Manuals
/
Brands
/
Communications
/
Telephone
/
NEC
/
Communications
/
Telephone
NEC
ND-71762(E) system manual
Please, tick the box below to download manual:
Contents
Main
Page
BEFORE THE USE OF THIS MANUAL
Page
DANGER
?
Page
WARNING
ATTENTION
WARNING
ATTENTION
Page
NEAX2400 IPX Internet Protocol eXchange No.7 CCIS System Manual
TABLE OF CONTENTS
Page
TABLE OF CONTENTS (CONTINUED)
Page
CHAPTER 1 INTRODUCTION
CHAPTER 2 GENERAL INFORMATION FOR CCIS
Page
Page
Page 5
Figure 2-3 Hardware Configuration of No. 7 CCIS System
<CCIS Digital Line>
<CCIS Analog Line>
CHAPTER 2 ND-71762 (E) Page 6
Figure 2-4 Example of Network Configuration for CCIS Digital Line
Page 7
Figure 2-5 Example of Network Configuration for CCIS Analog Line
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page 19
Figure 2-14 Diagram of Connections between M-OSC and PLO/OSC
Page
Page 21
Figure 2-15 Diagram of Connections between PLO/TSW and DTI
Page
Page
Page
Page 25
Centralized MAT
This figure shows an example of centralized functions activation.
Page
Page 27
Centralized MAT
NETWORK CONFIGURATION
FUG3
FUG4
FUG2 (Center FUG)
Page
CHAPTER 3 SWITCH SETTING SHEETS
CHAPTER 4 INSTALLATION PROCEDURE
Page
Page
Page
Page
Page
Page 36
Figure 4-5 LT Connector Leads Accommodation for DTI/CCT
Accommodated in *1
Accommodated in *2
Accommodated in *3
Page 37
Figure 4-6 PLO Pin Assignments for Receiving Clock (1-IMG System)
PIM0 PLO
Page 38
Figure 4-7 PLO Pin Assignment for Receiving Clock (4-IMG System)
REAR VIEW
34PH EXCLK CA-A
PLOEXCLK1
Page 39
Cable Connection Diagram
Page 40
Note: This diagram shows connections for a system having dual PLOs.
Page 41
Figure 4-10 Cable Connection Diagram for Receiving Clock from a Digital Interface (TSW)
Note 1: Note 2:
Page 42
Figure 4-11 Cable Connection Diagram for Receiving Clock from a Digital Interface (PLO)
IMG/ISWM
Note 2
Note 1:
Cable Connection Diagram
Note 1
MDF
IMG
3.4 Front Cable Connection between DTI and CCH
Note 1
Note 2
Page
Page
Page 46
Figure 4-15 Connection between PBX and MODEM
(a) Cable Connection when Accommodated in *1 (Refer to Figure 4-16)
(b) Cable Connection when Accommodated in *2 (Refer to Figure 4-16)
Page 47
Figure 4-15 Connection between PBX and MODEM (Continued)
(c) Cable Connection when Accommodated in *3. (Refer to Figure 4-16)
CHAPTER 4 ND-71762 (E) Page 48
Figure 4-16 LT Connector Leads Accommodation for 2CCH
Accommodated in *3
Accommodated in *1
Accommodated in *2
CHAPTER 5 INSTALLATION TEST PROCEDURE
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
CHAPTER 6 BASIC DATA ASSIGNMENT
ND-71762 (E) CHAPTER 6 Page 67
2. DATA ASSIGNMENT 2.1 Port Allocation and Related Command
2)
f
(R
Note
In this figure, five letters such as AAAAA, represent mounting location of CCT card or CCH card.
Page
CHAPTER 6 ND-71762 (E) Page 70
07/31/02
Page
Page
Page
Page
ND-71762 (E) CHAPTER 6 Page 75
Figure 6-2 CIC Number Assignment
Note: Press the SPACE bar to skip LEN and press the RETURN key.
Figure 6-3 Example of a CCIS Network (Tandem)
The CIC number must be identical between two nodes as shown below.
A sample office data assignment sheet for Node A is as follows.
Page
Page
Page
Page
Page
CHAPTER 7 CCIS SERVICE FEATURES
Page
Page
CHAPTER 8 MAINTENANCE PROCEDURE
Page
Page
ND-71762 (E) CHAPTER 8 Page 87
MAINTENANCE PROCEDURE
Figure 8-1 Circuit Card Mounting Location (1/2)
(a) MG and Unit configuration
1-IMG/4-IMG system
Note: LP (Local Partition Number), MG (Module Group Number) U (Unit Number)
(b) Group Configuration PIM
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
Page
3.3 Fault Repair Procedure for Digital CCIS Line
Page
Page
Page
Page
Page
Page
Page
NEAX2400 IPX Internet Protocol eXchange No.7 CCIS System Manual ND-71762(E)
NEAX2400 IPX Internet Protocol eXchange No.7 CCIS System Manual ND-71762(E)