Skil 3400 manual Getting To Know Your Table Saw

Page 20

Getting To Know Your

Table Saw

1. POWER SWITCH

Has a design feature allowing the tool to be locked in the OFF (“O”) position (See page 38 & 39).

2. TABLE

Provides large working surface to support workpiece.

3. BASE

Supports table saw. For additional stability, holes are provided in base to bolt the saw to a workbench or stand.

4. BLADE ANGLE LOCK

Locks the tilt mechanism after the blade is adjusted to desired position.

5. ELEVATION WHEEL

Elevates or lowers the blade at all angles from 0 to 45 degrees.

6. BLADE TILT SCALE

Shows the degree the blade is tilted.

7. RIP FENCE SCALE

Shows the distance from the blade to rip fence.

8. MITER GAUGE SCALE

Shows the degree the workpiece is being mitered.

9. RIP FENCE STORAGE

Conveniently stores rip fence on two pads on the left side of base when not in use. Simply align hole on fence with locating pin on front pad, and press fence down into it’s storage position as shown.

10. MITER GAUGE STORAGE

Conveniently stores miter gauge on the right side of the base when not in use. Simply insert miter gauge bar into rectangular hole on right side of base, and push the miter gauge fully into it’s storage position as shown.

11. BLADE & WRENCH STORAGE

Conveniently stores two 10” blades, hex wrench, & arbor wrench.

12. CORD WRAP

Allows you to easily wrap up the cord so it’s out of the way when transporting or storing.

13. RIP FENCE

Exclusive Self-Aligning, Quick-Set rip fence can be easily moved or locked in place by simply raising or lowering lock handle.

Holes are provided in the rip fence 13 for attaching a wood facing 17 ( Fig. 3). Wood facing should be used when making cuts using dado blades, or ripping thin materials.

Select a piece of smooth straight wood approx. 3/4" thick and the same size as the rip fence.

Attach it to the fence with two round head No. 10 wood screws 1-5/8" long 18 (Fig. 3).

14

FIG. 1

15 13

2

7

							º
						4	5
					º
					40
					º
					35
					º
					0
					3
					º
				5
			º	2
		0º 15º	20
	º	0º 15º
0º	5

10

12

9

4

1

5

3

6

FIG. 2

11

FIG. 3

1713

18

20.

Image 20

Contents Read Before Using Leer antes de usarGeneral Safety Rules Table Saw Specific Safety Rules Basic Operation and Set UpRip Cutting Double Insulated Tools Extension CordsRecommended Sizes of Extension Cords Volt Alternating Current ToolsTable of Contents Tools Needed For Assembly Glossary of TermsConsignes générales de sécurité Consignes de sécurité spécifiques aux scies de table Évitez LES Endroits À L’ATMOSPHÈRE Contaminée PARDES GAZ Prenez Soin DE VOS Outils ET ENTRETENEZ-LES BienRefente Rebond se produitDouble isolation RallongesIdentiques Loguée par l’Underwriter’s Laboratories, l’ACNOR et l’OSHATable des matières Lexique Outils nécessaires à l’assemblageNormas generales de seguridad Normas de seguridad específicas para Sierras de mesa Antes DE Conectar LA Herramienta a UNA Fuente DEEnergia Caja TOMACORRIENTE, TOMACORRIENTE, ETC QUE EL QUE SE Indica EN LA Placa DEL Fabricante DE LACorte al hilo Unicamente Piezas DE Repuesto Identicas Herramientas con aislamiento dobleCordones de extensión Indice Glosario de términos Herramientas necesarias para el ensamblajeGetting To Know Your Table Saw Familiarisez-vous avec Votre scie de table Familiarización con la Sierra de mesaMiter Gauge Blade GuardTable Insert Familiarisez-vous avec Votre scie de table suite Unpacking Checking Contents Piezas sueltas en la cartón Ouverture de l’emballage et vérification du contenuDesempaquetado y Comprobación del contenido Adjustments Adjusting 90Adjusting Positive Stop AT 90 Degrees Adjusting Positive Stop AT 45 DegreesRéglagesAjustes Réglage de l’inclinaison de la lameControl de inclinación de la hoja Réglage des butées fixes 90 etAdjusting Blade Parallel To Miter Gauge Slots Changing The BladeAjustes Del calibre de ingletesCambio de la hoja Cualquier ajusteAligning Rip Fence Pointer AdjustmentMiter Gauge Adjustment Alignement du guide de refente Réglage de l’indicateurAlineación del tope-guía Para cortar al hilo Ajuste del indicadorAssembly7 Attaching Blade GuardAssemblage EnsamblajeMontage du protège-lame Colocación del protector de la hojaAssembly Miter Gauge AssemblyAttaching Handle To Rip Fence Attaching Rip FenceRefente Montage du guide de refenteEnsamblaje del calibre de ingletes Colocación del tope-guía Para cortar al hiloMounting Table Saw Mounting to PlywoodInstallation de la scie De table Montaje de la sierra de MesaSafety Power Switch Using the Miter Gauge with T BarBasic Table Saw Operation Work HelpersUtilisation de la Scie de table Funcionamiento básico De la sierra de mesaUsing The Miter Gauge Auxiliary FenceGuide de coupe auxiliaire Palo de empujar y bloque de empujarTope-guía auxiliar Utilización del calibre de ingletesCrosscutting Repetitive CuttingCoupe transversale Coupe à répétitionCorte transversal Corte repetitivoUsing the Rip Fence Miter CuttingBevel Crosscutting Compound Miter CuttingCoupe angulaire Coupe transversale biseautéeCoupe angulaire biseautée Utilisation du guide de refenteRipping Bevel RippingCoupe en long Corte al hiloCoupe EN Long Biseautée Corte AL Hilo EN BiselResawing Making a FeatherboardCoupe de dédoublement Fabrication d’une planche à LanguettesReaserrado Cómo hacer una tabla con Canto biseladoDado Cutting Non Thru-SawingRabbeting Coupe partielle Réalisation de feuilluresRainurage Aserrado no pasanteSpecial Cutting Techniques MaintenanceMaintaining Your Table Saw Entretien de la Scie de table Mantenimiento de la Sierra de mesaEntretien MantenimientoRecommended Accessories LubricationAccessoires Recommandés Accesorios RecomendadosLubrification Fer de 6 po pour rainures 80050Trouble Shooting Guide de diagnosticLocalización y Reparación de averías Averia LA Sierra no ArrancaHelpful Assembly Hints Assembly FIGTools Required FIG Before YOU Assemble this Tool StandOutils Nécessaires Avant D’ASSEMBLER CET ÉtabliPièces Pour Montage DE LA Scie À Table Conseils Utiles Pour L’ASSEMBLAGEExtension Installation FIG Before YOU Assemble this Extension to Model 3400 Table SAWInstallation DE L’EXTENSION FIG Outils Nécessaires FIGHerramientas Requeridas FIG Instalacion DE LA Extension FIGFront Rail Adjustment Installation of ScaleInstallation DE LA Règle Graduée Table figAjustement DU Rail Avant Ajuste DEL Riel DelanteroLimited Warranty of Skil Benchtop Tools