Manuals / ADTRAN / Computer Equipment / Network Card

ADTRAN TSU 600 user manual Appendix C System Configuration Charts, Configure Network

Models: TSU 600

1 133

Download 133 pages 17.65 Kb

Page 123

Appendix C. System Configuration Charts

Appendix C System Configuration Charts

This appendix contains five steps/tables to support the chapter, Example Operations. It is recommended that these tables be copied and used as work sheets when configuring the system.

Step 1: Configure Network

Table C-A Control Pin Connection Configuration Chart for Network Interface

MENU ITEM	SELECTION USED	SELECTIONS AVAILABLE

1)FORMAT		D4, ESF*

2)CODE		AMI, B8ZS*

3)YEL ALARM		ENABLE*, DISABLE

4)XMIT PRM		ON, OFF*

5)TIMING MODE		NETWK* (NI), INTERNAL, BASE DTE,
		SECONDARY INTERFACE, NORMAL

6)LINE BUILD		0dB*, 7.5dB, -15dB, -22.5dB, AUTO

7)INBAND LOOPBK		ACCEPT*, REJECT

8)BIT STUFFING		DISA*, ENA

*= Factory Default

61200.076L2-1

TSU 600 User Manual

111

Image 123

ADTRAN TSU 600 user manual Appendix C System Configuration Charts, Configure Network

Contents

Part Number 1200076L2 1200076L2#DC TSUTable of Contents Service Type Table of Contents Table of Contents Installation Operation Table of Contents Example Operations Figures 15. Drop and Insert, Voice, and Bridging Application Set Up Tables T1/FT1 Overview T1 Service OfferingsFractional T1 TSU 600 Overview Functional DescriptionFront View of the TSU Introduction TSU 600 Rear Panel Identification of Rear Panel LayoutFeatures of the TSU TSU Interfaces Network InterfaceTSU 600 Interfaces Chain Port Output Control Port InputSnmp Three Methods of ControlFront Panel Adtran PC ProgramOption Slot Arrangement SlotSlots TSU 600 Option Slot Arrangement Option Ports Secondary Interfaces SIOther Data Interfaces TSU 600 Clock Sources Network TimedNetwork Timed Clock Source DTE Clock Source DTE TimedInternal Clock Source Internal TimingNormal CSU Timing TSU 600 Testing Self TestsLoopback Tests Network Loopback Tests TSUPort Interface Loopback DTE Interface LoopbackPattern Generation Bridge, PBX, Video Conferencing Application TSU 600 Configuration ApplicationsBridge, PBX, Video Conferencing Application Set Up TSU 600 Option ModulesAll Voice Application All Voice Application Set UpVariations of Mixed Applications Drop and Insert, Voice, and Bridging ApplicationVariations of Mixed Applications UNPACK, INSPECT, Power Connection Shipped by AdtranProvided by Customer Power Connection Warranty and Customer Service Grounding Instructions UL Installation Wiring NetworkNetwork Pinout GND Control In/Chain-inChain-out Pinout Chain-outSelf Test Power UP Testing and InitializationTo Establish a Passcode Set User PasscodeNo Passcode Desired Set Unit IdentificationControl In PC Set Control PortExample of Chain-in Correct Passcode Normal Power-Up ProcedureIdentification of Front Panel Layout OperationTSU TSU 600 Front Panel LayoutAlarm red Used in various menus to clear data/result fields Select a Menu Item General Menu OperationSample Submenu Display and Data Fields Data Port IdentificationModule Slots, TSU Four Opening Menus Menu StructureDisplay of Opening Menus Opening Menu FunctionsShows status of incoming commands on the chain-in port Displays and can be used to set the time and date Opening Menu Functions Detailed Discussion Complete Status Menu StatusNetwork Performance Reports NI Perf Rpts 1NI Perf RptsNetwork Interface Performance Report Network Interface Errors NI Errors Network Interface Error Type Active AlarmsPort Status View HistoryRemote Port Complete Configuration Menu Configuration ConfigD4 is equivalent to superframe format SF YEL AlarmNetwork NI FormatInband Lpbck Xmit PRMClock Source SET LBOAccess CTL PortTraps Map Exchange Selection Display OFFAuto Selection Times for Map Exchange DS0 Map Designations Create Temp Copy a TempReview MAP AB Create Temp Selection ScreenSelected Port and Quantity of DS0s Review TempEdit Temp Apply Temp a Port Configuration Port Configuration Port ConfigComplete Utility Menu Tree Utility UtilTime/Date Factory Restore Set Passcode Unit ID ID Software Revision Software Rev Port Utility Complete Test Menu TestNetwork Tests Remote Loopbck Qrss always runs at 64K/DS0 All zerosSince the start of testing Bit errorThan 1 bit error and less than Than 320 bit errorsRun Selftest Port Tests Cancel TestsOperation Example of Voice and Data Mix Voice and Data MIXPrior to Step Steps to SET UP Voice and Data MIXConfigure the Network Configuration for Network InterfaceConfigure DTE Port 1.1 Nx56/64 From Option Module Configuration for DTE PortSelect the number of DS0s/Port12 Complete the DS0 Map Configuration Configuration for DS0 MapNx56/64 First Two Configuration Menu Items Complete a Configuration Table for the DSX-1 PBX PassthruActivate Configuration Menu Configuration for DSX-1 PBX PassthruFirst Two Network NI Configuration Menu Items Configuring the Network InterfaceFirst Two Network NI Menu Items Configuring the DS0 MAP DS0 Map a and Map B Configuration Menu ItemsCreate Map Menu with Displayed DS0 Number Display of DS0 Port Name Passthru Selection FieldExample Operations Temporary MAP ReviewReview Screen Window Showing Edit Temp Option EditWindow Showing the Error Configuring the Ports Window Showing Port Configuration OptionScreen Used To Change Mode Example Operations Far End Looped Back Test Testing Example101 Test Menu OneFour Test Submenu Windows Test Pattern Screen for Qrss all DS0s Screen that Appears During Loopback VerificationSES Pressing the 2 key results in injecting errorsTest Termination 106 Appendix a Figure A-1 TSU 600 Complete Menu TreeDTE Data Rate Chart DTE RATE=56K DTE RATE=64K DTE Data Rate vs. DS0sConfigure Network Appendix C System Configuration ChartsSelect number of DS0s/PORT Configure DTE Port 1.1 Nx56/64Configuration Chart for DTE Port Rate ChartDS0 Map B Configuration DS0 Map a ConfigurationDS0 Map B Configuration DS0 Map a Configuration114 Status Messages Network Interface NI Alarm Messages Network Interface NI116 Index SymbolsDTE Qrss 120 Product Support Information