Texas Instruments TMS320 specifications Recommended operating conditions, MIN NOM MAX Unit

TMS32020

SPRS010B Ð MAY 1987 Ð REVISED NOVEMBER 1990

absolute maximum ratings over specified temperature range (unless otherwise noted)²

Supply voltage range, VCC³	. ± 0.3	V to 7 V
Input voltage range	. ± 0.3	V to 7 V
Output voltage range	. ± 0.3	V to 7 V
Continuous power dissipation	. . . . . . . .	. . 2 W
Operating free-air temperature range	. . . 0°C to 70°C
Storage temperature range	± 55°C to 150°C

²Stresses beyond those listed under ªAbsolute Maximum Ratingsº may cause permanent damage to the device. This is a stress ratingonly, and functional operation of the device at these or any other conditions beyond those indicated in the ªRecommended Operating Conditionsº section of

this specification is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. ³ All voltage values are with respect to VSS.

recommended operating conditions

			MIN	NOM	MAX	UNIT
VCC	Supply voltage		4.75	5	5.25	V
VSS	Supply voltage			0		V
VIH	High-level input voltage	All inputs except CLKIN	2	VCC + 0.3		V
		CLKIN	2.4	VCC + 0.3		V
VIL	Low-level input voltage	All inputs except CLKIN	± 0.3		0.8	V
		CLKIN	± 0.3		0.8	V
IOH	High-level output current				300	∝A
IOL	Low-level output current				2	mA
TA	Operating free-air temperature (see Notes 1 and 2)		0		70	°C

NOTES: 1. Case temperature (TC) must be maintained below 90°C. 2. RθJA = 36°C/Watt, RθJC = 6°C/Watt.

electrical characteristics over specified free-air temperature range (unless otherwise noted)

	PARAMETER	TEST CONDITIONS	MIN	TYP§	MAX	UNIT
VOH	High-level output voltage	VCC = MIN, IOH = MAX	2.4	3		V
VOL	Low-level output voltage	VCC = MIN, IOL = MAX		0.3	0.6	V
IZ	Three-state current	VCC = MAX	±20		20	∝A
II	Input current	VI = VSS to VCC	±10		10	∝A
		TA = 0°C, VCC = MAX, fx = MAX			360	mA
ICC	Supply current	TA = 25°C, VCC = MAX, fx = MAX		250		mA
		TC = 90°C, VCC = MAX, fx = MAX			285	mA
CI	Input capacitance				15	pF
CO	Output capacitance				15	pF

§ All typical values for ICC are at VCC = 5 V, TA = 25°C.

ADVANCE INFORMATION

This device contains circuits to protect its inputs and outputs against damage due to high static voltages or electrostatic fields. These circuits have been qualified to protect this device against electrostatic discharges (ESD) of up to 2 kV according to MIL-STD-883C, Method 3015; however, it is advised that precautions should be taken to avoid application of any voltage higher than maximum-rated voltages to these high-impedance circuits. During storage or handling, the device leads should be shorted together or the device

should be placed in conductive foam. In a circuit, unused inputs should always be connected to an appropriated logic voltage level, preferably either VCC or ground. Specific guidelines for handling devices of this type are contained in the publication Guidelines for Handling Electrostatic-Discharge-Sensitive (ESDS) Devices and Assemblies available from Texas Instruments.

POST OFFICE BOX 1443 • HOUSTON, TEXAS 77001 21