Teledyne 9060Z Number of oxygen probes, Oxygen range, Oxygen accuracy, Thermocouple types, Power

Page 10

Model 9060Z Manual

Caution, risk of danger. See additional information in the manual.

3.1HARDWARE SPECIFICATIONS

3.1.1TRANSMITTER SPECIFICATIONS

 

 

 

2 maximum

 

Number of oxygen probes:

 

 

 

0‐1% to 0‐100%

 

Oxygen range:

 

 

 

±1% of actual measured oxygen value with a repeatability of ±0.5% of

 

Oxygen accuracy:

 

 

 

 

the measured value

 

 

Type K, J, R and S

 

Thermocouple types:

 

 

 

±2°C

 

Temperature accuracy:

 

 

 

0‐20mA or 4‐20mA field selectable

 

Analogue outputs:

 

 

 

 

Active outputs (Do NOT loop power these outputs)

 

 

1000 ohm max

 

Output load:

 

 

 

4

 

Alarm relays:

 

 

 

 

2A/240VAC, 2A/30VDC

 

Alarm relay contacts:

 

(WARNING: Do not use both mains voltage and low voltage connections to adjacent alarm contacts)

 

 

 

100 to 240VAC, ‐6 +10%, 50/60 Hz

 

Mains voltage supply:

 

 

 

Category II (IEC60364‐4‐443)

 

Overvoltage:

 

 

 

5W for controller plus probe power

 

Power:

 

 

 

 

530W max., 25% duty cycle each probe on 240VAC

 

 

 

110W max., 100% duty cycle each probe on 110VAC

 

 

 

2.5A max

 

 

3A, fast blow, 250v, 20x5mm (heater fuses, 2 of)

 

Fuses:

 

 

 

 

1A, slow blow, 250v, microfuse (PCB mtg fuse, 1 of)

 

 

Operating Temperature ‐25°C to 55°C

 

Environmental Rating:

 

 

 

 

Relative Humidity 5% to 95% (non‐condensing)

 

 

2000m maximum

 

Altitude

 

 

 

IP65

 

Degree of Protection:

 

 

 

 

IP54 with internal reference air pump

 

 

260mm (10.2”) wide, 160mm (6.3”) high, 90mm (3.5”) deep

 

Case Size:

 

 

 

 

3 Kg (6.6 lbs.)

 

Weight:

WARNING: All signal level connections onto the transmitter must be treated as safety extra‐low voltage (SELV) as defined in the standard IEC61140. Double insulation must be used when connecting these terminals to systems that might carry high voltage.

3.1.2 STANDARD ‘U’ LENGTHS

9060H

9060UL/UH

250 mm (10”)

500 mm (20”)

350 mm (14”)

750 mm (30”)

500 mm (20”)

1000 mm (40”)

750 mm (30”)

1500 mm (60”)

1000 mm (40”)

 

1500 mm (60”)

2000 mm (80”) Ordering Information

10

Image 10
Contents Teledyne Analytical Instruments Model 9060Z Manual Keypad Forcing a Cold Start Resetting the Calibration Factors PurgeEmail asktai@teledyne.com Important Notice Regarding 9060 Probe Option ‐ FIL‐3 Important Notices 9060Z Transmitter IntroductionSeries 9060H Oxygen Probes & Sensors Model 9060Z Manual Alarm relay contacts Temperature accuracyOutput load Alarm relays PowerConnection Weight Temperature RangeHead Temperature 9060H 9060UL/UH ApplicationHeated probes‐temperature range 0‐900C 1650F Model 9060Z Manual Function Minimum Maximum Range of outputsInstalling a 9060H Oxygen Probe Installation and CommissioningMounting the Transmitter Oxygen Probe Mounting 4B Earth Connection PE Installing the Auxiliary Thermocouple4A Shield Connections Electrical ConnectionsModel 9060Z Manual Model 9060Z Manual Heater Interlock Relays Connecting AN Oxygen Probe CableHeater Supply Interlock Connection for Heated Probes Model 9060Z Manual Connecting the Alarms Connecting the Auxiliary Thermocouple OptionalConnecting the Output Channels Connecting the Automatic Purge and Calibration Check SystemConnecting Reference AIR Connecting the Transmitter to a Modbus NetworkProbe or Sensor Calibration Onnecting PowerCommissioning ‐ RUN Mode For more details see AppendixCalibration GAS Check Filter PurgingDust in the Flue GAS Connecting a Pressure Transducer StratificationDisplay and Keypad Graphical DisplayOxygen Display Units Keypad in RUN modeKey text RUN mode White text Setup mode Black text KeypadKeypad in Setup / Commissioning / Calibration modes Enter key Function up and Function down keysOption up and Option down keys Probe impedance keyChanging Options Setup ModeFunction Summary Table Function name RangeProbe 1 Offset Setup Mode FunctionsLower Line Items Oxygen Display Units Process AlarmsDamping Factor Commissioning Mode Model 9060Z Manual Commissioning Mode Functions Model 9060Z Manual Calibration Freezes Outputs Temperature UnitsFlue Pressure Units and Value Solenoid 1 & 2 OperationAlarm Relay 1, 2 and 3 Function Oxygen Content Calibration Gas 1Maximum Calibration Gas 1 & 2 Positive / Negative Error Common Alarm Relay FunctionReference Air Pump Options Operation of the Alarm Relays when an Alarm is AcceptedSelecting the Correct Fuel Function OptionsAlarm Log Clearing Communications Port OptionsCalibration Mode Menu Function name RangeCalibration Mode Functions Reference VoltagesHeater SSR Fault Correction Alarms Common AlarmsModel 9060Z Manual Selectable Process Alarms Alarm Relay Options Instrument Calibration Calibration SummaryProbe Calibration Cold StartCalibration GAS GAS Calibration Check and PurgeFunction # Function Description Options Software Upgrades Detailed Fault Analysis TroubleshootingFirst Approach Cleaning MaintenanceTransmitter Maintenance Replacement PartsIndex Auxiliary ThermocoupleTroubleshooting Is the N/C atom ratio in the fuel Is the H/C atom ratio in the fuelIs the O/C atom ratio in the fuel Is the S/C atom ratio in the fuelProbe EMF Appendix 2, Probe EMF TablesZirconia Oxygen Sensor Output mV Probe Type 9060H, Sensor Probe EMF @ 720C 1320FZirconia Oxygen Probe Output mV Probe Type 9060UL/UH 26.2 13.120.7 33.8Serial Configuration Modbus ProtocolModel 9060Z Manual Model 9060Z Manual Model 9060Z Manual Model 9060Z Manual Model 9060Z Manual 0x03 0x41 Special Instruction Function0x02 0x04