Use
Starting & Stopping R 43
Starting
1.Connect the spark plug lead.
2.Move the Engine Speed Control to the FAST ‘ 
’ position before starting.(G1)
3.Pull the operator presence control (OPC) to release the brake on the engine and the blade.(G2)
4.Pull the recoil starter fully towards you until you feel
the full resistance, return the handle slowly then pull the handle firmly towards you to its full extent.(G3)
5.After the engine has started, allow to run for 30
seconds before commencing to use.
Stopping
1.Release the OPC lever.(G2) THROTTLE CONTROL (if fitted)
1.Fig. G4 represents the FAST (run) position.
2.Fig. G5 represents the SLOW (idle) position.
Starting & Stopping R 43S Starting
1.Follow steps
2.Pull the operator presence control (OPC) to release the brake on the engine and the blade.(G6).
3.Follow steps
Engaging the Drive
1.Forward drive is engaged and disengaged with the Powerdrive lever at the top of the handle.(G7)
2.Releasing the Powerdrive Lever stops the
forward drive automatically.
Stopping
1.Release the powerdrive lever.(G7)
2.Release the OPC lever.(G6)
Starting & Stopping R 43SE Starting
1.Follow steps 1-3 for the R 43S
2.Turn the key and hold until the engine starts.(G8) The key will return to the original position when released.
3.If the engine fails to start when you turn the key
your battery may need charging.
Engaging the Drive - See R 43S
Stopping - See R 43S
How to Mow
•Due to engine lubrication limitations, the mower should not be used on slopes in excess of 30°.
1.Start mowing from the outside edge of the lawn, mowing in strips in alternate directions
2.Mow twice a week in the growing season, your lawn will suffer if more that one third of its length is cut at one time and this may also result in poor
collection.
Please Note:-
Do not overload your Lawnmower
When mowing in long thick grass a first cut with the
cutting height adjusted to its highest setting, see Cutting Height, will help reduce engine overload
and will help prevent damage to your lawnmower.
Cutting Height Adjustment
1.Pull the height adjustment lever away from the location slots and move it to the selected
position.(H).
Using as a mulcher
1.Your lawnmower is supplied with a mulching plug.
2.Stop your lawnmower as described in Use - starting and stopping, and disconnect the spark plug.
3.Lift safety flap. Twist and slide mulching plug into rear discharge chute. (J)
4.Ensure mulching plug is securely fitted. (K)
5.The mulching plug prevents grass from being collected by blocking the collection chute on the underside of the deck.
6.Ensure the safety flap is positioned correctly.
Maintenance
IMPORTANT
Release the Operator Presence Control, to stop the engine, wait until the blade has stopped and disconnect the spark plug lead:-
-before clearing a blockage;
-before checking, cleaning or working on the
appliance
IMPORTANT
Never use water for cleaning your lawnmower. Do not clean with chemical, including petrol, or solvents
-some can destroy critical plastic parts.
Cleaning
• Disconnect the spark plug lead.
• Turn machine on it’s side with the exhaust uppermost.
1. Remove grass from under the deck with a brush.(L1 and L2)
2. Using a soft brush - remove grass clippings from the engine air intakes and exhaust (L3), cutting height adjustment area, around the wheels (L4) and the grass collector.
3. Wipe over the surface of your lawnmower with a dry cloth.
Cutting System
Removing the Blade
•Disconnect the spark plug lead.
•Turn machine on it’s side with the exhaust uppermost.
1. Use spanner to loosen blade bolt by turning anti- clockwise.(M)
2. Remove the blade bolt, blade and spacer washer.
3. Inspect for damage and clean as necessary.
Fitting the Blade
1. Fit the blade to the machine with the sharp edges pointing away from the machine.
2.
3. Hold firmly and tighten blade bolt firmly with a
spanner. Do not over tighten.
IMPORTANT
Do not attempt any maintenance on your
lawnmower when the engine is hot.
Always handle the blade with care - sharp edges could cause injury. USE GLOVES. Renew your metal blade after 50 hours mowing or 2 years whichever is the sooner - regardless of condition. If the blade is cracked or damaged replace it with a new one.
ENGLISH - 4