RIDGID K6200 Maintenance Instructions, Machine Storage Service and Repair, Autofeed Assembly

Page 15

K-6200 Drain Cleaning Machine

Figure 16 – Lifting Hook

Maintenance Instructions

WARNING

Make sure machine is unplugged from power source before performing maintenance or making any ad- justment.

Autofeed Assembly

Proper cleaning and lubrication of the autofeed is advised for long, trouble-free operation. After each use, hose out autofeed with water and grease bearings.

Lubrication

Grease all exposed, moving and rotating parts as re- quired. A grease fitting is provided for the drum front and rear bearings.

Cables

Drain drum after every use. Flush drum periodically, re- move sediment that can corrode cable.

Cables should be thoroughly flushed with water to prevent damaging effects of drain cleaning compounds.

Periodically lubricate cables and couplings with RIDGID Cable Rust Inhibitor.

When not in use, store cables indoors to prevent deteri- oration by the elements.

Cables should be replaced when they become severely corroded or worn. A worn cable can be identified when outside coils of cable become flat or lose their rigidity.

Machine Storage

WARNING Motor-driven equipment must be kept in- doors or well covered in rainy weather. Store the machine in a locked area that is out of reach of children and peo- ple unfamiliar with drain cleaners. This machine can cause serious injury in the hands of untrained users.

Service and Repair

WARNING

The “Maintenance Instructions” will take care of most of the service needs of this machine. Any problems not addressed by this section should only be handled by an authorized RIDGID service technician.

Tool should be taken to a RIDGID Independent Auth- orized Service Center or returned to the factory. All repairs made by Ridge service facilities are warranted against de- fects in material and workmanship.

WARNING When servicing this machine, only identi- cal replacement parts should be used. Failure to follow these instructions may create a risk of electrical shock or other serious injury.

If you have any questions regarding the service or repair of this machine, call or write to:

Ridge Tool Company

Technical Service Department

400 Clark Street

Elyria, Ohio 44035-6001

Tel: (800) 519-3456

E-mail: TechServices@ridgid.com

For name and address of your nearest Independent Authorized Service Center, contact the Ridge Tool Com- pany at (800) 519-3456 or http://www.ridgid.com

Ridge Tool Company

13

Image 15
Contents 6200 Table of Contents 6200 Drain Cleaning Machine Personal Safety General Safety InformationWork Area Safety Electrical SafetyTool Use and Care Specific Safety InformationService Drain Cleaner SafetyDescription, Specifications and Standard Equipment Cables and Flexible Trap Leaders Machine AssemblyInstructions For Installing Handles Instructions For Installing CableInstructions For Installing Loading Wheel Instructions For Installing Lifting HookMachine Inspection Machine Set-Up Setting Kickstand BarProper Operating Position Operating InstructionsSpecial Procedures Main Sewer Or Septic Tank OverrunReverse Operation Drum Assembly Removal & Installation Loading The Machine On VehicleOperating Machine In Reclined Position Pigtail Removal and Installation Installing Extra Drum Additional CableProper Tool Selection AccessoriesInstalling K-3800 Drum Using the K-3800 DrumLubrication Maintenance InstructionsMachine Storage Service and Repair Autofeed AssemblyChart 1 Troubleshooting Wiring Diagram115V/60Hz Dégorgeoir électrique K-6200 Table des matières Sécurité individuelle Consignes générales de sécuritéSécurité du chantier Sécurité électriqueService après-vente Consignes de sécurité particulièresUtilisation et entretien de l’appareil Moteur Description, spécifications et équipements de baseSécurité du dégorgeoir SpécificationsCâbles et guides souples Accessoires de baseAccessoires optionnels Equipements de baseMontage de la roue de chargement Installation du mancheInstallation des câbles Assemblage de la machineInspection de la machine Installation du crochet de levageDéploiement de la béquille Préparation de la machinePosition de travail appropriée Utilisation de la machineFonctionnement du levier d’avancement Procédés spéciauxUtilisation de la marche arrière Chargement de la machine sur véhiculeUtilisation de la machine en position couchée Dépose du tambour Dépose et installation du tambourDépose et installation du raccord flexible Installation du tambourTambour K-3800 optionnel AccessoiresInstallation du tambour K-3800 Sélection des outils appropriésCâbles EntretienSystème d’avancement automatique LubrificationStockage de la machine Service après- vente et répara- tionsTableau 1 Dépannage Probleme Raisons Possibles SolutionSchéma électrique Limpiadora de desagües K-6200 Indice Información general de seguridad Seguridad en la zona de trabajoSeguridad eléctrica Seguridad personal Uso y cuidado de la máquinaServicio Descripción Información específica de seguridadDescripción, especificaciones y equipo estándar Seguridad de la Limpiadora de DesagüesAccesorios opcionales EspecificacionesEquipo estándar Accesorios estándarInstrucciones para instalar la rueda de transporte Montaje de la máquinaInstrucciones para montar el mango del soporte Instrucciones para instalar el cableInstrucciones para instalar el gancho de levantamiento Revisión de la máquinaPreparación de la máquina Figura 8 Postura correcta para trabajar Instrucciones para el funcionamientoFigura 9 Funcionamiento de la palanca de autoali- mentación Funcionamiento de la máquina en posi- ción reclinada Procedimientos especialesInstrucciones para el funcionamiento en reversa Cómo cargar la máquina en un vehículoInstalación del tambor Extracción e instalación del tamborInstalación de cable adicional Extracción del tamborAccesorios Extracción e instalación de la colita de cerdoSelección de barrenas Lubricación Instrucciones para el mantenimientoTambor K-3800 opcional AutoalimentaciónServicio y reparaciones Almacenaje de la máquinaTabla 1 Detección de averías Problema Posibles Causas SolucionDiagrama de cableado Limpiadora de desagües K-6200 Limpiadora de desagües K-6200 Ridge Tool Company