Skil 3400 manual Bevel Ripping

Page 46

5.Have blade extend approximately 1/8" above top of workpiece. Additional blade exposure would increase the hazard potential.

6. Do not stand directly in front of the blade in case of a

FIG. 39

 

KICKBACK. Stand to either side of the blade.

 

7.Keep your hands clear of the blade and out of the path of the blade.

8.If the blade stalls or stops while cutting, TURN SWITCH OFF before attempting to free the blade.

9.Do not reach over or behind the blade to pull the workpiece through the cut … to support long or heavy workpieces … to remove small cut-off pieces of material or FOR ANY OTHER REASON.

10.Do not pick up small pieces of cut-off material from the table. REMOVE them by pushing them OFF the table with a long stick. Otherwise they could be thrown back at you by the rear of the blade.

11.Do not remove small pieces of cut-off material that may become TRAPPED inside the blade guard while the saw is RUNNING. THIS COULD ENDANGER YOUR HANDS or cause a KICKBACK. Turn the saw OFF. After the blade has stopped turning, lift the guard and remove the piece.

FIG. 40

12.If workpiece is warped, place the CONCAVE side DOWN. This will prevent it from rocking while it is being ripped.

Ripping

RIPPING is known as cutting a piece of wood with the grain, or lengthwise. This is done using the rip fence. Position the fence to the desired WIDTH OF RIP and lock in place. Before starting to rip, be sure:

A. Rip Fence is parallel to sawblade.

B. Spreader is properly aligned with sawblade.

C. Antikickback pawls are functioning properly.

When ripping LONG BOARDS or LARGE PANELS, always use a work support. A simple one can be made by clamping a piece of plywood to a sawhorse (Fig. 39).

BEVEL RIPPING

When bevel ripping material 6" or narrower, use fence on the right side of the blade ONLY. This will provide more space between the fence and the sawblade for use of a Push Stick. If the fence is mounted to the left, the sawblade guard may interfere with proper use of a Push Stick.

When “WIDTH OF RIP” is 6" and WIDER use your RIGHT hand to feed the workpiece, use LEFT hand ONLY to guide the workpiece

…do not FEED the workpiece with the left hand (Fig. 40).

When “WIDTH OF RIP” is 2" to 6" wide USE THE PUSH STICK to feed the work (Fig. 41).

FIG. 41

0º

5º

10º

15º

20º

25º

º 30

35º

40º

45º

46.

Page 45 Page 47
Image 46
Page 45 Page 47
Contents Read Before Using Leer antes de usarGeneral Safety Rules Table Saw Specific Safety Rules Basic Operation and Set UpRip Cutting Recommended Sizes of Extension Cords Double Insulated ToolsExtension Cords Volt Alternating Current ToolsTable of Contents Tools Needed For Assembly Glossary of TermsConsignes générales de sécurité DES GAZ Consignes de sécurité spécifiques aux scies de tableÉvitez LES Endroits À L’ATMOSPHÈRE Contaminée PAR Prenez Soin DE VOS Outils ET ENTRETENEZ-LES BienRefente Rebond se produitIdentiques Double isolationRallonges Loguée par l’Underwriter’s Laboratories, l’ACNOR et l’OSHATable des matières Lexique Outils nécessaires à l’assemblageNormas generales de seguridad Energia Caja TOMACORRIENTE, TOMACORRIENTE, ETC Normas de seguridad específicas para Sierras de mesaAntes DE Conectar LA Herramienta a UNA Fuente DE QUE EL QUE SE Indica EN LA Placa DEL Fabricante DE LACorte al hilo Cordones de extensión Herramientas con aislamiento dobleUnicamente Piezas DE Repuesto Identicas Indice Glosario de términos Herramientas necesarias para el ensamblajeGetting To Know Your Table Saw Familiarisez-vous avec Votre scie de table Familiarización con la Sierra de mesaTable Insert Blade GuardMiter Gauge Familiarisez-vous avec Votre scie de table suite Unpacking Checking Contents Desempaquetado y Comprobación del contenido Ouverture de l’emballage et vérification du contenuPiezas sueltas en la cartón Adjusting Positive Stop AT 90 Degrees AdjustmentsAdjusting 90 Adjusting Positive Stop AT 45 DegreesControl de inclinación de la hoja RéglagesAjustesRéglage de l’inclinaison de la lame Réglage des butées fixes 90 etAdjusting Blade Parallel To Miter Gauge Slots Changing The BladeCambio de la hoja AjustesDel calibre de ingletes Cualquier ajusteMiter Gauge Adjustment Pointer AdjustmentAligning Rip Fence Alineación del tope-guía Para cortar al hilo Alignement du guide de refenteRéglage de l’indicateur Ajuste del indicadorAssembly7 Attaching Blade GuardMontage du protège-lame AssemblageEnsamblaje Colocación del protector de la hojaAttaching Handle To Rip Fence AssemblyMiter Gauge Assembly Attaching Rip FenceEnsamblaje del calibre de ingletes RefenteMontage du guide de refente Colocación del tope-guía Para cortar al hiloMounting Table Saw Mounting to PlywoodInstallation de la scie De table Montaje de la sierra de MesaBasic Table Saw Operation Safety Power SwitchUsing the Miter Gauge with T Bar Work HelpersUtilisation de la Scie de table Funcionamiento básico De la sierra de mesaUsing The Miter Gauge Auxiliary FenceTope-guía auxiliar Guide de coupe auxiliairePalo de empujar y bloque de empujar Utilización del calibre de ingletesCrosscutting Repetitive CuttingCorte transversal Coupe transversaleCoupe à répétition Corte repetitivoBevel Crosscutting Using the Rip FenceMiter Cutting Compound Miter CuttingCoupe angulaire biseautée Coupe angulaireCoupe transversale biseautée Utilisation du guide de refenteRipping Bevel RippingCoupe EN Long Biseautée Coupe en longCorte al hilo Corte AL Hilo EN BiselResawing Making a FeatherboardReaserrado Coupe de dédoublementFabrication d’une planche à Languettes Cómo hacer una tabla con Canto biseladoRabbeting Non Thru-SawingDado Cutting Rainurage Coupe partielleRéalisation de feuillures Aserrado no pasanteMaintaining Your Table Saw MaintenanceSpecial Cutting Techniques Entretien Entretien de la Scie de tableMantenimiento de la Sierra de mesa MantenimientoRecommended Accessories LubricationLubrification Accessoires RecommandésAccesorios Recomendados Fer de 6 po pour rainures 80050Trouble Shooting Guide de diagnosticLocalización y Reparación de averías Averia LA Sierra no ArrancaTools Required FIG Helpful Assembly HintsAssembly FIG Before YOU Assemble this Tool StandPièces Pour Montage DE LA Scie À Table Outils NécessairesAvant D’ASSEMBLER CET Établi Conseils Utiles Pour L’ASSEMBLAGEExtension Installation FIG Before YOU Assemble this Extension to Model 3400 Table SAWHerramientas Requeridas FIG Installation DE L’EXTENSION FIGOutils Nécessaires FIG Instalacion DE LA Extension FIGFront Rail Adjustment Installation of ScaleAjustement DU Rail Avant Installation DE LA Règle GraduéeTable fig Ajuste DEL Riel DelanteroLimited Warranty of Skil Benchtop Tools
Top Page Image Contents