Makita RBC411 instruction manual Mounting of protector

Page 10

Mounting of protector

To meet the applicable safety provisions, only the tool/protector combinations as indicated in the table must be used.

Be sure to use genuine MAKITA cutter blade or nylon cutting head.

–The cutter blade must be well polished, free of cracks or breakage.

–If the cutter blade hits against a stone during operation, stop the engine and check the blade immediately.

–Polish or replace the cutter blade every three hours of operation.

–The outside diameter of the cutter blade must be 255 mm (10-1/32”). Never use any blades surpassing 255 mm (10-1/32”) in outside diameter.

Star Blade	Eddy Blade	Saw Blade	Protector for metal blade
PART NO. 6418501400	PART NO. 6418501900	PART NO. 6418501600	PART NO. 6418026000

CAUTION: The appropriate protector must always be installed, for your own safety and in order to comply with accident-prevention regulations. Operation of the equipment without the guard being in place is not permitted.

– Fix the protector (1) to the clamp (3) with two bolts M6 x 30 (2).

NOTE: Tighten the right and left bolts evenly so that the gap between the clamp

(3) and the protector (1) will be constant.

Otherwise, the protector sometimes may not function as specified.

10

Image 10

Contents Importante Symbols Table of ContentsPersonal protective equipment Safety instructionsGeneral Instructions Starting up the brush cutterPage Kickback RefuellingMethod of operation Kickback preventionCutting Tools Maintenance instructionsNever straighten or weld damaged cutting tools Technical data Model RBC411Designation of parts Assembly of engine and shaft Mounting of handleMounting of protector Mounting of cutter blade Mounting of cutter bladeHandling petroleum products Fuels/refuelingFuel and oil mixture Attachment of shoulder strap Correct handling of machineDetachment Starting the warm engine Putting into operationCold start StoppingResharpening the cutting tool Checking the Idling speedMaintenance schedule Fault location StorageSímbolos Índice PáginaEquipamentos de proteção pessoal Instruções de segurançaInstruções gerais Colocação do cortador de mato em funcionamentoPage Rebote ReabastecimentoMétodo de operação Prevenção de reboteNunca regule ou solde ferramentas de corte danificadas Ferramentas de corteInstruções de manutenção Cabeçote de corte de náilonDados técnicos Modelo RBC411Designação de peças Montagem do motor e eixo Montagem do punhoMontagem do protetor Montagem do disco do cortador Montagem do disco do cortadorManuseio de produtos de petróleo Combustíveis/abastecimentoMistura de combustível e óleo Fixação da alça de ombro Correto manuseio da máquinaRemoção Cuidado durante a operação Colocação em funcionamentoInício frio Início do aquecimento do motorAfiação da ferramenta de corte Verificando a velocidade em marcha lentaProgramação de manutenção Armazenamento Localização de falhaEspañol Equipo protector personal Instrucciones de seguridadInstrucciones generales Arranque de la desbrozadoraPage Retroceso brusco Reabastecimiento de combustibleMétodo de operación Prevención de retrocesos bruscosCabeza cortadora de nailon Herramientas de corteInstrucciones de mantenimiento Disco de sierraInformación técnica Identificación de las piezas Ensamblado del motor y astil Colocación del mangoColocación del protector Colocación del disco cortador Colocación del disco cortadorManejo de sustancias del petróleo Combustible / reabastecimientoMezcla de combustible y aceite Colocación de la correa de hombro Manejo correcto del equipoDesprendimiento Precaución durante la operación Activación del equipoArranque en frío Arranque con el motor ya calentadoReafilado de la pieza de corte Revisión de la velocidad en estado pasivoPrograma de mantenimiento ApagadoAlmacenamiento FallasSymboles Table des matièresDispositifs de protection individuelle Instructions de sécuritéInstructions générales Démarrage de la débroussailleusePage Choc en retour Mode d’emploiFaire le plein d’essence MètresTête à fils de nylon Outils de coupeInstructions d’entretien Lame en étoile 4 dents, en tourbillon 8 dentsCaractéristiques techniques Modèle RBC411Nomenclature des pièces Montage du moteur et de l’arbre Montage de la poignéeMontage du dispositif de protection MakitaMontage de la lame Montage de la lameManipulation de produits pétrolifères Carburants/pleinMélange d’huile et d’essence Fixation de la bandoulière Maniement correct de l’outilDétachement Démarrage à chaud Mise en marcheDémarrage à froid ArrêtRéaffûtage de l’outil de coupe Vérification de la vitesse du ralentiProgramme d’entretien Entreposage Détection des pannesPage Page Makita Corporation