Ryobi WS730 manuel dutilisation Brush Replacement, Proceed as follows when replacement is required

Page 16

MAINTENANCE

Brush REPLACEMENT

See Figure 29, page 23.

The saw has externally accessible brush assemblies that should be periodically checked for wear.

Proceed as follows when replacement is required:

Unplug the saw.

WARNING:

Failure to unplug the saw could result in accidental start- ing causing serious injury.

Remove brush cap with a screwdriver. Brush assembly is spring loaded and will pop out when you remove brush cap.

Remove brush assembly.

Check for wear. Replace both brushes when either has less than 1/4 in. length of carbon remaining. Do not replace one side without replacing the other.

Reassemble using new brush assemblies. Make sure curvature of brush matches curvature of motor and that brush moves freely in brush tube.

Make sure brush cap is oriented correctly (straight) and replace.

Tighten brush cap securely. Do not overtighten.

accessories

The following recommended accessories are currently available at retail stores:

080009002119 Water Pump

A18WS07 Stand

WARNING:

Current attachments and accessories available for use with this tool are listed above. Do not use any attachments or ­accessories not recommended by the manufacturer of this tool. The use of attachments or accessories not recommended can result in serious personal injury.

NOTE: Figures (illustrations) start on page 17 after

French and Spanish language sections.

16 — English

Image 16
Contents OPERATOR’S Manual Save this Manual for Future ReferenceTable of Contents IntroductionGeneral Safety Rules Read ALL Instructions Keep Hands Away from Cutting AREA. Keep  Never Start a Tool When ANY ROTATiNG COMPonent is in Contact with the Workpiece Specific Safety Rules Symbols Symbol Name DESIGNATION/EXPLANATIONService Symbol Signal MeaningSpeed and Wiring ElectricalExtension Cords Electrical ConnectionFeatures Product SpecificationsPosition of the Tile saw Know Your tILE sawAssembly UnpackingInstalling clear hose to water connection­ Installing Tile Cutting WheelInstalling the rip guide Installing the bevel blockConnecting the drainage hose On/off SwitchUsing the rip guide OperationUsing the Water supply valve Using the Flow Adjustment ValveTo make a cross cut To make a diagonal cutTo make a bevel cut Adjustments MaintenanceGeneral Maintenance LubricationBrush Replacement Proceed as follows when replacement is requiredGarantie Páge arrièreAVERTISSEMENT  Règles DE Sécurité GénéralesLire Toutes LES Instructions Règles DE Sécurité Générales Règles DE Sécurité Particulières Symboles NOM Désignation / ExplicationSymbole Signal Signification DépannageCaractéristiques Électriques Instructions de mise à la terreCalibre de fil Du cordon Voir la ,Caractéristiques Placer de la scie à carreauxFiche technique Pour SE Familiariser Avec LA Scie À carreauxInstallation ensemble du moteur de tête pour bÁti Installation rappel de fin de coupeInstallation protection éclabousser­ AssemblageInstallation scie à carreaux dans ­plateau d’eau Installation flexible transparent dans arroser la connexionInstallation meule à carreaux Installation guide de bordUtilisation Connexion du tuyau d’arrosage au scie à carreauxConnexion tuyau de vidanger Commutateur Marche / ArrêtAvertissement  ’utilisation guide de bord’utilisation arroser la soupape de provision ’utilisation Couler LA Soupape D’AJUSTEMENTPour effectuer une coupe en L Pour effectuer une coupe d’ongletPour effectuer une coupe biseau Réglages EntretienEntretien Général LubrificationAccessoires Remplacement des balaisÍndice DE Contenido IntroducciónGarantía Pág. posteriorAdvertencia Reglas DE Seguridad GeneralesLEA Todas LAS Instrucciones Reglas DE Seguridad Generales Reglas DE Seguridad Específicas Símbolos Símbolo Nombre Denominación / ExplicaciónPeligro ServicioPartes Eléctricas Cables de extensiónConexión eléctrica Velocidad Y CableadoCaracterísticas Posicionar del sierra de losasEspecificaciones del producto Familiarícese CON LA Sierra DE losasArmado DesempaquetadoInstalar conjunto del motor de cabeza para armazón Instalar Aviso de extremo de corteS t a l a r p r o t e c t o r p a r a salpicaduras­ Instalar Scie a Carreaux para bandejas de aguaInstalar muela para cortar losas Instalar manguera de transparente para conexión de aguaFuncionamiento ConexiÓn de la manguera de jardÍn a sierra de losasConectar manguera de desagüe Aplicaciones­FLUJO Para efectuar cortes en L Para efectuar cortes a ingletePara efectuar cortes en bisel Ajustes MantenimientoMantenimiento General LubricaciónAccesorios Reemplazo de las escobillasVea la figura 29, página Proceda como sigue cuando se requiera un reemplazoOutils nécessaires Herramientas necesariasEasy Glide Table Easy Glide Table, Easy Glide Table Loose parts Piezas sueltasPage Page Cross cut Coupe transversaleCortes transversales Corte diagonaleBevel cut Cut Coupe d’ongletCorte en bisel Page Page WS730