Makita RBC411 instruction manual Resharpening the cutting tool, Checking the Idling speed

Page 15

IDLE ADJUSTMENT

The cutter blade or the nylon cutting head should not run when the control lever is fully released. If necessary, adjust the idle rpm using the idle adjusting screw.

Checking the Idling speed

–Idle speed should be set to 2,600 /min.

If necessary correct it by means of the idle screw (the blade or the nylon cutting head must not turn when the engine is at idle).

Screwing in the screw (1) will cause an increase in the engine speed, whereas backing off the screw will reduce the engine speed.

Resharpening the cutting tool

CAUTION: The cutting tools mentioned below must only be resharpened by an authorized facility. Manual resharpening will result in imbalances of the cutting tool causing vibrations and damage to the equipment.

– cutter blade (star blade (4 teeth), eddy blade (8 teeth), saw blade)

An expert resharpening and balancing service is provided by Authorized Service Agents.

NOTE: To increase the service life of the cutter blade (star blade, eddy blade, saw blade) it may be turned over once, until both cutting edges have become blunt.

15

Image 15

Contents Importante Table of Contents SymbolsStarting up the brush cutter Safety instructionsGeneral Instructions Personal protective equipmentPage Kickback prevention RefuellingMethod of operation KickbackMaintenance instructions Cutting ToolsNever straighten or weld damaged cutting tools Model RBC411 Technical dataDesignation of parts Mounting of handle Assembly of engine and shaftMounting of protector Mounting of cutter blade Mounting of cutter bladeFuels/refueling Handling petroleum productsFuel and oil mixture Correct handling of machine Attachment of shoulder strapDetachment Stopping Putting into operationCold start Starting the warm engineChecking the Idling speed Resharpening the cutting toolMaintenance schedule Storage Fault locationÍndice Página SímbolosColocação do cortador de mato em funcionamento Instruções de segurançaInstruções gerais Equipamentos de proteção pessoalPage Prevenção de rebote ReabastecimentoMétodo de operação ReboteCabeçote de corte de náilon Ferramentas de corteInstruções de manutenção Nunca regule ou solde ferramentas de corte danificadasModelo RBC411 Dados técnicosDesignação de peças Montagem do punho Montagem do motor e eixoMontagem do protetor Montagem do disco do cortador Montagem do disco do cortadorCombustíveis/abastecimento Manuseio de produtos de petróleoMistura de combustível e óleo Correto manuseio da máquina Fixação da alça de ombroRemoção Início do aquecimento do motor Colocação em funcionamentoInício frio Cuidado durante a operaçãoVerificando a velocidade em marcha lenta Afiação da ferramenta de corteProgramação de manutenção Localização de falha ArmazenamentoEspañol Arranque de la desbrozadora Instrucciones de seguridadInstrucciones generales Equipo protector personalPage Prevención de retrocesos bruscos Reabastecimiento de combustibleMétodo de operación Retroceso bruscoDisco de sierra Herramientas de corteInstrucciones de mantenimiento Cabeza cortadora de nailonInformación técnica Identificación de las piezas Colocación del mango Ensamblado del motor y astilColocación del protector Colocación del disco cortador Colocación del disco cortadorCombustible / reabastecimiento Manejo de sustancias del petróleoMezcla de combustible y aceite Manejo correcto del equipo Colocación de la correa de hombroDesprendimiento Arranque con el motor ya calentado Activación del equipoArranque en frío Precaución durante la operaciónRevisión de la velocidad en estado pasivo Reafilado de la pieza de corteApagado Programa de mantenimientoFallas AlmacenamientoTable des matières SymbolesDémarrage de la débroussailleuse Instructions de sécuritéInstructions générales Dispositifs de protection individuellePage Mètres Mode d’emploiFaire le plein d’essence Choc en retourLame en étoile 4 dents, en tourbillon 8 dents Outils de coupeInstructions d’entretien Tête à fils de nylonModèle RBC411 Caractéristiques techniquesNomenclature des pièces Montage de la poignée Montage du moteur et de l’arbreMakita Montage du dispositif de protectionMontage de la lame Montage de la lameCarburants/plein Manipulation de produits pétrolifèresMélange d’huile et d’essence Maniement correct de l’outil Fixation de la bandoulièreDétachement Arrêt Mise en marcheDémarrage à froid Démarrage à chaudVérification de la vitesse du ralenti Réaffûtage de l’outil de coupeProgramme d’entretien Détection des pannes EntreposagePage Page Makita Corporation