Genie 1042 Routine Monthly Maintenance, Door balance, Contact reverse, Safe-T-BeamSystem

Page 25

IMPORTANT SAFETY INSTRUCTIONS

WARNING:

Toreduce the risk of severe injury or death:

1.READ AND FOLLOW ALL INSTRUCTIONS.

2.Never let children operate or play with the door controls. Keep the remote control away from children.

3.Always keep the moving door in sight and away from people and objects until the door is completely closed. NO ONE SHOULD CROSS THE PATH OF THE MOVING DOOR.

4.NEVER GO UNDER A STOPPED, PARTIALLY OPEN DOOR.

5.Test opener monthly. The door MUST reverse on contact with a 1-1/2" high object (or a 2" x 4" board laid flat) at the center of the doorway on the floor. After adjusting either the force or the limit of travel, retest the door opener. Failure to adjust the opener properly may cause severe injury or death.

6.When possible, use the emergency release only when the door is closed. Use caution when using this release with the door open. Weak or broken springs are capable of increasing the rate of door closure and increasing the risk of severe injury or death.

7.KEEP DOORS PROPERLY BALANCED. See your garage door Owner’s Manual. An improperly balanced door increases the risk of severe injury or death. Have a trained door system technician make repairs to cables, spring assemblies, and other hardware.

8.SAVE THESE INSTRUCTIONS.

If you have any questions, please do not hesitate to contact Genie® customer service at:

1.800.354.3643

10 MAINTENANCE

WARNING

•Garage door hardware (springs, cables, brackets, pulleys, etc.) are under extreme pressure and tension.

•DO NOT attempt to repair or adjust door springs or any hardware, and DO NOT OPERATE garage door automatically or manually if door is improperly balanced or springs are broken.

–CONTACT A TRAINED DOOR SYSTEM TECHNICIAN.

ROUTINE MONTHLY MAINTENANCE

1.Door balance.

•With the door closed, pull emergency release knob (Carriage Lock) towards the opener to release door from carriage assembly.

•Raise door manually approximately 3'- 4' and release.

–Door should remain stationary or move very slightly.

–If door moves quickly, CONTACT A TRAINED DOOR SYSTEM TECHNICIAN.

•Close the door.

•Pull emergency release knob towards door to engage carriage.

–Operate door using remote.

–Door will re-attach itself to carriage assembly.

2.Contact reverse.

•Place a 2" x 4" board laid flat on floor.

–In center of garage door opening.

•Close door by using wall button or remote control.

–Door fails to reverse on contact with board (See section 7 "CONTACT REVERSE.")

–Opener still fails

CONTACT THE GENIE COMPANY OR AN AUTHORIZED GENIE® DEALER.

3.Safe-T-Beam®System.

• Red LED blinks.

– check alignment (See section 5 ).

WARNING

Use Wall Button supplied with opener. Any other Wall Button can cause the opener to operate unexpectedly.

PN# 36420Supplement, 10/27/2008

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents CHAINLIFT/BELTLIFT Models 1022/1024/1042 System technician using proper tools and instructions Turn OFF power before removing operator coverKeep people clear of opening while door is moving Do not allow children to play with the door operatorOpener Features Table of ContentsSafety Features Do not USE AN Extension Cord Pg Pg Typical Sectional Door InstallationParts Identification Not Shown Full Size Recommended ToolsDo not Return to Point of Purchase Piece Rail Hardware Assembled View ChainOpener Assembly Important Installation InstructionsChain Use 16-18 x 1/2 Bolts Power Head & Rail AssemblyFinding header bracket mounting location Installation Header and Door Mounting BracketsDo not move door spring Mounting the header bracket Mounting the Opener Mounting the assemblyGetting started Attach angle iron to beamsDoor Bracket Install Door Arms2a. Wiring If pre-wired Wall Button Installation2b. Wiring If not pre-wired Wall Button locationDo not install rear cover yet Securely fasten wiresMounting 3a. Wiring If not pre-wired SAFE-T-BEAMSYSTEM InstallationMounting Safe-T-BeamSource Red LED and Sensor Green LED Route Safe-T-Beamwires through wire guide 3b. Wiring pre-wiredDo not install the white lamp cover at this time With Permanent Wiring Connecting to PowerWith Power Supplied With Grounded PlugDoor Limits Setting & Testing OPEN/CLOSE LimitsClose Travel Limit Keyed Emergency Release Carriage LockKeyed Emergency Release Operation Instructions Erase OPEN/CLOSE Travel Limit UP/DOWN ForceContact Reverse Test Lost or Stolen Remote Programming Remote ControlsBattery replacement Light BULB/LENS InstallationVisor clip Light bulbRoutine Monthly Maintenance MaintenanceDoor balance Contact reverseAdvertencia Avertissement Circuit Wiring DiagramProblem What to do Troubleshooting Guide OperationPossible Problem Solution Troubleshooting Guide Power Head LEDTransmitter Compliance Statement Page This page left blank Clignote Solution Possible ProblèmeSolución Problema Posible Fonctionnement Dépannage DE Guide Del funcionamiento Mal Funcionamiento DE Problema Averías DE Investigación DE GuíaAdvertencia Avertissement MaintenanceMantenimiento Rutina DEAvertissement Lente la Apriete Lentille la FixerViseur du clip le Fixer Visera de sujetador el Acople Pile laRobado O Perdido Remoto ’IC DE ET FCC LA DE Reglementation LA a ConformeBotón Remotos Controles DE ProgramaciónCerrar ABRIR/ DE Recorrido DEL Límite Borrar Inverso Contacto DE PruebaHAUT/BAS Force Puerta la de vano Del centro del debajo 4 xCLÉ Avertissement AdvertenciaSecours DE Déverrouillage CON Pestillo DE PicaportePuerta LA DE Límites AdvertenciaABRIR/CERRAR Corredizo al cadena la EngranaProtección DE Función InfrarrojaTension Sous Precaución Garde EN MiseGarde EN Mise PrecauciónPosterior tapa la Instale Arrière couvercle le InstallerCouvercle du Clips Tapa la de PresillasBeam-T-Safe del Fuente y detector del Lugares Fuente y detector Del alambrado de MétodosMontaje de Soportes Soportes Los a detectores los AcoplePuerta la de marco el Marque Murale CoinçageMontaje MontageDénudage et Division Pared DE Control DEL InstalaciónPelando y Partiendo Pared de control Del alambre de RecorridoPuerta LA DE Soporte ’OUVREUR DE Montage Instalación Installation10/27/2008 36420Supplement, PN# Riel DELCadena la de Ajuste Control De caja la de Conjunto RielRiel de partidas Secciones Partido riel del ConjuntoPORTE-OUVRE pour rail de Ensemble Abridor DEL Conjunto ’OUVREURDe risque de d’AVERTISSEMENT l’étiquette Placer La de l’ouvreur installer possible, du mesure la DansPieza 1 DE Riel DEL Herrajes DE Montaje DEL Vista Assemblée Pièce 1 À Rail DU Quincaillerie LA DE VUEMANQUANTES? Pièces Recommandés Outils Recomendadas Herramientas 11 .Pg / .Pág 18-17 .Pg 12 .Pg / .Pág14 .Pg OU / OAluminium, léger, acier en plaques des Section la à reporter se installée fois uneElle-t-a section a garage de porte Votre Section à référer Se .librement4 Secciones las a Refiérase Índice Matières DES TableSeguridad DE Características Abridor DEL CaracterísticasMobiles pièces Terre la à mis correctement être doit l’ouvreurMouvement Beltliftchainlift

1042 specifications

The Genie 1042 is a versatile and efficient aerial work platform designed to meet the demands of various industries, from construction to maintenance and operations. This compact boom lift is renowned for its remarkable lifting capabilities and user-friendly features, making it a favorite among professionals seeking reliability and performance.

One of the standout features of the Genie 1042 is its impressive working height, reaching up to 40 feet, and a horizontal outreach of 22 feet. This combination of height and reach makes it ideal for tasks that require working at significant elevations while still maintaining a solid base. The platform extends and retracts smoothly, providing operators with the flexibility to navigate around obstacles and access hard-to-reach areas effectively.

Powered by an efficient electric motor, the Genie 1042 operates quietly, making it suitable for indoor use and residential areas where noise restrictions may be a factor. The electric motor also offers zero emissions, aligning with modern environmental standards and preferences for greener equipment. Its compact design, with a width of just 4 feet, allows it to maneuver easily through standard doorways and tight spaces, enhancing its practicality on job sites.

Safety is a priority with the Genie 1042, featuring an intuitive operator control system and standard safety measures, including a tilt sensor and emergency stop buttons. The platform is equipped with guardrails, ensuring operator security while working at height. The sturdy construction of the Genie 1042 also contributes to stability, enabling users to focus on their tasks without worrying about the integrity of the lift.

Additionally, Genie has incorporated advanced technologies into the 1042 model, including a diagnostics system that provides real-time feedback on the machine's performance. This feature enhances maintenance efficiency, allowing operators to monitor the health of the platform and address potential issues proactively.

In summary, the Genie 1042 embodies a combination of height, outreach, and compactness, backed by reliable electric power, advanced safety features, and intelligent technology. Whether used in construction, maintenance, or any other sector requiring elevated work, the Genie 1042 proves to be a formidable tool that enhances productivity while prioritizing operator safety and environmental responsibility.
Top Page Image Contents