Chain-out Pinout | ADTRAN TSU 600 guide

Chapter 2. Installation

Chain-out

This is used to connect to another TSU 600 Chain-in connector. See Table 2-C for the pinout for the chain- out connector.

Connections

The chain-out connections are as follows:

	Connector type			RJ-48
	Part number			AMP# 555164-2
				Table 2-C
				Chain-out Pinout

	PIN	NAME		DESCRIPTION

	1	GND	Ground - connected to unit chassis.
	1	GND	Connected to GND of next unit (pin 1).
			Connected to GND of next unit (pin 1).

	2	UNUSED

	3	TX DATA	Data transmitted to chained units by the
	3	TX DATA	TSU 600. Connect to RX DATA of the next
			unit (chain in pin 3).

	4	UNUSED

	5	RX DATA	Data received from chained units by the
	5	RX DATA	TSU 600. Connect to TX DATA of the next
			unit (chain in pin 5).

	6,7,8	UNUSED

32

TSU 600 User Manual

61200.076L2-1

Image 44

ADTRAN TSU 600 user manual Chain-out Pinout

Contents

TSU Part Number 1200076L2 1200076L2#DC Table of Contents Service Type Table of Contents Table of Contents Installation Operation Table of Contents Example Operations Figures 15. Drop and Insert, Voice, and Bridging Application Set Up Tables T1 Service Offerings T1/FT1 Overview Fractional T1 Front View of the TSU TSU 600 OverviewFunctional Description Introduction Identification of Rear Panel Layout TSU 600 Rear Panel Features of the TSU TSU 600 Interfaces TSU InterfacesNetwork Interface Control Port Input Chain Port Output Three Methods of Control Front PanelAdtran PC Program Snmp Slots Option Slot ArrangementSlot TSU 600 Option Slot Arrangement Other Data Interfaces Option PortsSecondary Interfaces SI Network Timed Clock Source TSU 600 Clock SourcesNetwork Timed DTE Timed DTE Clock Source Internal Timing Internal Clock Source Normal CSU Timing Loopback Tests TSU 600 TestingSelf Tests TSU Network Loopback Tests DTE Interface Loopback Port Interface Loopback Pattern Generation TSU 600 Configuration Applications Bridge, PBX, Video Conferencing Application Set UpTSU 600 Option Modules Bridge, PBX, Video Conferencing Application All Voice Application Set Up All Voice Application Drop and Insert, Voice, and Bridging Application Variations of Mixed Applications Variations of Mixed Applications Provided by Customer UNPACK, INSPECT, Power ConnectionShipped by Adtran Power Connection Warranty and Customer Service Grounding Instructions UL Installation Network Pinout WiringNetwork Control In/Chain-in GND Chain-out Chain-out Pinout Power UP Testing and Initialization Self Test Set User Passcode To Establish a Passcode Set Unit Identification No Passcode Desired Set Control Port Control In PC Example of Chain-in Normal Power-Up Procedure Correct Passcode Operation Identification of Front Panel Layout TSU 600 Front Panel Layout TSU Alarm red Used in various menus to clear data/result fields General Menu Operation Select a Menu Item Sample Submenu Data Port Identification Display and Data Fields Module Slots, TSU Menu Structure Four Opening Menus Opening Menu Functions Display of Opening Menus Shows status of incoming commands on the chain-in port Displays and can be used to set the time and date Opening Menu Functions Detailed Discussion Status Complete Status Menu Network Interface Performance Report Network Performance Reports NI Perf Rpts1NI Perf Rpts Network Interface Errors NI Errors Active Alarms Network Interface Error Type View History Port Status Remote Port Configuration Config Complete Configuration Menu YEL Alarm Network NIFormat D4 is equivalent to superframe format SF Xmit PRM Clock SourceSET LBO Inband Lpbck Traps AccessCTL Port Auto Map Exchange Selection DisplayOFF Selection Times for Map Exchange DS0 Map Designations Copy a Temp Create Temp Create Temp Selection Screen Review MAP AB Edit Temp Selected Port and Quantity of DS0sReview Temp Apply Temp a Port Configuration Port Config Port Configuration Utility Util Complete Utility Menu Tree Time/Date Factory Restore Set Passcode Unit ID ID Software Revision Software Rev Port Utility Test Complete Test Menu Network Tests Remote Loopbck All zeros Qrss always runs at 64K/DS0 Bit error Than 1 bit error and less thanThan 320 bit errors Since the start of testing Run Selftest Cancel Tests Port Tests Operation Voice and Data MIX Example of Voice and Data Mix Steps to SET UP Voice and Data MIX Configure the NetworkConfiguration for Network Interface Prior to Step Select the number of DS0s/Port12 Configure DTE Port 1.1 Nx56/64 From Option ModuleConfiguration for DTE Port Nx56/64 Complete the DS0 Map ConfigurationConfiguration for DS0 Map Complete a Configuration Table for the DSX-1 PBX Passthru Activate Configuration MenuConfiguration for DSX-1 PBX Passthru First Two Configuration Menu Items Configuring the Network Interface First Two Network NI Configuration Menu Items First Two Network NI Menu Items Create Map Menu with Displayed DS0 Number Configuring the DS0 MAPDS0 Map a and Map B Configuration Menu Items Passthru Selection Field Display of DS0 Port Name Example Operations Review Screen Temporary MAPReview Edit Window Showing Edit Temp Option Window Showing the Error Screen Used To Change Mode Configuring the PortsWindow Showing Port Configuration Option Example Operations Testing Example Far End Looped Back Test Test Menu One 101 Four Test Submenu Windows Screen that Appears During Loopback Verification Test Pattern Screen for Qrss all DS0s Pressing the 2 key results in injecting errors SES Test Termination 106 Appendix a TSU 600 Complete Menu Tree Figure A-1 DTE Data Rate Chart DTE Data Rate vs. DS0s DTE RATE=56K DTE RATE=64K Appendix C System Configuration Charts Configure Network Configure DTE Port 1.1 Nx56/64 Configuration Chart for DTE PortRate Chart Select number of DS0s/PORT DS0 Map a Configuration DS0 Map B ConfigurationDS0 Map a Configuration DS0 Map B Configuration 114 Alarm Messages Network Interface NI Status Messages Network Interface NI 116 Symbols Index DTE Qrss 120 Product Support Information