Genie 1042 manual Power Head & Rail Assembly, Use 16-18 x 1/2 Bolts

Page 11

POWER HEAD & RAIL ASSEMBLY

Assembly for CHAIN DRIVE OPENER

NOTE: Handle carefully! Drive chain can slide out of rail.

NOTE: For power head and rail assembly locate Bag 1 from Box 1.

1.Attach rail assembly to power head by aligning the sprocket onto the motor shaft. Use (3) bolts, 5/16"-18 x 1/2" (Fig. 1-5).

2.Tighten the chain by turning the adjustment nut clockwise. The chain adjustment nut is located in the Chain Pulley Bracket (opposite rail end from the power head) (Fig. 1-6).

3.Tighten chain until chain is approximately 1/8 inch above the base of the rail at midpoint on the rail (Fig. 1-6). Do NOT over tighten chain.

CAUTION

You should have removed all ropes and/or cables (NOT door lift cables) and disabled the door lock already. If you have not, remove all ropes and/or cables and disable garage door lock NOW before continuing with installation (Fig. 1-8).

Set assembled power head and rail aside. Begin with Section 2 INSTALLATION.

Use

5/16"-18 x 1/2" Bolts

FIG. 1-5 Rail - Power head assembly.

 

Chain Pulley Bracket (at wall end of rail)

 

 

Use 1/2" socket

 

 

on adjustment nut

 

 

Tighten nut to move pulley this direction

 

 

Chain

 

 

Chain

 

 

1/8"

 

 

T-Rail at center of rail assembly

T-Rail

 

 

FIG. 1-6

Chain adjustment.

 

Assembly for BELT DRIVE OPENER

NOTE: For power head and rail assembly locate Bag 1 from Box 1.

1.Attach rail assembly to power head by aligning the sprocket onto the motor shaft. Use (3) bolts, 5/16"-18 x 1/2" (Fig. 1-5).

2.Tighten the belt by turning the adjustment nut clockwise. The belt adjustment nut is located in the Belt Pulley Bracket (opposite rail end from the power head) (Fig. 1-7).

3.Tighten belt until belt is approximately 1/8 inch above the base of the rail at midpoint on the rail (Fig. 1-7). Do NOT over tighten belt.

CAUTION

You should have removed all ropes and/or cables (NOT door lift cables) and disabled the door lock already. If you have not, remove all ropes and/or cables and disable garage door lock NOW before continuing with installation (Fig. 1-8).

Set assembled power head and rail aside. Begin with Section 2 INSTALLATION.

 

Belt Pulley Bracket (at wall end of rail)

 

 

Use 1/2" socket

 

 

on adjustment nut

 

 

Tighten nut to move pulley this direction

 

 

Belt

 

 

Belt

 

 

1/8"

 

 

T-Rail at center of rail assembly

T-Rail

 

 

FIG. 1-7

Belt adjustment.

 

Remove

Remove

FIG. 1-8 Disable garage door lock.

PN# 36420Supplement, 10/27/2008

11

 

Page 10 Page 12
Image 11
Page 10 Page 12
Contents CHAINLIFT/BELTLIFT Models 1022/1024/1042 Do not allow children to play with the door operator Turn OFF power before removing operator coverSystem technician using proper tools and instructions Keep people clear of opening while door is movingSafety Features Table of ContentsOpener Features Do not USE AN Extension Cord Pg Pg Typical Sectional Door InstallationParts Identification Not Shown Full Size Recommended ToolsDo not Return to Point of Purchase Piece Rail Hardware Assembled View ChainOpener Assembly Important Installation InstructionsChain Use 16-18 x 1/2 Bolts Power Head & Rail AssemblyDo not move door spring Mounting the header bracket Installation Header and Door Mounting BracketsFinding header bracket mounting location Attach angle iron to beams Mounting the assemblyMounting the Opener Getting startedDoor Bracket Install Door ArmsWall Button location Wall Button Installation2a. Wiring If pre-wired 2b. Wiring If not pre-wiredMounting Securely fasten wiresDo not install rear cover yet Mounting Safe-T-BeamSource Red LED and Sensor Green LED SAFE-T-BEAMSYSTEM Installation3a. Wiring If not pre-wired Do not install the white lamp cover at this time 3b. Wiring pre-wiredRoute Safe-T-Beamwires through wire guide With Grounded Plug Connecting to PowerWith Permanent Wiring With Power SuppliedClose Travel Limit Setting & Testing OPEN/CLOSE LimitsDoor Limits Keyed Emergency Release Operation Instructions Carriage LockKeyed Emergency Release Contact Reverse Test UP/DOWN ForceErase OPEN/CLOSE Travel Limit Lost or Stolen Remote Programming Remote ControlsLight bulb Light BULB/LENS InstallationBattery replacement Visor clipContact reverse MaintenanceRoutine Monthly Maintenance Door balanceAdvertencia Avertissement Circuit Wiring DiagramProblem What to do Troubleshooting Guide OperationPossible Problem Solution Troubleshooting Guide Power Head LEDTransmitter Compliance Statement Page This page left blank Clignote Solution Possible ProblèmeSolución Problema Posible Fonctionnement Dépannage DE Guide Del funcionamiento Mal Funcionamiento DE Problema Averías DE Investigación DE GuíaRutina DE Avertissement MaintenanceAdvertencia MantenimientoAvertissement Pile la Lentille la FixerLente la Apriete Viseur du clip le Fixer Visera de sujetador el AcopleRobado O Perdido Remoto ’IC DE ET FCC LA DE Reglementation LA a ConformeBotón Remotos Controles DE ProgramaciónPuerta la de vano Del centro del debajo 4 x Inverso Contacto DE PruebaCerrar ABRIR/ DE Recorrido DEL Límite Borrar HAUT/BAS ForceCON Pestillo DE Picaporte Avertissement AdvertenciaCLÉ Secours DE DéverrouillageCorredizo al cadena la Engrana AdvertenciaPuerta LA DE Límites ABRIR/CERRARTension Sous InfrarrojaProtección DE Función Precaución Garde EN MisePrecaución Garde EN MiseTapa la de Presillas Arrière couvercle le InstallerPosterior tapa la Instale Couvercle du ClipsBeam-T-Safe del Fuente y detector del Lugares Fuente y detector Del alambrado de MétodosPuerta la de marco el Marque Soportes Los a detectores los AcopleMontaje de Soportes Montage CoinçageMurale MontajePared de control Del alambre de Recorrido Pared DE Control DEL InstalaciónDénudage et Division Pelando y PartiendoPuerta LA DE Soporte ’OUVREUR DE Montage Instalación InstallationControl De caja la de Conjunto Riel Riel DEL10/27/2008 36420Supplement, PN# Cadena la de AjustePORTE-OUVRE pour rail de Ensemble Partido riel del ConjuntoRiel de partidas Secciones Abridor DEL Conjunto ’OUVREURDe risque de d’AVERTISSEMENT l’étiquette Placer La de l’ouvreur installer possible, du mesure la DansPieza 1 DE Riel DEL Herrajes DE Montaje DEL Vista Assemblée Pièce 1 À Rail DU Quincaillerie LA DE VUEMANQUANTES? Pièces Recommandés Outils Recomendadas Herramientas OU / O 12 .Pg / .Pág11 .Pg / .Pág 18-17 .Pg 14 .PgSection à référer Se .librement Section la à reporter se installée fois uneAluminium, léger, acier en plaques des Elle-t-a section a garage de porte Votre4 Secciones las a Refiérase Abridor DEL Características Matières DES TableÍndice Seguridad DE CaracterísticasMouvement Terre la à mis correctement être doit l’ouvreurMobiles pièces Beltliftchainlift

1042 specifications

The Genie 1042 is a versatile and efficient aerial work platform designed to meet the demands of various industries, from construction to maintenance and operations. This compact boom lift is renowned for its remarkable lifting capabilities and user-friendly features, making it a favorite among professionals seeking reliability and performance.

One of the standout features of the Genie 1042 is its impressive working height, reaching up to 40 feet, and a horizontal outreach of 22 feet. This combination of height and reach makes it ideal for tasks that require working at significant elevations while still maintaining a solid base. The platform extends and retracts smoothly, providing operators with the flexibility to navigate around obstacles and access hard-to-reach areas effectively.

Powered by an efficient electric motor, the Genie 1042 operates quietly, making it suitable for indoor use and residential areas where noise restrictions may be a factor. The electric motor also offers zero emissions, aligning with modern environmental standards and preferences for greener equipment. Its compact design, with a width of just 4 feet, allows it to maneuver easily through standard doorways and tight spaces, enhancing its practicality on job sites.

Safety is a priority with the Genie 1042, featuring an intuitive operator control system and standard safety measures, including a tilt sensor and emergency stop buttons. The platform is equipped with guardrails, ensuring operator security while working at height. The sturdy construction of the Genie 1042 also contributes to stability, enabling users to focus on their tasks without worrying about the integrity of the lift.

Additionally, Genie has incorporated advanced technologies into the 1042 model, including a diagnostics system that provides real-time feedback on the machine's performance. This feature enhances maintenance efficiency, allowing operators to monitor the health of the platform and address potential issues proactively.

In summary, the Genie 1042 embodies a combination of height, outreach, and compactness, backed by reliable electric power, advanced safety features, and intelligent technology. Whether used in construction, maintenance, or any other sector requiring elevated work, the Genie 1042 proves to be a formidable tool that enhances productivity while prioritizing operator safety and environmental responsibility.
Top Page Image Contents