Bosch Power Tools PR20EVSK, PR20EVSNK PR007 SIDE-HANDLE Subbase Available as optional accessory

Page 19

BM 2609140437 05-06 5/23/06 3:15 PM Page 19

3.The overlapping piece of laminate should overlap the guiding piece by about 1/2". (The overlapping sheet of laminate will then pass over the aluminum plate and be cut at the proper point by the router bit.)

4.Keep steady pressure on the tool so that the guiding edge of the base remains in contact with the fixed piece of laminate throughout the operation. This is especially important at the beginning and end of a cut.

5.It is also necessary to keep the laminate pressed down tightly near the seam to keep these chips from getting under the laminate. This is especially important on larger pieces of material. The optional PR007 Side Handle Subbase includes a dust extraction hood port that connects to a vacuum hose and helps to keep chips from getting under the laminate.

PR007 SIDE-HANDLE SUBBASE (Available as optional accessory)

See PR007 instruction sheet for complete information about this accessory.

The PR007 Side-Handle Subbase and Dust Extraction Kit (Fig. 35) is a versatile accessory that provides several useful features:

•Additional means of supporting the router

•Dust extraction and collection capability

PR007 Attachment to Palm Router

1.Remove regular subbase

2.Attach side handle subbase with the panhead screws that are included with it.

Additional Means of Supporting

the Router

The knob handle on the PR007 subbase provides an additional gripping point for the palm router / side-handle subbase assembly. It is designed for use when the palm routers are being used in applications that are wide enough that the knob sits over the workpiece. Holding the knob and keeping it pressed down over the workpiece helps keep the routers’ angle to the workpiece unchanged, and is especially helpful when routing edges.

Attachment of PR006 Underscribe

Attachment

The PR006 Underscribe Attachment can also be used with the palm router and the side- handle subbase.

Note: When the underscribe attachment is used with the side-handle subbase, the longer set of attachment screws should be used.

Please refer to PR006 Underscribe Attachment section for further instructions.

Dust Extraction & Collection Capability If you have a shop vacuum system, you can connect it to the PR007’s dust extraction

FIG. 35

attachment to remove routing dust and debris for enhanced utility, visibility and accuracy.

The dust collection capability of the PR007 can be used in both common types of router applications:

1.Routing on flat surfaces

2.Edge-forming

!WARNING To reduce the risk of injury, do not reach in area

of the bit while the router is ON or plugged in. To avoid entangling hoses, do not use this dust extraction hood at the same time as any other dust extraction hood.

Dust Extraction when Routing on

Flat Surfaces

Attach the dust port on the back end of the subbase.

1.Position the port on the backside of subbase

2.Affix using two thumbscrews included.

Dust Extraction when Edge-forming

Attach the dust hood and port on the back end of the subbase.

1.Position the hood on the backside of subbase

2.Position the port on the backside of the dust hood.

3.Affix using two thumbscrews included.

-19-

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Read Before Using Personal safety General Safety RulesWork area safety Electrical safetyPower tools are dangerous in the hands of untrained users Safety Rules for RoutersPower tool use and care ServiceBM 2609140437 05-06 5/23/06 315 PM Symbols Palm Router Functional Description and SpecificationsPR10E PR20EVS Selecting Bits AssemblyRemoving Motor from Base Collet Chuck CareCollet Nut Chuck Check Subbase Location Installing the Motor Into BaseTo Clamp Motor Setting the Depth of CUTFine Depth Adjustment Operating InstructionsElectronic Variable Speed Control Rocker ON/OFF SwitchSoft Start Feature Dial Setting RPM ApplicationWorkpiece Direction of router feed Rate of FeedGuiding the Router PR002 Straight Router GuidePR003 ROLLER/BUSHING Guide Using SELF-PILOTED BitsAnti Rotation Stops PR009 Attachment of Templet Guide Round Subbase FigPR010 Attachment Round Subbase Threaded Templet Guide Fig Panhead ScrewsPR004 Offset Base Motor InstallationHeat Build-Up For more than 10 minutes continuously Offset Base Roller/Bushing Guide Installation of BitUsing the Offset Router Adjustment of Roller/Bushing GuidePR005 Tilt Base Front-to-Back Adjustment Installation FigBit Installation Bit Height AdjustmentAdditional Means of Supporting Router PR007 SIDE-HANDLE Subbase Available as optional accessoryDust Extraction when Edge-forming PR007 Attachment to Palm RouterCarbon Brushes MaintenancePR008 Base Cover Tool LubricationCleaning AccessoriesSécurité personnelle Consignes générales de sécuritéSécurité du lieu de travail Sécurité électriqueEn saillie peut faire sauter loutil Règles de sécurité concernant les toupiesUtilisation et entretien des outils Électroportatifs EntretienAvertissement Le plomb provenant des peintures à base de plombSymboles Toupies à préhension par paume Description fonctionnelle et spécificationsPR10E Pour Enlever UN FER DE Toupie AssemblageChoix DES Fers Montage DES FersEntretien DE LA Douille Montage DU Moteur Dans L’EMBASE Vérification DE Lemplacement DE LA SOUS-EMBASEInférieur à celui de louverture pour le fer et le tranchant Fixation DU Moteur Consignes de fonctionnementRéglage DE LA Profondeur DE Coupe 25 mm environ 3/64 poCircuit Constant Response Fonction DE Démarrage EN DouceurVariateur Électronique DE Vitesse Position Cadran TR/MIN ApplicationCorrecte Il se peut que la toupie cale si elle est utiliséeAssurez-vous toujours que la douille est serrée Coupe librement et le moteur ne ralentit pas, ceciRéglage horizontal Usage DE Fers AutoguidésGuide DE PALIER/BAGUE PR003 Réglage verticalCréation de gabarits Ronde PR009 FigRetirez la sous-embase standard Ronde PR010 FigAccumulation de chaleur Disponible comme accessoire en optionInstallation du moteur Embase Excentrée PR004Utilisation de la toupie excentrée Installation du ferEmbase Inclinable PR005 Création d’un joint Réglage de la hauteur du fer’outil est maintenant prêt pour faire une coupe d’essai Ajustage d’avant en l’arrièrePréhension par la paume Support supplémentaire de la toupieExtraction de la poussière pendant la Formation de bords Paliers EntretienLubrification DE L’OUTIL Balais OU CharbonsEt certains AccessoiresNettoyage Certains AgentsSeguridad personal Normas generales de seguridadSeguridad del área de trabajo Seguridad eléctricaMecánicas Normas de seguridad para fresadorasServicio de ajustes y reparaciones BM 2609140437 05-06 5/23/06 315 PM Con aislamiento doble SímbolosDe Ni-Cd Descripción funcional y especificaciones Que la abertura para la broca y el cortador EnsamblajeSelección DE Brocas Para EvitarRemoción DEL Motor DE LA Base Compruebe LA Ubicación DE LA Subbase Instalación DEL Motor EN LA BasePara Fijar EL Motor Instrucciones de funcionamientoAjuste DE LA Profundidad DE Corte Ajuste DE Profundidad FinoAvance DE LA Fresadora Interruptor Oscilante DE Encendido Y ApagadoDispositivo DE Arranque Suave Circuitería Constant ResponseGuiado DE LA Fresadora Velocidad DE AvanceGuía DE Fresadora Recta Ajuste horizontal Guía DE RODILLO/CASQUILLO PR003Instalación de la guía de rodillo/casquillo Ajuste verticalCreación de plantillas PR009 FigQuite la subbase normal Plantilla roscada PR010 Fig13,000-25,000 RPM cuando se usa con el motor PR20EVE Base Excéntrica PR004Accesorio opcional Acumulación de calorUtilización de la PR004 con la guía de Rodillo/casquillo Instalación de la brocaUtilización de la fresadora excéntrica Ajuste de la guía de rodillo/casquilloAjuste de profundidad Base Inclinable PR005Ajuste del ángulo Para ajustar el ángulo FigAjuste de la altura de la broca Instalación FigAjuste de delante hacia atrás Instalación del aditamento para marcar Por debajo PR006 Creación de una uniónCapacidad de extracción y recolección de polvo Servicio MantenimientoLimpieza AccesoriosRemarques Notas Remarques Notas Limited Warranty of Bosch Portable and Benchtop Power Tools
Related manuals
Manual 84 pages 32.15 Kb
Top Page Image Contents