Control In/Chain-in, Gnd | ADTRAN TSU 600 specs

Chapter 2. Installation

Control In/Chain-in

This is used as an RS-232 port for connection to a computer or modem (Control In) or to another TSU 600 or TSU 100 (Chain-in). See Table 2-B for the pinout for the control/chain-in connector.

Connections

The chain-in connections are as follows:

Connector type		RJ-48
Part number		AMP# 555164-2
		Table 2-B
		Control In/Chain-in Pinout

PIN	NAME	DESCRIPTION

1	GND	Ground - connected to unit chassis

2	RTS	Request to send - flow control

3	RXDATA	Data received by the TSU 600

4	UNUSED

5	TXDATA	Data transmitted by the TSU 600

6,7	UNUSED

8	CTS	Clear to send-flow control

61200.076L2-1

TSU 600 User Manual

31

Image 43

ADTRAN TSU 600 user manual Control In/Chain-in, Gnd

Contents

Part Number 1200076L2 1200076L2#DC TSU Table of Contents Service Type Table of Contents Table of Contents Installation Operation Table of Contents Example Operations Figures 15. Drop and Insert, Voice, and Bridging Application Set Up Tables T1/FT1 Overview T1 Service Offerings Fractional T1 Functional Description TSU 600 OverviewFront View of the TSU Introduction TSU 600 Rear Panel Identification of Rear Panel Layout Features of the TSU Network Interface TSU InterfacesTSU 600 Interfaces Chain Port Output Control Port Input Snmp Three Methods of ControlFront Panel Adtran PC Program Slot Option Slot ArrangementSlots TSU 600 Option Slot Arrangement Secondary Interfaces SI Option PortsOther Data Interfaces Network Timed TSU 600 Clock SourcesNetwork Timed Clock Source DTE Clock Source DTE Timed Internal Clock Source Internal Timing Normal CSU Timing Self Tests TSU 600 TestingLoopback Tests Network Loopback Tests TSU Port Interface Loopback DTE Interface Loopback Pattern Generation Bridge, PBX, Video Conferencing Application TSU 600 Configuration ApplicationsBridge, PBX, Video Conferencing Application Set Up TSU 600 Option Modules All Voice Application All Voice Application Set Up Variations of Mixed Applications Drop and Insert, Voice, and Bridging Application Variations of Mixed Applications Shipped by Adtran UNPACK, INSPECT, Power ConnectionProvided by Customer Power Connection Warranty and Customer Service Grounding Instructions UL Installation Network WiringNetwork Pinout GND Control In/Chain-in Chain-out Pinout Chain-out Self Test Power UP Testing and Initialization To Establish a Passcode Set User Passcode No Passcode Desired Set Unit Identification Control In PC Set Control Port Example of Chain-in Correct Passcode Normal Power-Up Procedure Identification of Front Panel Layout Operation TSU TSU 600 Front Panel Layout Alarm red Used in various menus to clear data/result fields Select a Menu Item General Menu Operation Sample Submenu Display and Data Fields Data Port Identification Module Slots, TSU Four Opening Menus Menu Structure Display of Opening Menus Opening Menu Functions Shows status of incoming commands on the chain-in port Displays and can be used to set the time and date Opening Menu Functions Detailed Discussion Complete Status Menu Status 1NI Perf Rpts Network Performance Reports NI Perf RptsNetwork Interface Performance Report Network Interface Errors NI Errors Network Interface Error Type Active Alarms Port Status View History Remote Port Complete Configuration Menu Configuration Config D4 is equivalent to superframe format SF YEL AlarmNetwork NI Format Inband Lpbck Xmit PRMClock Source SET LBO CTL Port AccessTraps OFF Map Exchange Selection DisplayAuto Selection Times for Map Exchange DS0 Map Designations Create Temp Copy a Temp Review MAP AB Create Temp Selection Screen Review Temp Selected Port and Quantity of DS0sEdit Temp Apply Temp a Port Configuration Port Configuration Port Config Complete Utility Menu Tree Utility Util Time/Date Factory Restore Set Passcode Unit ID ID Software Revision Software Rev Port Utility Complete Test Menu Test Network Tests Remote Loopbck Qrss always runs at 64K/DS0 All zeros Since the start of testing Bit errorThan 1 bit error and less than Than 320 bit errors Run Selftest Port Tests Cancel Tests Operation Example of Voice and Data Mix Voice and Data MIX Prior to Step Steps to SET UP Voice and Data MIXConfigure the Network Configuration for Network Interface Configuration for DTE Port Configure DTE Port 1.1 Nx56/64 From Option ModuleSelect the number of DS0s/Port12 Configuration for DS0 Map Complete the DS0 Map ConfigurationNx56/64 First Two Configuration Menu Items Complete a Configuration Table for the DSX-1 PBX PassthruActivate Configuration Menu Configuration for DSX-1 PBX Passthru First Two Network NI Configuration Menu Items Configuring the Network Interface First Two Network NI Menu Items DS0 Map a and Map B Configuration Menu Items Configuring the DS0 MAPCreate Map Menu with Displayed DS0 Number Display of DS0 Port Name Passthru Selection Field Example Operations Review Temporary MAPReview Screen Window Showing Edit Temp Option Edit Window Showing the Error Window Showing Port Configuration Option Configuring the PortsScreen Used To Change Mode Example Operations Far End Looped Back Test Testing Example 101 Test Menu One Four Test Submenu Windows Test Pattern Screen for Qrss all DS0s Screen that Appears During Loopback Verification SES Pressing the 2 key results in injecting errors Test Termination 106 Appendix a Figure A-1 TSU 600 Complete Menu Tree DTE Data Rate Chart DTE RATE=56K DTE RATE=64K DTE Data Rate vs. DS0s Configure Network Appendix C System Configuration Charts Select number of DS0s/PORT Configure DTE Port 1.1 Nx56/64Configuration Chart for DTE Port Rate Chart DS0 Map B Configuration DS0 Map a ConfigurationDS0 Map B Configuration DS0 Map a Configuration 114 Status Messages Network Interface NI Alarm Messages Network Interface NI 116 Index Symbols DTE Qrss 120 Product Support Information