Texas Instruments TMS320 specifications Read, Output disable, ROM protection and verification

Page 62

TMS320E25

SPRS010B Ð MAY 1987 Ð REVISED NOVEMBER 1990

ADVANCE INFORMATION

Program

A12-A0

Verify

VIH

Address Stable

Address N + 1

VIL

Q8-Q1

VIH/VOH

Data In Stable

HI-Z

Data Out Valid

VIL/VOL

VPP

VPP

VCC

VCC

VCC + 1

VCC

VIH

E

VIL

VIH

PGM

VIL

VIH

G

VIL

Figure 11. Fast Programming Timing

program inhibit

Programming may be inhibited by maintaining a high level input on the E pin or PGM pin.

read

The EPROM contents may be read independent of the programming cycle, provided the RBIT (ROM protect bit) has not been programmed. The read is accomplished by setting E to zero and pulsing G low. The contents of the EPROM location selected by the value on the address inputs appear on Q8-Q1.

output disable

During the EPROM programming process, the EPROM data outputs may be disabled, if desired, by establishing the output disable state. This state is selected by setting the G and PGM pins high. While output disable is selected, Q8-Q1 are placed in the high-impedance state.

ROM protection and verification

This section describes the code protection feature included in the EPROM cell, which protects code against copyright violations. Table 6 shows the programming levels required for protecting and verifying the EPROM. The paragraphs following the table describe the protect and verify functions.

62	POST OFFICE BOX 1443 • HOUSTON, TEXAS 77001

Image 62

Contents TMS320 SECOND-GENERATION Digital Signal Processors DescriptionFunction PIN Signals DefinitionPGA and PLCC/CER-QUAD PIN Assignments Introduction Memory Space Key Features TMS32020Bit-Reversed Indexed-Addressing Mode for Wait States for Communication to Slower Off-ChipPackage ArchitectureTMS320 Second-Generation Device Overview TypeFunctional block diagram TMS320C2x SECOND-GENERATION Devices16 ⋅ 16-bit parallel multiplier TimerScaling shifter Memory controlTMS320 SECOND-GENERATION Devices Memory MapsMultiprocessing Interrupts and subroutinesExternal interface Addressing modes Repeat featureInstruction set Instruction set summary Instruction SymbolsSymbol Definition TMS320C25 Instruction Set Summary XORK² SUBT²XOR ZACLTA ApacLPH ² LTP ²Data Memory Operations Mnemonic Description Words TMS320C25 Instruction Set Summary concluded TMS32020 TMS32020 Product NotificationDevelopment support Hardware Tools Part Number TMS320 Second-Generation Software and Hardware SupportSoftware Tools Part Number Specification overview Documentation supportParameter Test Conditions MIN TYP§ MAX Unit Recommended operating conditionsMIN NOM MAX Unit External clock option Clock Characteristics and TimingInternal clock option Test Load Circuit Memory and Peripheral Interface Timing Parameter MIN TYP MAX UnitHold Holda RS, INT, BIO, and XF TimingHold Timing Serial Port Timing TMS320C25GBA INT Clkin / Clkx / ClkrMP/MC IOH Parameter Test Conditions MIN TYP MAX Unit External Clock Option ClkinVOH Min TdC1L-AL Low after CLKOUT1 low Serial Port Timing VPP Eprom ProgrammingSee Notes 14 IPP1MP/MC VIL INT0 INT2 VIHCLKIN, CLKX, Clkr Internal Clock Option External clock option CLKOUT1, CLKOUT2Fcrystal TdC1-S From Clkout if Is present TsuIN Setup before CLKOUT1 high Parameter Contrast Summary of Electrical SpecificationsClock characteristics and timing MIN TYP MAXHold timing Memory and peripheral interface timingRS, INT, BIO, and XF timing Serial port timingTiming Diagrams Clock timingReady Memory read timingBR, PS, D S Memory write timing CLKOUT1 CLKOUT2 StrbOne wait-state memory access timing MSCReset timing IackInterrupt timing TMS32020 Interrupt timing TMS320C25Serial port receive timing Serial port transmit timingBIO timing External flag timingPC = N PC = N + Holda Hold timing part aHold ExecuteHolda Fetch Hold timing part BCLKOUT1 CLKOUT2 Fetch Execute Or is D15-D0 TdHH-AH Typical Supply Current Characteristics for TMS320C25 TMS320C25FNL Plcc reflow soldering precautionsParameter MAX Unit Mechanical DataPin GB grid array ceramic package TMS32020, TMS320C25 Advance Jedec NO. Outline Terminals MIN MAX Programming the TMS320E25 Eprom cell Fast programming and verificationEPT Pin Nomenclature TMS320E25VCC EPT VPPProgram Read Output Name ² PIN Verify Inhibit Disable TMS320E25 Programming Mode LevelsSignal ErasureFast Programming Flowchart Program verifyROM protection and verification Output disableRead VIH VIL PGM VPP VCC TMS320E25 Protect and Verify Eprom Mode LevelsEprom protect VSS Clkin EPT VPPEprom RbitVIH VIL VPP VCC VCC VIH VIL PGM VIH/VOH HI-Z VIL/VOL VPP EPT VSSTMS320 SECOND-GENERATION NIL Packaging Information Other Qualified Versions of TMS320C25Important Notice