American Power Conversion 250 A manual Configuration overview, TCP/IP configuration methods

Page 62

Configuring the ATS Network Management Interface

Configuration overview

You must configure the following TCP/IP settings before the ATS can operate on a network:

IP address of the ATS (only needed for manual address assignment)

Subnet mask

Default gateway

Note

If a default gateway is unavailable, use the IP address of a usually running computer that is located on the same subnet as the ATS. The ATS will use the default gateway to test the network at times when traffic is very light. Refer to “Watchdog Features” in the “Introduction” of the InfraStruXure Power Generation System’s on-line Network Management User’s Guide for more information about the watchdog role of the default gateway.

TCP/IP configuration methods

Use one of the following methods to define the TCP/IP settings needed by the ATS:

Device IP Configuration Wizard (see “Device IP Configuration Wizard” on this page).

BOOTP or DHCP server (see “BOOTP & DHCP configuration” on page 53).

Local computer (see “Local access to the control console” on page 55).

Networked computer (see “Remote access to the control console” on page 55).

Device IP Configuration Wizard

You can use the Device IP Configuration Wizard on a Windows NT®, Windows 2000, or Windows XP computer to discover unconfigured ATS systems and configure their basic TCP/IP settings.

To configure one or more ATSs by exporting configuration settings from a configured ATS, refer to “How to Export Configuration Settings” in the on-line Network

See also Management User’s Guide on the Utility CD.

1.Insert the InfraStruXure Power Generation System’s Utility CD into a computer on your network.

2.Launch the Wizard, when prompted. If prompted to restart the computer, access the Wizard from the Start menu after the computer has restarted.

3.Wait for the Wizard to discover the first unconfigured ATS, then follow the on-screen instructions.

If the Start a Web browser when finished option is enabled, you can use apc for both the User Name and the Password to access the ATS through your browser.

Note

52

InfraStruXure Power Generation System

Image 62
Contents Operation Page Audience How to find updates to this manualAbout This Manual Companion manualsPage Contents Display Interface Communication Configuration Customizing and Updating the ATS Specifications Page Overview Safety symbols used in this manualCross-reference symbols used in this manual Wire sizing Operating environment InstallationTotal power off procedure Page InfraStruXure Power Generation System OverviewHow the InfraStruXure Power Generation System OperatesGenerator start sequence Generator cool-downOpen and closed transfers Fuel monitoring/runtime calculation Page Smart Distribution Panel with ATS Front view, door closedFront view, door open  The automatic operation Control panel is used to setInstallation Manual for instructions ATS panel board, left sideATS panel board, right side Motorized switches ATS Component DetailsAutomatic operation control panel User connection plate When the EPO Arm/Test rocker is in the Test ATS monitoring unitATS label kit Operation Automatic OperationAutomatic Operation Problem-loss of automatic operation Emergency Manual Operation How to power the load from the generator Set the ATS Automatic Operation switch to DisableEmergency Manual Operation How to return to powering the load from utility Press Total Power Off Total Power Off Display Interface Top-level status screens Top-level menu screenPassword-protected screens Navigating through screensLoad-Meter Total Load by PhasePower Factor Total Load SummaryS1-Utility ATS/VoltageATS Position S2-Generator ATS Setup ATS/Voltage Generator Generator StatusManufacturer Data Operating SettingsGen Output Adjust Run/View Test TestingView Test Log Test Schedule Test DurationHow a test occurs Stats ResetReset All Alarm/Event Log AlarmsView Active Alarms Alarm SetupFuel Alarm Limits Alarm BeeperClearing latched alarms Other LimitsSystem/Network ConfigSystem Password Date/TimePage Firmware Updates Electrical ConfigFactory Defaults Reset 100% Fuel LevelPage InfraStruXure Manager ATS Management OptionsOverview Network management interfacesConfiguring the InfraStruXure Manager Connect the ATS to the InfraStruXure ManagerConfiguring the ATS Network Management Interface Connect the ATS to your networkDevice IP Configuration Wizard Configuration overviewTCP/IP configuration methods Bootp & Dhcp configuration Option 43 = 01 04 31 41 50 43 where Local access to the control console Remote access to the control consoleControl console Choose Network from the Control Console menuHow to Access the ATS Network Management Interface Web interfaceTelnet and SSH SnmpFTP and SCP InfraStruXure Power Generation System Customizing and Updating the ATS How to connect contacts to the user interface board How to Connect an EPO Switch to the ATS EPO Test NC noContact Closure-Normally Open Problem Action Safety warnings How to Allow Easy Access to the ATS Display Interface Output distribution circuit breakers available from APC Part Number Description Height on PanelDetermine the configuration of the panel Circuit breaker adapter modules available from APCAllowed circuit breaker combinations Combination #1Combination #6 Preparing the breakers for installation T1 three-pole breaker requires no additional preparationParts and tools needed for installation procedures T1 three-pole breaker assemblyInstalling breakers on the ATS panel bus See also How to Download Firmware Updates From a local computerElectrical PhysicalInstallation and Wiring 208V 480V AWGEnvironmental CompliancePage Appendix Custom Installations If Source 2 is a Second UtilityInfraStruXure Power Generation System Index InfraStruXure Power Generation System InfraStruXure Power Generation System Page Page Page Radio Frequency Interference 990-1845C