American Power Conversion 250 A manual Display Interface

Page 39

Display Interface

Overview

The ATS display interface is used to configure settings, set alarm thresholds, and provide audible and visual alarms.

Load

On

Check

Log

Gen Set On

Alarm

ESC

?

   

  

 

 

 

 

 

 

Load On LED

 

When lit green, all output phases are within the limits

 

 

 

 

specified by the output alarm limit thresholds.

 

 

 

 

 

 

Check Log LED

 

When lit yellow, at least one new alarm condition has

 

 

 

 

been detected.

 

 

 

 

 

 

 

Gen Set On LED

 

When lit green, the generator is running.

 

 

 

 

 

 

 

 

Alarm LED

 

When lit red, an alarm condition exists.

 

 

 

 

 

 

 

LCD

 

For viewing alarms, status data, instructional help, and

 

 

 

 

configuration items.

 

 

 

 

 

 

 

Up and Down

 

Selects menu items and accesses information.

 

 

navigation buttons

 

 

 

 

 

 

 

 

 

 

 

 

ENTER button

 

Opens menu items and inputs changes to system

 

 

 

 

parameters.

 

 

 

 

 

 

 

HELP button

 

Launches context-sensitive help. Press the HELP button

 

 

 

 

for information about each item on the screen and for

 

 

 

 

instructions about performing certain tasks.

 

 

 

 

 

 

 

ESC button

 

Returns to previously displayed screen.

 

 

 

 

 

 

 

InfraStruXure Power Generation System

29

Image 39
Contents Operation Page Companion manuals How to find updates to this manualAbout This Manual AudiencePage Contents Display Interface Communication Configuration Customizing and Updating the ATS Specifications Page Safety symbols used in this manual Cross-reference symbols used in this manualOverview Wire sizing Installation Total power off procedureOperating environment Page Overview InfraStruXure Power Generation SystemSystem Operates How the InfraStruXure Power GenerationGenerator cool-down Generator start sequenceOpen and closed transfers Fuel monitoring/runtime calculation Page Front view, door closed Smart Distribution Panel with ATS The automatic operation Control panel is used to set Front view, door openATS panel board, left side Installation Manual for instructionsATS panel board, right side ATS Component Details Motorized switchesUser connection plate Automatic operation control panelATS monitoring unit  When the EPO Arm/Test rocker is in the TestATS label kit Automatic Operation OperationAutomatic Operation Problem-loss of automatic operation Emergency Manual Operation Set the ATS Automatic Operation switch to Disable How to power the load from the generatorEmergency Manual Operation How to return to powering the load from utility Press Total Power Off Total Power Off Display Interface Top-level menu screen Top-level status screensNavigating through screens Password-protected screensTotal Load Summary Total Load by PhasePower Factor Load-MeterATS/Voltage ATS PositionS1-Utility S2-Generator ATS Setup ATS/Voltage Generator Status GeneratorOperating Settings Gen Output AdjustManufacturer Data Testing View Test LogRun/View Test Test Duration Test ScheduleHow a test occurs Reset Reset AllStats Alarm Setup AlarmsView Active Alarms Alarm/Event LogOther Limits Alarm BeeperClearing latched alarms Fuel Alarm LimitsDate/Time ConfigSystem Password System/NetworkPage Reset 100% Fuel Level Electrical ConfigFactory Defaults Firmware UpdatesPage Network management interfaces ATS Management OptionsOverview InfraStruXure ManagerConnect the ATS to the InfraStruXure Manager Configuring the InfraStruXure ManagerConnect the ATS to your network Configuring the ATS Network Management InterfaceConfiguration overview TCP/IP configuration methodsDevice IP Configuration Wizard Bootp & Dhcp configuration Option 43 = 01 04 31 41 50 43 where Remote access to the control console Local access to the control consoleChoose Network from the Control Console menu Control consoleWeb interface How to Access the ATS Network Management InterfaceSnmp Telnet and SSHFTP and SCP InfraStruXure Power Generation System Customizing and Updating the ATS How to connect contacts to the user interface board EPO Test NC no How to Connect an EPO Switch to the ATSContact Closure-Normally Open Problem Action Safety warnings How to Allow Easy Access to the ATS Display Interface Part Number Description Height on Panel Output distribution circuit breakers available from APCCircuit breaker adapter modules available from APC Determine the configuration of the panelCombination #1 Allowed circuit breaker combinationsCombination #6 T1 three-pole breaker requires no additional preparation Preparing the breakers for installationT1 three-pole breaker assembly Parts and tools needed for installation proceduresInstalling breakers on the ATS panel bus See also From a local computer How to Download Firmware UpdatesPhysical ElectricalAWG Installation and Wiring 208V 480VCompliance EnvironmentalPage If Source 2 is a Second Utility Appendix Custom InstallationsInfraStruXure Power Generation System Index InfraStruXure Power Generation System InfraStruXure Power Generation System Page Page Page Radio Frequency Interference 990-1845C