Panasonic EY3552 IV. Operation, Inserting Battery Pack, Before Using Metal Cutter

Page 10

Inserting Battery Pack

CAUTION:

Before inserting battery pack, check that the power switch in the Metal Cutter actuates properly and returns to the “OFF” position when released.

1.To insert the battery pack: (See Fig.2)

Slide the battery pack in place at the rear of the metal cutter. The battery should snap into place. If the battery is loose, it has not been properly connected.

Fig.2

2.To remove the battery pack:

Press the two tabs on the sides of the battery pack. Slide the battery pack out of the metal cutter body.

IV. OPERATION

Before Using Metal Cutter

This tool is intended for cutting unhardened fer- rous metal and nonferrous metal. Refer to the “Accessories” section for a list of blades to be used for the proper applications of this tool. The following precautions must be followed to reduce the risk of injury;

•Do not cut stacked materials. Cut one piece at a time.

•Do not cut hardened steel.

•Cut materials with the wider edge of the shoe over the clamped side of the material.

•Do not touch the saw blade, workpiece, or cutting chips with bare hands immediately after cutting; they may be hot and could burn skin.

Each time you use the metal cutter, you must make sure it is in good operating condition.

Use the following checklist:

1.Is the blade installed in the correct direction? The arrow on the blade must point in the same direction as the arrow on the upper blade cover.

2.Is the blade installed properly?

Make sure the hex bolt is tightened securely. (See Fig.12)

3.Does the blade look alright?

Replace the blade immediately if there are any cracks in it or if any teeth are broken.

4.Does the lower guard close properly?

WARNING

To avoid injury, do not use the metal cutter if the lower guard does not close quickly over the blade.

5.Is the transparent guard securely installed?

6.Is the battery pack charged and inserted firmly to the metal cutter?

7.Is the depth adjustment lever for cutting securely tightened?

8.Is the workpiece securely clamped on a saw horse or bench?

Using Metal Cutter

CAUTION:

To reduce the risk of injury read the Safety Instructions at the front of this manual before using the metal cutter.

WARNING

To reduce the risk of injury, wear safety goggles or glasses with side shields.

Follow these steps:

Hold the metal cutter with both hands. (See Fig.4) Do not attempt to remove cut material when blade is moving.

1.Line up the sight line on shoe with your cutting line. (See Fig.3)

Alignment with cutting line

•Use the notch as guide to establish cutting position. Align the notch with cutting line.

As the cutting position may differ depending on the blade, do a trial cut beforehand.

Cutting line

Notch

Guide line of blade front

Fig.3

- 10 -

Image 10
Contents Model No EY3552 ImportanteBattery charger EY0110 Chargeur de batterie EY0110 Depth adjustment leverFront grip Bouton avant Asidera delantera Switch lock lever Lower guard Protège-lame inférieurGeneral Safety Rules II. Safety Instruc TionsIntroduction Battery tool use and care Personal safetyPower tool use and care ServiceFurther Safety Instruc- tions for All Saws Safety Instructions for All SawsCauses and operator prevention of kickback Blade binding and kickback Safety Instructions for This SawSymbol Protruding blade may cut objects that can cause kickbackAmperes AWG Size of Cord Equal to or But less For Battery Charger & Battery PackImportant Safety Instructions Greater than Than 100Do not change the plug in any way Charging Battery Pack EY9251 III. Setting UPLamp Indications Using Metal Cutter Inserting Battery PackBefore Using Metal Cutter IV. OperationRip fence EY3500B7727 Cutting depth adjustmentRip Fence Cutting large sheets For Proper Use Further DetailCutting thin or corrugated materials Right WrongMaintenance Removing BladeBattery Pack Life Installing BladeFor Appropriate use of Battery pack Battery RecyclingVI.ACCESSORIES EY9PM17BVII.SPECIFICATIONS Sécurité de la zone de travail II. Instructions DE SÉ CuritéConsignes de sécurité générales Sécurité électriqueSécurité personnelle Maintenez les outils de coupe affûtés et propresCeci assure le maintien de la sécurité de loutil mécanique RéparationCauses et prévention par lutilisateur dun retour Nutilisez pas de lames émoussées ou endom- magées Chargeur de batterie et batterie autonome SymboleInstructions de sécurité impor- tantes Ampères III. Préparatifs D’UTI LisationCharge de la batterie autonome EY9251 Egal ou supé Mais inféMise EN Garde Indication du voyantComment emboîter la batterie autonomeVoir la fig Utilisation de la scie circulaire à couper les métaux Alignement sur la ligne de sciageRetirez la batterie autonome Ajustement de la profondeur de sciageGuide de sciage EY3500B7727 SerrerSupplémentaires Pour éviter de se blesser gravementIncorrect Correct’assurer que la lame de scie s’arrête complètement Mobile inférieur EntretienComment retirer la lame de scie Découpée face à vousRecyclage de la batterie auto- nome Pour utiliser correctement la batterie autonomeLongévité des batteries Nettoyage de la scie circulaire à couper les métauxLame pour matériaux métalliques EY9PM17A VI. AccessoriesProtège-lame transparent Batterie autonome EY9251 Chargeur de batterie EY0110VII.FICHE Technique II. Instrucciones DE Seguridad IntroducciónReglas de seguridad ge- nerales Uso y cuidado de la herramien- ta a batería Seguridad personalUso y cuidados de herramientas eléctricas AplicaciónEsto mantendrá la seguridad de la herramien- ta eléctrica Instrucciones de segu- ridad para todas las sie- rrasServicio Causas y prevención de retroceso del operadorInstrucciones de segu- ridad para esta sierra Pieza, en todos los ángulos y profundidades del corteInstrucciones de seguridad im- portantes Para el cargador de ba- teria y la bateriaSímbolo No exponga el cargador y la batería a la lluvia o nieveVicio calificado III. PreparativosCarga de la batería EY9251 Mientas de uso especialPrecaución Indicación de la lámparaInserción de la batería Ahora cargando La carga ha sido completadaPalanca de bloqueo del interruptor Mango Empuñadura Utilización de la sierra para me- talesAlineación con la línea de corte Delantera AlimentaciónGuía de corte EY3500B7727 Ajuste de la profundidad del corteProfundidad Utilización adecuada detalles adicionales Corte de hojas grandesBueno Cerciórese de que la cuchilla esté paradaMantenimiento Desmontaje de la cuchillaVida útil de la batería Instalación de la cuchillaPara un uso adecuado de la ba- tería Reciclado de la bateriaVI. Accesorios VII.ESPECIFICACIONES Panasonic Consumer Electronics Company