value Advanced Sound ConfigurationsChanging sound field parameter settings 69 En INIT.DLY 70 EnSound field parameter descriptions DSP Level Room Size P.ROOM Size S.ROOM Size SB Room Size 71 EnLiveness S.LIVENESS SB Liveness REV.LEVEL REV.DELAY72 En REV.TIME Selecting decoders for 2-channel Sources surround decode modePress Select on the remote control 73 En Surround Decode 74 EnDecoder descriptions Surround Decode PRO Logic Available decoders 75 EnSelecting decoders used with sound Field programs Decoder parameter descriptions Decoders 76 EnSelecting decoders for multi-channel Sources Auto Auto 77 En Customizing this Unit Manual SetupAuto setup Auto Setup Manual setup Manual Setup 78 En Signal information Signal Info 79 En Using SET MenuPress k / n to select Manual Setup Press Enter to enter Manual Setup LFE/BASS OUT Speaker settings Aspeaker SETBlfe Level Basic Menu Speaker Center SP81 En Center speaker Center SP Priority 02ASUBWOOFER PhasePresence SP Cross Over Speaker level BSP Level BSP LevelCSP Distance 83 En Equalizer select Select Dtest ToneAequalizer 84 En 85 En Cdynamic RangeLow-frequency effect level 86 En Audio settings Daudio SETDaudio SET Ehdmi SET Input/output assignment CMPNT-V InputCoaxial 87 En 88 En Optical OUTHdmi Cinput Rename Emulti CH SET Cvolume TrimDdecoder Mode Multi channel input Setup Adisplay SET Display settings Adisplay SET90 En 91 En 92 En Bmemory GuardCaudio Select EPARAM. INI Gdock SET Fzone SET93 En Controlling this unit Remote Control FeaturesControlling this unit, a TV, or other components 94 En Controlling other components 95 En 96 En Setting remote control codesControlling optional components Option mode Remote control code default settings Press Enter to set the number Press Learn again to exit from the setup mode97 En Press Enter 98 En Remote controls 99 En Press Learn again to exit the learning modePress Rename using a ballpoint pen or similar object Changing source names in the display window 100 En Macro programming featuresMacro operations 101 En Default macro functionsFirst Second Third Programming macro operations 102 En Clearing function sets Clearing configurationsPress k / n to select the clear mode 103 En Press Learn again to exit 104 EnClearing a learned function Selected component name appears in the display window 105 En Press Macro again to exit the macro programming modeClearing a macro function 106 En Using MULTI-ZONE ConfigurationConnecting the Zone 2 and Zone 3 components Using external amplifiers Selecting Zone 2 or Zone Using the internal amplifiers of this unitControlling Zone 2 or Zone 107 En Selecting the input source of Zone 2 or Zone 108 En Adjusting the tonal quality of Zone 2 or Zone Adjusting the volume level of Zone 2 or Zone109 En Using Advanced Setup Advanced Setup110 En 111 En 112 En Setting remote control IDVideo reset Video Reset Setting remote control AMP ID 113 En Setting remote control tuner IDRemote control AMP codes OK appears in the display window if setting was successful Tuner ID Remote control tuner codes114 En Control 115 En TroubleshootingGeneral 116 En 117 En Tuner 118 En Device Over Remote controlHdcp Error 119 En 120 En Before Auto SetupIPod After Auto Setup During Auto Setup121 En 122 En Resetting the System 123 En Glossary 124 En 125 En Video signalSampling frequency and number Quantized bits Sound output from each speaker Sound Field Program Information126 En Elements of a sound field Factor Parametric Equalizer Information127 En Frequency 128 En Specifications General 129 En APPENDIX-i Sound Output in Each Sound Field Program Channel audio 6.1-channel Monaural Stereo APPENDIX-iiAudio *2 Audio *3 Surround Decode APPENDIX-iii APPENDIX-iv DVD Player APPENDIX-vCable CD Player CD Recorder APPENDIX-vi APPENDIX-vii VCR APPENDIX-viii WH63590