Genie 1042 Connecting to Power, With Grounded Plug, With Permanent Wiring, With Power Supplied

Page 19

5CONNECTING TO POWER

WARNING

To reduce the risk of electrical shock, this equipment has a grounded type plug that includes a third (grounding) pin. This plug will only fit a grounded type outlet. If you do not have a grounded outlet, contact a qualified licensed electrician to install one. DO NOT alter the plug in any way. The door opener must be properly grounded in order to prevent personal injury and damage to the components.

DO NOT remove motor cover. All work performed on motor must be done by a trained door system technician.

CAUTION

Check local building codes to make sure that you are not required to have your garage door opener permanently wired, with circuit breaker protection. If building codes require door opener to be permanently wired have a qualified licensed electrician connect power with permanent wiring.

WITH GROUNDED PLUG:

Plug the opener into a properly grounded electrical outlet (Fig. 5-1).

WITH PERMANENT WIRING:

Instructions for Electrician.

Remove power from circuit.

Remove rear cover and motor cover.

Remove four motor cover screws (Fig. 5-2).

Remove existing power cord and strain relief from the 7/8" dia. hole and discard (Fig. 5-3).

Connect permanent wiring to power head using 7/8" diameter hole.

White to white/black to black/ground to green.

Use only UL recognized wire nuts.

Wires inside the power head must be at least 6" in length.

Replace motor cover and rear cover and re-energize the circuit.

NOTE: The Genie Company is not responsible for charges resulting from work preformed by an independent electrician.

WITH POWER SUPPLIED:

Check Safe-T-Beam®alignment (Fig. 5-4).

Insure that no part of door or its hardware is in path between lenses of source and sensor.

Insure that tops of lenses are between 5" - 6" above the floor (Fig. 5-4). The brackets are flexible, and can be adjusted slightly if needed.

Adjust the Red LED transmitter by aiming the unit directly at the Green LED receiver. Use the adjustment screw located on the top of the transmitter housing to make adjustments.

The Red LED transmitter will blink if there is a misalignment. When the LED units are aligned the Red LED will remain ON continuously.

After the alignment is finished tighten the adjustment screws on both sensors.

FOR HELP-1.800.354.3643 OR WWW.GENIECOMPANY.COM

FIG. 5-1 Connect to power.

Motor Cover Screws

FIG. 5-2 Remove motor cover.

FIG. 5-3 Power cord strain relief.

CAUTION

Do NOT use an extension cord.

Do NOT use a portable generator. This product is designed to operate using standard household current.

Do NOT use alternate power supplies.

 

 

 

 

o

m

fl

o

o

r

 

 

 

fr

r

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

6

" m

ax

om

fl

o

o

 

 

 

 

 

 

 

 

 

in

fr

 

 

 

 

 

 

5" m

 

 

 

 

 

 

 

FIG. 5-4 Check Safe-T-Beam®alignment.

INFRARED PROTECTION FUNCTION

1.When the garage door is opening, its movement will not be influenced if the Safe-T-Beam®is obstructed.

2.If the Safe-T-Beam®is obstructed before the garage door fully closes, the door will not close.

3.When the garage door is closing, if Safe-T-Beam®is cut off by people or obstacle, the garage door will reverse automatically to its fully opened position. (Meanwhile, the opener light will keep blinking until door moves to its fully opened position.)

4.If the Safe-T-Beam®System fails, loses power, or is installed improperly, you will have to press and hold the Wall Button "close" button until the door reaches its fully closed position. The LED indicator light on the power head will be green and blink twice (Pattern: ☼☼ pause ☼☼ pause) to inform you to eliminate problem first. Otherwise, the door will reverse automatically to its fully opened position if you release the "close" button on the Wall Button during the closing movement.

PN# 36420Supplement, 10/27/2008

19

 

Image 19
Contents CHAINLIFT/BELTLIFT Models 1022/1024/1042 Do not allow children to play with the door operator Turn OFF power before removing operator coverSystem technician using proper tools and instructions Keep people clear of opening while door is movingOpener Features Table of ContentsSafety Features Do not USE AN Extension Cord Pg Pg Typical Sectional Door InstallationParts Identification Not Shown Full Size Recommended ToolsDo not Return to Point of Purchase Piece Rail Hardware Assembled View ChainOpener Assembly Important Installation InstructionsChain Use 16-18 x 1/2 Bolts Power Head & Rail AssemblyFinding header bracket mounting location Installation Header and Door Mounting BracketsDo not move door spring Mounting the header bracket Attach angle iron to beams Mounting the assemblyMounting the Opener Getting startedDoor Bracket Install Door ArmsWall Button location Wall Button Installation2a. Wiring If pre-wired 2b. Wiring If not pre-wiredDo not install rear cover yet Securely fasten wiresMounting 3a. Wiring If not pre-wired SAFE-T-BEAMSYSTEM InstallationMounting Safe-T-BeamSource Red LED and Sensor Green LED Route Safe-T-Beamwires through wire guide 3b. Wiring pre-wiredDo not install the white lamp cover at this time With Grounded Plug Connecting to PowerWith Permanent Wiring With Power SuppliedDoor Limits Setting & Testing OPEN/CLOSE LimitsClose Travel Limit Keyed Emergency Release Carriage LockKeyed Emergency Release Operation Instructions Erase OPEN/CLOSE Travel Limit UP/DOWN ForceContact Reverse Test Lost or Stolen Remote Programming Remote ControlsLight bulb Light BULB/LENS InstallationBattery replacement Visor clipContact reverse MaintenanceRoutine Monthly Maintenance Door balanceAdvertencia Avertissement Circuit Wiring DiagramProblem What to do Troubleshooting Guide OperationPossible Problem Solution Troubleshooting Guide Power Head LEDTransmitter Compliance Statement Page This page left blank Clignote Solution Possible ProblèmeSolución Problema Posible Fonctionnement Dépannage DE Guide Del funcionamiento Mal Funcionamiento DE Problema Averías DE Investigación DE GuíaRutina DE Avertissement MaintenanceAdvertencia MantenimientoAvertissement Pile la Lentille la FixerLente la Apriete Viseur du clip le Fixer Visera de sujetador el AcopleRobado O Perdido Remoto ’IC DE ET FCC LA DE Reglementation LA a ConformeBotón Remotos Controles DE ProgramaciónPuerta la de vano Del centro del debajo 4 x Inverso Contacto DE PruebaCerrar ABRIR/ DE Recorrido DEL Límite Borrar HAUT/BAS ForceCON Pestillo DE Picaporte Avertissement AdvertenciaCLÉ Secours DE DéverrouillageCorredizo al cadena la Engrana AdvertenciaPuerta LA DE Límites ABRIR/CERRARProtección DE Función InfrarrojaTension Sous Precaución Garde EN MisePrecaución Garde EN MiseTapa la de Presillas Arrière couvercle le InstallerPosterior tapa la Instale Couvercle du ClipsBeam-T-Safe del Fuente y detector del Lugares Fuente y detector Del alambrado de MétodosMontaje de Soportes Soportes Los a detectores los AcoplePuerta la de marco el Marque Montage CoinçageMurale MontajePared de control Del alambre de Recorrido Pared DE Control DEL InstalaciónDénudage et Division Pelando y PartiendoPuerta LA DE Soporte ’OUVREUR DE Montage Instalación InstallationControl De caja la de Conjunto Riel Riel DEL10/27/2008 36420Supplement, PN# Cadena la de AjusteRiel de partidas Secciones Partido riel del ConjuntoPORTE-OUVRE pour rail de Ensemble Abridor DEL Conjunto ’OUVREURDe risque de d’AVERTISSEMENT l’étiquette Placer La de l’ouvreur installer possible, du mesure la DansPieza 1 DE Riel DEL Herrajes DE Montaje DEL Vista Assemblée Pièce 1 À Rail DU Quincaillerie LA DE VUEMANQUANTES? Pièces Recommandés Outils Recomendadas Herramientas OU / O 12 .Pg / .Pág11 .Pg / .Pág 18-17 .Pg 14 .PgSection à référer Se .librement Section la à reporter se installée fois uneAluminium, léger, acier en plaques des Elle-t-a section a garage de porte Votre4 Secciones las a Refiérase Abridor DEL Características Matières DES TableÍndice Seguridad DE CaracterísticasMobiles pièces Terre la à mis correctement être doit l’ouvreurMouvement Beltliftchainlift

1042 specifications

The Genie 1042 is a versatile and efficient aerial work platform designed to meet the demands of various industries, from construction to maintenance and operations. This compact boom lift is renowned for its remarkable lifting capabilities and user-friendly features, making it a favorite among professionals seeking reliability and performance.

One of the standout features of the Genie 1042 is its impressive working height, reaching up to 40 feet, and a horizontal outreach of 22 feet. This combination of height and reach makes it ideal for tasks that require working at significant elevations while still maintaining a solid base. The platform extends and retracts smoothly, providing operators with the flexibility to navigate around obstacles and access hard-to-reach areas effectively.

Powered by an efficient electric motor, the Genie 1042 operates quietly, making it suitable for indoor use and residential areas where noise restrictions may be a factor. The electric motor also offers zero emissions, aligning with modern environmental standards and preferences for greener equipment. Its compact design, with a width of just 4 feet, allows it to maneuver easily through standard doorways and tight spaces, enhancing its practicality on job sites.

Safety is a priority with the Genie 1042, featuring an intuitive operator control system and standard safety measures, including a tilt sensor and emergency stop buttons. The platform is equipped with guardrails, ensuring operator security while working at height. The sturdy construction of the Genie 1042 also contributes to stability, enabling users to focus on their tasks without worrying about the integrity of the lift.

Additionally, Genie has incorporated advanced technologies into the 1042 model, including a diagnostics system that provides real-time feedback on the machine's performance. This feature enhances maintenance efficiency, allowing operators to monitor the health of the platform and address potential issues proactively.

In summary, the Genie 1042 embodies a combination of height, outreach, and compactness, backed by reliable electric power, advanced safety features, and intelligent technology. Whether used in construction, maintenance, or any other sector requiring elevated work, the Genie 1042 proves to be a formidable tool that enhances productivity while prioritizing operator safety and environmental responsibility.