RIDGID K6200 manual Machine Set-Up, Setting Kickstand Bar

Page 9

K-6200 Drain Cleaning Machine

8.Inspect the cutting edges of your tools. If necessary, have them sharpened or replaced prior to using the Drain Cleaning Machine. Dull or damaged cutting tools can lead to binding and cable breakage.

9.Inspect cables and couplings for wear and damage. Cables should be replaced when they become severely worn or corroded. A worn cable can be iden- tified when the outside coils become flat.

WARNING Worn or damaged cables can break caus- ing serious injury.

Machine Set-Up

WARNING

To prevent serious injury, proper set-up of the ma- chine and work area is required. The following procedures should be followed to set-up machine:

1.Check work area for:

Adequate lighting.

Grounded electrical outlet.

Clear path to the electrical outlet that does not contain any sources of heat or oil, sharp edges or moving parts that may damage electrical cord.

Dry place for machine and operator. Do not use the machine while standing in water.

Flammable liquids, vapors or dust that may ignite.

2.Position the Drain Cleaning Machine within 3of sewer inlet.

WARNING If sewer inlet greater than 3from the front of the machine, the cable will have a greater tendency to twist or kink. Use a front guide hose or properly support ex- posed cable.

3.Set the spring loaded kickstand bar by tilting the ma- chine forward to allow the bar to pivot behind the tires (Figure 6). Make sure the machine rests firmly on the bar before continuing. The tires should not contact the ground.

Figure 6 – Setting Kickstand Bar

Figure 7 – Releasing Kickstand Bar

WARNING

To prevent tipping during use, machine should rest firmly on the kickstand.

4.Position the air foot switch pedal for easy operator ac- cessibility. Machine is designed for one person operation. (Figure 8)

5.Make sure FOR/OFF/REV switch is in the OFF po- sition.

6.Select and install the proper tool/cutter to the end of the cable. To connect, slide tool and cable together and turn screwdriver slot in coupler 180 degrees. Coupling is in locked position when hash mark is on opposite side of screwdriver slot as shown (Figure 3).

7.Plug the Drain Cleaning Machine into the electrical outlet, making sure to position the power cord along the clear path selected earlier. If the power cord does not reach the outlet, use an extension cord in good condition.

Ridge Tool Company

7

Image 9
Contents 6200 Table of Contents 6200 Drain Cleaning Machine Work Area Safety General Safety InformationElectrical Safety Personal SafetyService Specific Safety InformationDrain Cleaner Safety Tool Use and CareDescription, Specifications and Standard Equipment Instructions For Installing Handles Machine AssemblyInstructions For Installing Cable Cables and Flexible Trap LeadersInstructions For Installing Loading Wheel Instructions For Installing Lifting HookMachine Inspection Machine Set-Up Setting Kickstand BarProper Operating Position Operating InstructionsSpecial Procedures Main Sewer Or Septic Tank OverrunReverse Operation Drum Assembly Removal & Installation Loading The Machine On VehicleOperating Machine In Reclined Position Pigtail Removal and Installation Installing Extra Drum Additional CableInstalling K-3800 Drum AccessoriesUsing the K-3800 Drum Proper Tool SelectionMachine Storage Service and Repair Maintenance InstructionsAutofeed Assembly LubricationChart 1 Troubleshooting Wiring Diagram115V/60Hz Dégorgeoir électrique K-6200 Table des matières Sécurité du chantier Consignes générales de sécuritéSécurité électrique Sécurité individuelleService après-vente Consignes de sécurité particulièresUtilisation et entretien de l’appareil Sécurité du dégorgeoir Description, spécifications et équipements de baseSpécifications MoteurAccessoires optionnels Accessoires de baseEquipements de base Câbles et guides souplesInstallation des câbles Installation du mancheAssemblage de la machine Montage de la roue de chargementInspection de la machine Installation du crochet de levageDéploiement de la béquille Préparation de la machinePosition de travail appropriée Utilisation de la machineFonctionnement du levier d’avancement Procédés spéciauxUtilisation de la marche arrière Chargement de la machine sur véhiculeUtilisation de la machine en position couchée Dépose et installation du raccord flexible Dépose et installation du tambourInstallation du tambour Dépose du tambourInstallation du tambour K-3800 AccessoiresSélection des outils appropriés Tambour K-3800 optionnelSystème d’avancement automatique EntretienLubrification CâblesStockage de la machine Service après- vente et répara- tionsTableau 1 Dépannage Probleme Raisons Possibles SolutionSchéma électrique Limpiadora de desagües K-6200 Indice Información general de seguridad Seguridad en la zona de trabajoSeguridad eléctrica Seguridad personal Uso y cuidado de la máquinaServicio Descripción, especificaciones y equipo estándar Información específica de seguridadSeguridad de la Limpiadora de Desagües DescripciónEquipo estándar EspecificacionesAccesorios estándar Accesorios opcionalesInstrucciones para montar el mango del soporte Montaje de la máquinaInstrucciones para instalar el cable Instrucciones para instalar la rueda de transporteInstrucciones para instalar el gancho de levantamiento Revisión de la máquinaPreparación de la máquina Figura 8 Postura correcta para trabajar Instrucciones para el funcionamientoFigura 9 Funcionamiento de la palanca de autoali- mentación Instrucciones para el funcionamiento en reversa Procedimientos especialesCómo cargar la máquina en un vehículo Funcionamiento de la máquina en posi- ción reclinadaInstalación de cable adicional Extracción e instalación del tamborExtracción del tambor Instalación del tamborAccesorios Extracción e instalación de la colita de cerdoSelección de barrenas Tambor K-3800 opcional Instrucciones para el mantenimientoAutoalimentación LubricaciónServicio y reparaciones Almacenaje de la máquinaTabla 1 Detección de averías Problema Posibles Causas SolucionDiagrama de cableado Limpiadora de desagües K-6200 Limpiadora de desagües K-6200 Ridge Tool Company