Genie 1042 manual Door Limits, Setting & Testing OPEN/CLOSE Limits, Close Travel Limit

Page 20

6DOOR LIMITS

WARNING

•Severe injury or death can result if the door closing force is set too high.

•Never increase the door closing force above the minimum required to move the door.

•Never adjust force to compensate for a sticking or binding door.

•Perform monthly CONTACT REVERSE TEST as described on page 22 and in Section 10.

SETTING & TESTING OPEN/CLOSE LIMITS

The OPEN (UP) and CLOSE (DOWN) door positions are controlled by making the adjustments on the panel located on the bottom of the power head. The adjustments that can be made are:

•Close Travel Limit,

•Open Travel Limit, Maximum Closing Force Maximum Opening Force Transmitter Programming

ENGAGE CHAIN/BELT CONNECTOR TO CARRIAGE

1.Press and hold the "Close Travel Limit" button until the chain or belt connector advances and engages to the Carriage Assembly (FIG 6-2).

CAUTION

Failure to verify the engagement of the belt/chain connector will result in damage to rail components.

CLOSE TRAVEL LIMIT

1.Press and hold the "Close Travel Limit" button until the door is fully closed.

2.You can quickly press and release the "Close Travel Limit" button to move the door in small increments. You can also use the "Open Travel Limit" button to move the door slightly in the UP direction.

3.Door is fully closed when the bottom edge of door presses firmly onto the ground.

4.Once the door is in the desired position, press and release the "Down SET Limit" SET button. The LED indicator light light will blink green once. This stores the closed position in memory.

OPEN TRAVEL LIMIT

1.Press and hold the "Open Travel Limit" button to move the door to its fully opened position. This starts the opener moving in the UP direction.

2.Hold the "Open Travel Limit" button until the door is in the fully opened position that you desire, then release this button.

3.You can quickly press and release the "Open Travel Limit" button to move the door in small increments. You can also use the "Close Travel Limit" button to move the door slightly in the DOWN direction.

4.Once the door is in the desired position, press and release the "Open SET Limit" SET button. The LED indicator light will blink green twice. This stores the opened position in memory.

FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM

Limit Controls location on power head.

LED

Open

Open

 

 

Indicator Light

Set Limit

 

Up Force

Travel Limit

 

 

Button

OPEN

Control

 

 

 

 

 

 

 

 

 

Adjustment

To

 

SET

 

 

Garage Door

 

 

 

 

 

 

 

LEARN MANUAL LIMIT FORCE

 

 

 

 

 

 

SET

 

 

Learn

 

 

 

 

 

 

 

Code

 

CODE

Close

 

Close

CLOSE

Down Force

Button

 

 

Set Limit

 

 

 

 

Travel Limit

 

Control

 

 

 

 

 

 

Button

 

Adjustment

FIG. 6-1

Limit controls.

 

 

 

 

 

Move

 

 

 

 

 

 

 

 

in

this

dir

 

 

Latch

 

 

 

 

 

 

 

 

 

 

 

 

ec

 

Movement

 

 

 

 

 

 

tion

 

 

 

 

 

 

 

 

 

 

Carriage Assembly

Chain Connector

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Latch

 

 

 

 

 

 

 

 

Movement

 

 

M

 

 

 

 

 

 

 

 

ove

 

 

 

 

 

 

 

 

in

 

 

 

 

 

 

 

 

this

dir

 

 

Latch

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ec

 

Movement

 

 

 

 

 

 

tion

 

 

Carriage Assembly

Belt Connector

Latch

Movement

FIG. 6-2 Engage Chain/Belt Connector to Carriage.

CAUTION

Operation of the opener without the Chain or Belt Connector engaged to the Carriage Assembly will result in damage to rail components including the rail pulley.

20

PN# 36420Supplement, 10/27/2008

 

Page 19 Page 21
Image 20
Page 19 Page 21
Contents CHAINLIFT/BELTLIFT Models 1022/1024/1042 Turn OFF power before removing operator cover System technician using proper tools and instructionsKeep people clear of opening while door is moving Do not allow children to play with the door operatorSafety Features Table of ContentsOpener Features Do not USE AN Extension Cord Typical Sectional Door Installation Pg PgRecommended Tools Parts Identification Not Shown Full SizeDo not Return to Point of Purchase Chain Piece Rail Hardware Assembled ViewImportant Installation Instructions Opener AssemblyChain Power Head & Rail Assembly Use 16-18 x 1/2 BoltsDo not move door spring Mounting the header bracket Installation Header and Door Mounting BracketsFinding header bracket mounting location Mounting the assembly Mounting the OpenerGetting started Attach angle iron to beamsInstall Door Arms Door BracketWall Button Installation 2a. Wiring If pre-wired2b. Wiring If not pre-wired Wall Button locationMounting Securely fasten wiresDo not install rear cover yet Mounting Safe-T-BeamSource Red LED and Sensor Green LED SAFE-T-BEAMSYSTEM Installation3a. Wiring If not pre-wired Do not install the white lamp cover at this time 3b. Wiring pre-wiredRoute Safe-T-Beamwires through wire guide Connecting to Power With Permanent WiringWith Power Supplied With Grounded PlugClose Travel Limit Setting & Testing OPEN/CLOSE LimitsDoor Limits Keyed Emergency Release Operation Instructions Carriage LockKeyed Emergency Release Contact Reverse Test UP/DOWN ForceErase OPEN/CLOSE Travel Limit Programming Remote Controls Lost or Stolen RemoteLight BULB/LENS Installation Battery replacementVisor clip Light bulbMaintenance Routine Monthly MaintenanceDoor balance Contact reverseCircuit Wiring Diagram Advertencia AvertissementTroubleshooting Guide Operation Problem What to doTroubleshooting Guide Power Head LED Possible Problem SolutionTransmitter Compliance Statement Page This page left blank Solution Possible Problème ClignoteSolución Problema Posible Fonctionnement Dépannage DE Guide Funcionamiento DE Problema Averías DE Investigación DE Guía Del funcionamiento MalAvertissement Maintenance AdvertenciaMantenimiento Rutina DEAvertissement Lentille la Fixer Lente la AprieteViseur du clip le Fixer Visera de sujetador el Acople Pile la’IC DE ET FCC LA DE Reglementation LA a Conforme Robado O Perdido RemotoRemotos Controles DE Programación BotónInverso Contacto DE Prueba Cerrar ABRIR/ DE Recorrido DEL Límite BorrarHAUT/BAS Force Puerta la de vano Del centro del debajo 4 xAvertissement Advertencia CLÉSecours DE Déverrouillage CON Pestillo DE PicaporteAdvertencia Puerta LA DE LímitesABRIR/CERRAR Corredizo al cadena la EngranaTension Sous InfrarrojaProtección DE Función Garde EN Mise PrecauciónGarde EN Mise PrecauciónArrière couvercle le Installer Posterior tapa la InstaleCouvercle du Clips Tapa la de PresillasFuente y detector Del alambrado de Métodos Beam-T-Safe del Fuente y detector del LugaresPuerta la de marco el Marque Soportes Los a detectores los AcopleMontaje de Soportes Coinçage MuraleMontaje MontagePared DE Control DEL Instalación Dénudage et DivisionPelando y Partiendo Pared de control Del alambre de RecorridoPuerta LA DE Soporte ’OUVREUR DE Montage Installation InstalaciónRiel DEL 10/27/2008 36420Supplement, PN#Cadena la de Ajuste Control De caja la de Conjunto RielPORTE-OUVRE pour rail de Ensemble Partido riel del ConjuntoRiel de partidas Secciones ’OUVREUR Abridor DEL ConjuntoLa de l’ouvreur installer possible, du mesure la Dans De risque de d’AVERTISSEMENT l’étiquette PlacerAssemblée Pièce 1 À Rail DU Quincaillerie LA DE VUE Pieza 1 DE Riel DEL Herrajes DE Montaje DEL VistaMANQUANTES? Pièces Recommandés Outils Recomendadas Herramientas 12 .Pg / .Pág 11 .Pg / .Pág 18-17 .Pg14 .Pg OU / OSection la à reporter se installée fois une Aluminium, léger, acier en plaques desElle-t-a section a garage de porte Votre Section à référer Se .librement4 Secciones las a Refiérase Matières DES Table ÍndiceSeguridad DE Características Abridor DEL CaracterísticasMouvement Terre la à mis correctement être doit l’ouvreurMobiles pièces Beltliftchainlift

1042 specifications

The Genie 1042 is a versatile and efficient aerial work platform designed to meet the demands of various industries, from construction to maintenance and operations. This compact boom lift is renowned for its remarkable lifting capabilities and user-friendly features, making it a favorite among professionals seeking reliability and performance.

One of the standout features of the Genie 1042 is its impressive working height, reaching up to 40 feet, and a horizontal outreach of 22 feet. This combination of height and reach makes it ideal for tasks that require working at significant elevations while still maintaining a solid base. The platform extends and retracts smoothly, providing operators with the flexibility to navigate around obstacles and access hard-to-reach areas effectively.

Powered by an efficient electric motor, the Genie 1042 operates quietly, making it suitable for indoor use and residential areas where noise restrictions may be a factor. The electric motor also offers zero emissions, aligning with modern environmental standards and preferences for greener equipment. Its compact design, with a width of just 4 feet, allows it to maneuver easily through standard doorways and tight spaces, enhancing its practicality on job sites.

Safety is a priority with the Genie 1042, featuring an intuitive operator control system and standard safety measures, including a tilt sensor and emergency stop buttons. The platform is equipped with guardrails, ensuring operator security while working at height. The sturdy construction of the Genie 1042 also contributes to stability, enabling users to focus on their tasks without worrying about the integrity of the lift.

Additionally, Genie has incorporated advanced technologies into the 1042 model, including a diagnostics system that provides real-time feedback on the machine's performance. This feature enhances maintenance efficiency, allowing operators to monitor the health of the platform and address potential issues proactively.

In summary, the Genie 1042 embodies a combination of height, outreach, and compactness, backed by reliable electric power, advanced safety features, and intelligent technology. Whether used in construction, maintenance, or any other sector requiring elevated work, the Genie 1042 proves to be a formidable tool that enhances productivity while prioritizing operator safety and environmental responsibility.
Top Page Image Contents