Manuals / ADTRAN / Computer Equipment / Network Card

ADTRAN user manual TSU 600 Option Slot Arrangement

Models: TSU 600

1 133

Download 133 pages 17.65 Kb

Page 23

Chapter 1. Introduction

Slot 6

Slot 6 services any option module type including secondary network interface ports (DSX-1 (PBX) and Full D&I), but not the DTE timing source. If a second- ary network interface port is to be used, it must be installed in slot 6.

SLOT 1	SLOT 4	POWER
DTE TIMING		SUPPLY
DTE TIMING
SLOT 2	SLOT 5
DIAL BACKUP
SLOT 3	SLOT 6
	SECONDARY INTERFACE
	DSX-1; FULL D&I

Figure 1-4

TSU 600 Option Slot Arrangement

61200.076L2-1

TSU 600 User Manual

11

Image 23

ADTRAN user manual TSU 600 Option Slot Arrangement

Contents

Part Number 1200076L2 1200076L2#DC TSUTable of Contents Service Type Table of Contents Table of Contents Installation Operation Table of Contents Example Operations Figures 15. Drop and Insert, Voice, and Bridging Application Set Up Tables T1/FT1 Overview T1 Service OfferingsFractional T1 Front View of the TSU TSU 600 OverviewFunctional Description Introduction TSU 600 Rear Panel Identification of Rear Panel LayoutFeatures of the TSU TSU 600 Interfaces TSU InterfacesNetwork Interface Chain Port Output Control Port InputSnmp Three Methods of ControlFront Panel Adtran PC ProgramSlots Option Slot ArrangementSlot TSU 600 Option Slot Arrangement Other Data Interfaces Option PortsSecondary Interfaces SI Network Timed Clock Source TSU 600 Clock SourcesNetwork Timed DTE Clock Source DTE TimedInternal Clock Source Internal TimingNormal CSU Timing Loopback Tests TSU 600 TestingSelf Tests Network Loopback Tests TSUPort Interface Loopback DTE Interface LoopbackPattern Generation Bridge, PBX, Video Conferencing Application TSU 600 Configuration ApplicationsBridge, PBX, Video Conferencing Application Set Up TSU 600 Option ModulesAll Voice Application All Voice Application Set UpVariations of Mixed Applications Drop and Insert, Voice, and Bridging ApplicationVariations of Mixed Applications Provided by Customer UNPACK, INSPECT, Power ConnectionShipped by Adtran Power Connection Warranty and Customer Service Grounding Instructions UL Installation Network Pinout WiringNetwork GND Control In/Chain-inChain-out Pinout Chain-outSelf Test Power UP Testing and InitializationTo Establish a Passcode Set User PasscodeNo Passcode Desired Set Unit IdentificationControl In PC Set Control PortExample of Chain-in Correct Passcode Normal Power-Up ProcedureIdentification of Front Panel Layout OperationTSU TSU 600 Front Panel LayoutAlarm red Used in various menus to clear data/result fields Select a Menu Item General Menu OperationSample Submenu Display and Data Fields Data Port IdentificationModule Slots, TSU Four Opening Menus Menu StructureDisplay of Opening Menus Opening Menu FunctionsShows status of incoming commands on the chain-in port Displays and can be used to set the time and date Opening Menu Functions Detailed Discussion Complete Status Menu StatusNetwork Interface Performance Report Network Performance Reports NI Perf Rpts1NI Perf Rpts Network Interface Errors NI Errors Network Interface Error Type Active AlarmsPort Status View HistoryRemote Port Complete Configuration Menu Configuration ConfigD4 is equivalent to superframe format SF YEL AlarmNetwork NI FormatInband Lpbck Xmit PRMClock Source SET LBOTraps AccessCTL Port Auto Map Exchange Selection DisplayOFF Selection Times for Map Exchange DS0 Map Designations Create Temp Copy a TempReview MAP AB Create Temp Selection ScreenEdit Temp Selected Port and Quantity of DS0sReview Temp Apply Temp a Port Configuration Port Configuration Port ConfigComplete Utility Menu Tree Utility UtilTime/Date Factory Restore Set Passcode Unit ID ID Software Revision Software Rev Port Utility Complete Test Menu TestNetwork Tests Remote Loopbck Qrss always runs at 64K/DS0 All zerosSince the start of testing Bit errorThan 1 bit error and less than Than 320 bit errorsRun Selftest Port Tests Cancel TestsOperation Example of Voice and Data Mix Voice and Data MIXPrior to Step Steps to SET UP Voice and Data MIXConfigure the Network Configuration for Network InterfaceSelect the number of DS0s/Port12 Configure DTE Port 1.1 Nx56/64 From Option ModuleConfiguration for DTE Port Nx56/64 Complete the DS0 Map ConfigurationConfiguration for DS0 Map First Two Configuration Menu Items Complete a Configuration Table for the DSX-1 PBX PassthruActivate Configuration Menu Configuration for DSX-1 PBX PassthruFirst Two Network NI Configuration Menu Items Configuring the Network InterfaceFirst Two Network NI Menu Items Create Map Menu with Displayed DS0 Number Configuring the DS0 MAPDS0 Map a and Map B Configuration Menu Items Display of DS0 Port Name Passthru Selection FieldExample Operations Review Screen Temporary MAPReview Window Showing Edit Temp Option EditWindow Showing the Error Screen Used To Change Mode Configuring the PortsWindow Showing Port Configuration Option Example Operations Far End Looped Back Test Testing Example101 Test Menu OneFour Test Submenu Windows Test Pattern Screen for Qrss all DS0s Screen that Appears During Loopback VerificationSES Pressing the 2 key results in injecting errorsTest Termination 106 Appendix a Figure A-1 TSU 600 Complete Menu TreeDTE Data Rate Chart DTE RATE=56K DTE RATE=64K DTE Data Rate vs. DS0sConfigure Network Appendix C System Configuration ChartsSelect number of DS0s/PORT Configure DTE Port 1.1 Nx56/64Configuration Chart for DTE Port Rate ChartDS0 Map B Configuration DS0 Map a ConfigurationDS0 Map B Configuration DS0 Map a Configuration114 Status Messages Network Interface NI Alarm Messages Network Interface NI116 Index SymbolsDTE Qrss 120 Product Support Information