Manuals / Brands / Communications / Telephone / NEC / Communications / Telephone

NEC ND-71762(E) CHAPTER 6 ND-71762 (E) Page 70, 07/31/02

1 138

Download 138 pages, 2.47 Mb

CHAPTER 6 ND-71762 (E)

Page 70

Issue 2

BASIC DATA ASSIGNMENT

Miscellaneous Data1) Index 186: b6 must be assigned as 1 (CCIS is in service). The remaining data should be determined depending on cus-tomer’s requirements.b0: 0/1 = CCIS Link Reconnection is not available/available. When either of the two parties that are engaged in a Station-to-Station/Station-to-Trunk/Trunk-to-Trunk con-nection via CCIS link transfers the call to another station, CCIS Link Reconnection will be provided. By es-tablishing new link after the call transfer, the most proper routing can be provided for the two parties whichare eventually connected. Note 3, Note 4

0

b7

1

b6

0

b5

1

b4

0

b3

0

b2

1

b1

1

b0

Example (Index 186)

Station A

Station A

Station C

Station C

Station B

Station B

(1) Station A made a call to Station B

(1) Station A made a call to Station B

(2) Station B transferred the call to StationC

Link a

Link b

Link c

(3) Station B transferred the call to Station C

Node A Node B

Node A Node B

(4) Link Reconnection is provided between Station A and C, by using Link c.

At this time, LInk a and b are released.

(4) Link between Station A and C is reestablished, and Link between Node A and B is released.

Exmaple 1:

1. A call between Station A and B is established.

2. Station B transfers the call to Station C.

3. After connecting to Station C, Station B hungs up.

4. Link between Station A and C is reestablished. At this time Link between Node A and B is released.

Exmaple 2:

1. A call between Station A and Station B is established.

2. Station B transfers the call to Station C.

3. After connecting to Station C, Station B hungs up.

4. Link c (between Station A and C) is reestablished. at this time, Link a and b are released.

In the following cases, Link Reconnection is provided:

(3) Station B hungs up

(3) Station B hungs up

07/31/02

Contents

Main Page BEFORE THE USE OF THIS MANUAL Page DANGER ? Page WARNING ATTENTION WARNING ATTENTION Page NEAX2400 IPX Internet Protocol eXchange No.7 CCIS System Manual TABLE OF CONTENTS Page TABLE OF CONTENTS (CONTINUED) Page CHAPTER 1 INTRODUCTION CHAPTER 2 GENERAL INFORMATION FOR CCIS Page Page Page 5 Figure 2-3 Hardware Configuration of No. 7 CCIS System <CCIS Digital Line> <CCIS Analog Line> CHAPTER 2 ND-71762 (E) Page 6 Figure 2-4 Example of Network Configuration for CCIS Digital Line Page 7 Figure 2-5 Example of Network Configuration for CCIS Analog Line Page Page Page Page Page Page Page Page Page Page Page Page 19 Figure 2-14 Diagram of Connections between M-OSC and PLO/OSC Page Page 21 Figure 2-15 Diagram of Connections between PLO/TSW and DTI Page Page Page Page 25 Centralized MAT This figure shows an example of centralized functions activation. Page Page 27 Centralized MAT NETWORK CONFIGURATION FUG3 FUG4 FUG2 (Center FUG) Page CHAPTER 3 SWITCH SETTING SHEETS CHAPTER 4 INSTALLATION PROCEDURE Page Page Page Page Page Page 36 Figure 4-5 LT Connector Leads Accommodation for DTI/CCT Accommodated in *1 Accommodated in *2 Accommodated in *3 Page 37 Figure 4-6 PLO Pin Assignments for Receiving Clock (1-IMG System) PIM0 PLO Page 38 Figure 4-7 PLO Pin Assignment for Receiving Clock (4-IMG System) REAR VIEW 34PH EXCLK CA-A PLOEXCLK1 Page 39 Cable Connection Diagram Page 40 Note: This diagram shows connections for a system having dual PLOs. Page 41 Figure 4-10 Cable Connection Diagram for Receiving Clock from a Digital Interface (TSW) Note 1: Note 2: Page 42 Figure 4-11 Cable Connection Diagram for Receiving Clock from a Digital Interface (PLO) IMG/ISWM Note 2 Note 1: Cable Connection Diagram Note 1 MDF IMG 3.4 Front Cable Connection between DTI and CCH Note 1 Note 2 Page Page Page 46 Figure 4-15 Connection between PBX and MODEM (a) Cable Connection when Accommodated in *1 (Refer to Figure 4-16) (b) Cable Connection when Accommodated in *2 (Refer to Figure 4-16) Page 47 Figure 4-15 Connection between PBX and MODEM (Continued) (c) Cable Connection when Accommodated in *3. (Refer to Figure 4-16) CHAPTER 4 ND-71762 (E) Page 48 Figure 4-16 LT Connector Leads Accommodation for 2CCH Accommodated in *3 Accommodated in *1 Accommodated in *2 CHAPTER 5 INSTALLATION TEST PROCEDURE Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page CHAPTER 6 BASIC DATA ASSIGNMENT ND-71762 (E) CHAPTER 6 Page 67 2. DATA ASSIGNMENT 2.1 Port Allocation and Related Command 2) f (R Note In this figure, five letters such as AAAAA, represent mounting location of CCT card or CCH card. Page CHAPTER 6 ND-71762 (E) Page 70 07/31/02 Page Page Page Page ND-71762 (E) CHAPTER 6 Page 75 Figure 6-2 CIC Number Assignment Note: Press the SPACE bar to skip LEN and press the RETURN key. Figure 6-3 Example of a CCIS Network (Tandem) The CIC number must be identical between two nodes as shown below. A sample office data assignment sheet for Node A is as follows. Page Page Page Page Page CHAPTER 7 CCIS SERVICE FEATURES Page Page CHAPTER 8 MAINTENANCE PROCEDURE Page Page ND-71762 (E) CHAPTER 8 Page 87 MAINTENANCE PROCEDURE Figure 8-1 Circuit Card Mounting Location (1/2) (a) MG and Unit configuration 1-IMG/4-IMG system Note: LP (Local Partition Number), MG (Module Group Number) U (Unit Number) (b) Group Configuration PIM Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page 3.3 Fault Repair Procedure for Digital CCIS Line Page Page Page Page Page Page Page NEAX2400 IPX Internet Protocol eXchange No.7 CCIS System Manual ND-71762(E) NEAX2400 IPX Internet Protocol eXchange No.7 CCIS System Manual ND-71762(E)