English
(3)Regarding recharging time
Depending on the combination of the charger and batteries, the charging time will become as shown in Table 3.
Table 3 Charging time (At 20°C)
Charger
Battery | UC14YFA | ||
|
|
| |
EB14B | Approx. | 50 | min. |
EB1430H | Approx. | 70 | min. |
NOTE:
The charging time may vary according to temperature and power source voltage.
4.Disconnect the charger’s power cord from the receptacle.
5.Hold the charger firmly and pull out the battery.
NOTE:
After charging, pull out batteries from the charger first, and then keep the batteries properly.
Regarding electric discharge in case of new batteries, etc.
As the internal chemical substance of new batteries and batteries that have not been used for an extended period is not activated, the electric discharge might be low when using them the first and second time. This is a temporary phenomenon, and normal time required for recharging will be restored by recharging the batteries 2 – 3 times.
How to make the batteries perform longer
(1)Recharge the batteries before they become completely exhausted.
When you feel that the power of the tool becomes weaker, stop using the tool and recharge its battery. If you continue to use the tool and exhaust the electric current, the battery may be damaged and its life will become shorter.
(2)Avoid recharging at high temperatures.
A rechargeable battery will be hot immediately after use. If such a battery is recharged immediately after
use, its internal chemical substance will deteriorate, and the battery life will be shortened. Leave the battery and recharge it after it has cooled for a while.
CAUTION:
◯If the battery has been heated right after operation (or due to sunlight, etc.), the charger’s pilot lamp may not light in red. In such a case, first let the battery cool, then start charging.
◯When the pilot lamp flikers in red quickly (at 0.2- second intervals), check for and take out any foreign objects in the charger’s battery installation hole. If there are no foreign objects, it is probable that the battery or charger is malfunctioning. Take it to your Authorized Service Center.
◯Since the
PRIOR TO OPERATION
1.Preparing and checking the work environment Make sure that the work site meets all the conditions laid forth in the precautions.
2.Checking the battery
Make sure that the battery is installed firmly. If it is at all loose it could come off and cause an accident.
3.Installing the bit
Always follow the following procedure to install driver bit. (Fig. 4)
(1)Pull the guide sleeve back.
(2)Insert the bit into the hexagonal hole in the anvil.
(3)Release the guide sleeve and it returns to its original
position.
CAUTION:
If the guide sleeve does not return to its original position, then the bit is not installed properly.
HOW TO USE
1.Using the convenient hook
The convenient hook can be installed on the right or left side and the angle can be adjusted in 5 steps
between 0° and 80°.
(1)Operating the hook
(a)Pull out the hook toward you in the direction of arrow (A) and turn in the direction of arrow (B). (Fig. 5)
(b)The angle can be adjusted in 5 steps (0°, 20°, 40°, 60°, 80°).
Adjust the angle of the hook to the desired position for use.
(2)Switching the hook position
CAUTION:
Incomplete installation of the hook may result in bodily injury when used.
(a)Securely hold the main unit and remove the screw using a slotted head screwdriver or a coin. (Fig. 6)
(b)Remove the hook and spring. (Fig. 7)
(c)Install the hook and spring on the other side and securely fasten with screw. (Fig. 8)
NOTE:
Pay attention to the spring orientation. Install the spring with larger diameter away from you. (Fig. 8)
(3)Using as an auxiliary light
(a)Press the switch to turn off the light.
If forgotten, the light will turn off automatically after 15 minutes.
(b)The direction of the light can be adjusted within the range of hook positions 1 - 5. (Fig. 9)
◯Lighting time
AAAA manganese batteries: approx. 15 hrs.
AAAA alkali batteries: approx. 30 hrs.
CAUTION:
Do not look directly into the light.
Such actions could result in eye injury.
(4)Replacing the batteries
(a)Loosen the hook screw with a
Remove the hook cover by pushing in the direction of the arrow. (Fig. 11)
(b)Remove the old batteries and insert the new batteries. Align with the hook indications and position the plus (+) and minus
8