Genie 1042 manual Do not USE AN Extension Cord

Page 4

PRE-INSTALLATION CHECK LIST FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM

Things to consider if you are planning to "Do-it-yourself." This opener is designed for use with SECTIONAL doors only.

In many cases you will be replacing an existing door opener with a new one, however, if this will be the first opener installed there are some pre-installation issues which need to be addressed. They are as follows:

The Genie Company recommends that you read and fully understand all information and instructions contained herein before choosing a "Do-it-yourself" installation. Any questions should be directed to The Genie Company or an authorized Genie® Dealer.

(The issue numbers below refer to the circled numbers in the illustrations on page 5.)

1Check your ceiling where the power head of your new unit will be mounted.

Plan how you will be mounting the power head. It is possible that ceiling joists may not be in the position needed with respect to the garage door opener. It may be necessary to add an additional bracket and fasteners (not included with your new door opener kit).

(Refer to Section 2.)

2Check the wall directly above the garage door. The door opener’s header bracket

must be securely fastened to this wall. Insure that the structure will provide a strong mounting location. (Refer to Section 2.)

3Check to see if the mounting location

for the Safe-T-Beam®System is clear from

obstruction and has a wood surface available for attaching the mounting brackets. The brackets may be attached to concrete if necessary but extra tools and special fasteners (not supplied) will be required. (Refer to Section 4 and 5.)

5You need a properly grounded 110-120 Volt power supply available. The outlet should be

no more than 3 feet from the power head once it is mounted. (Refer to Section 5.)

WARNING

DO NOT USE AN EXTENSION CORD!

DO NOT USE A PORTABLE GENERATOR! This product is designed to operate on standard house current.

DO NOT USE ALTERNATE POWER SUPPLIES.

6To avoid damage to your door and/or opener, make sure you disable and/or

remove any door locks, ropes, and/or cables (NOT door lift cables) prior to installing your opener. (Refer to Section 1.)

Remove

Remove

7Insure that your door is properly balanced and moving freely. (Refer to Section 2.)

NOTE: Mounting brackets must be installed within code specifications.

4Is your sectional garage door made of aluminum, light-weight steel, fiberglass

or glass panels? Additional support bracing must be added to these type doors. If this is the case, please contact the door manufacturer or authorized dealer so that they can furnish you with a "bracing kit." (Refer to Section 2.)

WARNING

To reduce the risk of injury to persons or damage to property - Use this opener only with sectional doors.

WARNING

If your door jams, binds, is improperly balanced or has a broken spring, have it repaired or adjusted by a trained door system technician. Door springs, cables, pulleys, brackets and associated hardware are under extreme tension and can cause serious injury or death.

8(NOT SHOWN) If your garage does not have a separate entry door, you should consider

an emergency release kit (GER-2) for installation on your garage door. (See emergency release kit installation notes on page 21.)

4

PN# 36420Supplement, 10/27/2008

 

Image 4
Contents CHAINLIFT/BELTLIFT Models 1022/1024/1042 Turn OFF power before removing operator cover System technician using proper tools and instructionsKeep people clear of opening while door is moving Do not allow children to play with the door operatorOpener Features Table of ContentsSafety Features Do not USE AN Extension Cord Typical Sectional Door Installation Pg PgRecommended Tools Parts Identification Not Shown Full SizeDo not Return to Point of Purchase Chain Piece Rail Hardware Assembled ViewImportant Installation Instructions Opener AssemblyChain Power Head & Rail Assembly Use 16-18 x 1/2 BoltsFinding header bracket mounting location Installation Header and Door Mounting BracketsDo not move door spring Mounting the header bracket Mounting the assembly Mounting the OpenerGetting started Attach angle iron to beamsInstall Door Arms Door BracketWall Button Installation 2a. Wiring If pre-wired2b. Wiring If not pre-wired Wall Button locationDo not install rear cover yet Securely fasten wiresMounting 3a. Wiring If not pre-wired SAFE-T-BEAMSYSTEM InstallationMounting Safe-T-BeamSource Red LED and Sensor Green LED Route Safe-T-Beamwires through wire guide 3b. Wiring pre-wiredDo not install the white lamp cover at this time Connecting to Power With Permanent WiringWith Power Supplied With Grounded PlugDoor Limits Setting & Testing OPEN/CLOSE LimitsClose Travel Limit Keyed Emergency Release Carriage LockKeyed Emergency Release Operation Instructions Erase OPEN/CLOSE Travel Limit UP/DOWN ForceContact Reverse Test Programming Remote Controls Lost or Stolen RemoteLight BULB/LENS Installation Battery replacementVisor clip Light bulbMaintenance Routine Monthly MaintenanceDoor balance Contact reverseCircuit Wiring Diagram Advertencia AvertissementTroubleshooting Guide Operation Problem What to doTroubleshooting Guide Power Head LED Possible Problem SolutionTransmitter Compliance Statement Page This page left blank Solution Possible Problème ClignoteSolución Problema Posible Fonctionnement Dépannage DE Guide Funcionamiento DE Problema Averías DE Investigación DE Guía Del funcionamiento MalAvertissement Maintenance AdvertenciaMantenimiento Rutina DEAvertissement Lentille la Fixer Lente la AprieteViseur du clip le Fixer Visera de sujetador el Acople Pile la’IC DE ET FCC LA DE Reglementation LA a Conforme Robado O Perdido RemotoRemotos Controles DE Programación BotónInverso Contacto DE Prueba Cerrar ABRIR/ DE Recorrido DEL Límite BorrarHAUT/BAS Force Puerta la de vano Del centro del debajo 4 xAvertissement Advertencia CLÉSecours DE Déverrouillage CON Pestillo DE PicaporteAdvertencia Puerta LA DE LímitesABRIR/CERRAR Corredizo al cadena la EngranaProtección DE Función InfrarrojaTension Sous Garde EN Mise PrecauciónGarde EN Mise PrecauciónArrière couvercle le Installer Posterior tapa la InstaleCouvercle du Clips Tapa la de PresillasFuente y detector Del alambrado de Métodos Beam-T-Safe del Fuente y detector del LugaresMontaje de Soportes Soportes Los a detectores los AcoplePuerta la de marco el Marque Coinçage MuraleMontaje MontagePared DE Control DEL Instalación Dénudage et DivisionPelando y Partiendo Pared de control Del alambre de RecorridoPuerta LA DE Soporte ’OUVREUR DE Montage Installation InstalaciónRiel DEL 10/27/2008 36420Supplement, PN#Cadena la de Ajuste Control De caja la de Conjunto RielRiel de partidas Secciones Partido riel del ConjuntoPORTE-OUVRE pour rail de Ensemble ’OUVREUR Abridor DEL ConjuntoLa de l’ouvreur installer possible, du mesure la Dans De risque de d’AVERTISSEMENT l’étiquette PlacerAssemblée Pièce 1 À Rail DU Quincaillerie LA DE VUE Pieza 1 DE Riel DEL Herrajes DE Montaje DEL VistaMANQUANTES? Pièces Recommandés Outils Recomendadas Herramientas 12 .Pg / .Pág 11 .Pg / .Pág 18-17 .Pg14 .Pg OU / OSection la à reporter se installée fois une Aluminium, léger, acier en plaques desElle-t-a section a garage de porte Votre Section à référer Se .librement4 Secciones las a Refiérase Matières DES Table ÍndiceSeguridad DE Características Abridor DEL CaracterísticasMobiles pièces Terre la à mis correctement être doit l’ouvreurMouvement Beltliftchainlift

1042 specifications

The Genie 1042 is a versatile and efficient aerial work platform designed to meet the demands of various industries, from construction to maintenance and operations. This compact boom lift is renowned for its remarkable lifting capabilities and user-friendly features, making it a favorite among professionals seeking reliability and performance.

One of the standout features of the Genie 1042 is its impressive working height, reaching up to 40 feet, and a horizontal outreach of 22 feet. This combination of height and reach makes it ideal for tasks that require working at significant elevations while still maintaining a solid base. The platform extends and retracts smoothly, providing operators with the flexibility to navigate around obstacles and access hard-to-reach areas effectively.

Powered by an efficient electric motor, the Genie 1042 operates quietly, making it suitable for indoor use and residential areas where noise restrictions may be a factor. The electric motor also offers zero emissions, aligning with modern environmental standards and preferences for greener equipment. Its compact design, with a width of just 4 feet, allows it to maneuver easily through standard doorways and tight spaces, enhancing its practicality on job sites.

Safety is a priority with the Genie 1042, featuring an intuitive operator control system and standard safety measures, including a tilt sensor and emergency stop buttons. The platform is equipped with guardrails, ensuring operator security while working at height. The sturdy construction of the Genie 1042 also contributes to stability, enabling users to focus on their tasks without worrying about the integrity of the lift.

Additionally, Genie has incorporated advanced technologies into the 1042 model, including a diagnostics system that provides real-time feedback on the machine's performance. This feature enhances maintenance efficiency, allowing operators to monitor the health of the platform and address potential issues proactively.

In summary, the Genie 1042 embodies a combination of height, outreach, and compactness, backed by reliable electric power, advanced safety features, and intelligent technology. Whether used in construction, maintenance, or any other sector requiring elevated work, the Genie 1042 proves to be a formidable tool that enhances productivity while prioritizing operator safety and environmental responsibility.