Mitsubishi Electronics TG-2000A Appendix 1 Installing Windows XP Professional, Setup Procedure

Page 94

Appendix 1: Installing Windows XP Professional

This chapter assumes that Windows XP Professional is to be installed on a PC on which Windows XP Professional is not installed. Therefore, you can skip this chapter when Windows XP Professional is already installed on the PC.

Note:

The installation method may vary depending on the PC.

1.Preparing for Se tup

What you need

Microsoft Windows XP Professional CD-ROM

Note:

If Windows XP Professional is installed on a PC already in use, important data may be destroyed. Therefore, keep the backup beforehand.

2.Setup Procedure

1)Insert Windows XP Professional CD-ROM into CD-ROM drive and turn on the computer.

When the CD-ROM is started, the messages such as "Press any key boot from CD" may be displayed depending on the type of personal computer used. If so, start the CD-ROM in accordance with the message.

2)After the files are copied, a screen entitled “Welcome to setup” appears. Select the option “To setup Windows XP now” and press Enter.

3)The Windows XP license agreement will then appear. Use Page Down to read it all. To accept the license conditions and continue, press the “F8” key.

4)If Setup finds Windows XP already on the hard disk, the following options appear. “To repair the selected Windows XP installation, press R.”

“To continue installing a fresh copy of Windows XP without repairing, press ESC” In this case, select “Fresh copy” and press the ESC key.

5)Select the type of keyboard. If a Japanese keyboard is used, press the [Single-byte/double-byte] key.

6)With the above step, the keyboard confirmation is displayed. Press the [Y] key.

7)You will be asked to select which partition to install Windows XP on. Select the partition and press Enter.

8)When the following message was displayed,

“To continue Setup using this partition, press C.” “To select a different partition, press ESC.”

Press “C” to continue Setup. (When ESC was pressed, Setup returns to Step 7) . )

9)You will be asked which file system (FAT, NTFS) you want to use. Select the file system that you want (the item is inverted when selected) and press Enter.

The following describes when NTFS is selected. Select “Format the partition using the NTFS file system”.

10)A message to indicate the drive is ready to be formatted appears. “To format the drive, press F.”

“To select a different partition for Windows XP, press ESC.”

Press the “F” key to start formatting the drive. (When ESC was pressed, Setup returns to Step 7).)

91

Image 94
Contents Please read this manual before using the unit Please keep this manual for future useContents Page Other machines Safety PrecautionsDo not use with other applications Compatible Units System Requirements Requirements system recommendations¡ *1 Number of units RestrictionsRestrictions Other Devices M e Manufacturer ModelSystem Configuration System Configuration Example Hardware Connection DiagramPC connections and settings Flow of Site AdjustmentTools for Site Adjustment 50A test runTest operation from centralized controller G-50A D e l s IP address rangePage Preparing for installation InstallationG-2000A Setup Steps Action Details How toDatabase setup Running TG-2000A Setup New setupMsde setup When the installation is completed, restart the computerTG-2000A setup completion Check the installation folderInstallation start confirmation Read the license agreementTG-2000A uninstall G-2000A UninstallMsde uninstall Part Names and Functions Window Elements Shift from the initial window to the control window Accessing Functions and Moving between WindowsBasic Mouse Operation Shift from the control window to the initial windowPage Page User Set -up Set TG -2000A functions Page Page Initial Startup and Shutdown Before Startup StartupTG-2000A Shutdown ShutdownShutting down the OS System Setting Procedure System Setting Screen System Setting ProcedureUser Set-up General OperationConnection Setting Reliability FunctionEnergy Monitoring Related Site Name Set-upPage Number of G-50A se t-up Step Setting Procedure and RestrictionsG-50 Connection Set-up IP address of G-50A se t-up StepSystem Configuration Set-up Monitor the optional functions being used. Procedure2 G-50A data collection Step Unit composition set-up StepChange the unit configuration. Procedure Icon Name Address rangeSe t-up of refrigerant system Step Set-up of group Step Interlocking ventilation unit Interlocked setting StepChange the group No. Procedure Interlocking destination un-set unitMonitoring Screen Set-up Configuration Procedure and RestrictionsSet-up of model name Step Set-up of the number of floors, and floor name Step Creation of a plane view Step Set-up of floor name and G -50Set the group icons on each floor and set their names Set-up of icon arrange and name StepFloor Selection Display Button Group ListSet-up of block Step Set the block groups. ProcedureDeleting block settings Name Change button Block Set button Release buttonChanging the block name Setting Procedures and Restrictions Check before WHM setup. ProcedureModel Baud rate Parity Stop bit Set Charge System options. Procedure Energy Monitoring S e t-upDivision mode for indoor unit Division mode StepDivision mode for outdoor unit Proportiona l division reference dataSelect the OC icon, and click on the selected outdoor unit Delete Watt Hour Meter RelationshipsSet the Indoor Unit and Watt Hour Meter Relationship Relation between indoor units and watt hour meters StepDeleting Watt Hour Meter Relationships Set the charge blocks. Procedure Charge Blocks StepRelease a block from charge blocks Delete the charge blockAdd charge blocks Exit the Currency Settings Selecting a Currency from the Display ProcedureManually Setting the Currency Set the electric power rate schedule. ProcedureSet the standard charge . Procedure 10Standard charge set StepSet the date/time . Procedure Function ContentsTime Set-up Monitor the time Monitor buttonPassword S e t-up Change the passwordNo repair is required Overview Remarks Maintenance Methods and Restrictions Maintenance of Charge DataPreparing for Charging Data Maintenance Display the Maintenance screen. ProcedureUnit Data Maintenance Maintaining Apportioned Unit DataCorrection method Maintenance example Watt Hour Meter Data Maintenance Maintaining watt hour Meter Data ProcedureOperation Amount Data Monitoring Watt hour Meter Monitor Function ProcedureDescription of function Monitoring operation amount data Charge Parameter OutputMonitor the data for the last day after Output file data format Charging RemedyPerforming charging remedy Preparing to perform charging remedy PreparationRemedial apportioning setting screen Apportioning integrated Remark InterValRemedial apportioning confirmation screen Calculating screen Remedy when personal computer HDD fails no backup Remedy when personal computer HDD fails backup Day before recovery day Apportioning method when computer crashes Remedy when watt hour meter fails monitoring impossible Integrate d Remedy for system information setting error Total air-conditioning charge including that Error Code List Air-conditioning unit error codesPage Page System error codes Setting item Case Setting Check ListDetail of function Test Run Check Test run check sheetLRC Date Tester Charging No WHM connection Test Run Check Charging Test Run CheckTest item Comment Page Capacity Check Within Outside Division mode Charge settingSetting TotalExample 1100 conditioner 1300 Outside Within 12001400 Page Page WHM1 WHM2 WHM3 WHM4 WHM5 WHM6 Memo Preparing for Se tup Appendix 1 Installing Windows XP ProfessionalSetup Procedure What you needPage Windows XP Appendix 2 Auto Log-in Confirmation MethodWindows Page WT03901X01