Safety Considerations

Warnings and

Cautions

WARNING

This product is a Safety Class I instrument that is provided with a protective earth terminal when installed in the mainframe. The mainframe, AFG, and all related documentation should be reviewed for familiarization with safety markings and instructions before operation or service.

Refer to the WARNINGS page (page 4) in this manual for a summary of safety information. Safety information for preventive maintenance, testing, and service follows and is also found throughout this manual.

This section contains WARNINGS which must be followed for your protection and CAUTIONS which must be followed to avoid damage to the equipment when performing instrument maintenance or repair.

SERVICE-TRAINED PERSONNEL ONLY. The information in this manual is for service-trained personnel who are familiar with electronic circuitry and are aware of the hazards involved. To avoid personal injury or damage to the instrument, do not perform procedures in this manual or do any servicing unless you are qualified to do so.

CHECK MAINFRAME POWER SETTINGS. Before applying power, verify that the mainframe setting matches the line voltage and that the correct fuse is installed. An uninterruptible safety earth ground must be provided from the main power source to the supplied power cord set.

GROUNDING REQUIREMENTS. Interruption of the protective (grounding) conductor (inside or outside the mainframe) or disconnecting the protective earth terminal will cause a potential shock hazard that could result in personal injury. (Grounding one conductor of a two-conductor outlet is not sufficient protection.)

IMPAIRED PROTECTION. Whenever it is likely that instrument protection has been impaired, the mainframe must be made inoperative and be secured against any unintended operation.

REMOVE POWER IF POSSIBLE. Some procedures in this manual may be performed with power supplied to the mainframe while protective covers are removed. Energy available at many points may, if contacted, result in personal injury. (If maintenance can be performed without power applied, the power should be removed.)

10 General Information

Agilent E1445A Service Manual

Page 11 Page 13
Page 12
Image 12
Agilent Technologies 75000 Series C, E1445A service manual Safety Considerations
Page 11 Page 13

75000 Series C, E1445A specifications

The Agilent Technologies E1445A is part of the renowned 75000 Series C modular test and measurement instruments, specifically designed to provide high-performance capabilities for advanced electronic testing applications. This versatile and compact device is essential for engineers and technicians who require reliable and accurate measurement solutions in research and development, manufacturing, and quality assurance environments.

One of the main features of the E1445A is its modular architecture, which allows for a high degree of customization and scalability. Users can integrate the E1445A with other modules within the 75000 Series C, facilitating a wide range of testing scenarios from basic measurements to complex multi-channel applications. This modularity not only maximizes resource utilization but also simplifies maintenance and upgrades, ensuring longevity and adaptability in rapidly evolving technological landscapes.

The E1445A is equipped with advanced measurement technologies that enhance its performance. It offers precision analog and digital measurement capabilities, which are essential for a diverse array of applications, including semiconductor testing, circuit debugging, and signal integrity analysis. With its highly accurate time and frequency measurements, the E1445A stands out in applications that demand meticulous timing and synchronization.

The device also features a high-speed data acquisition system, enabling users to capture and analyze signals at faster rates. This is complemented by sophisticated signal processing algorithms that improve noise immunity and measurement reliability, making it suitable even for challenging environments. Furthermore, the E1445A supports various communication interfaces, which facilitate seamless connectivity with modern computer systems and data analysis software.

Another characteristic of the E1445A is its user-friendly interface, which simplifies operation and minimizes the learning curve for new users. The intuitive controls and graphical display make it easier for users to navigate through various measurement setups and results. Additionally, the device comes with extensive documentation and support resources, allowing users to maximize their efficiency and effectiveness in test execution.

In summary, the Agilent Technologies E1445A from the 75000 Series C is a robust and flexible test and measurement solution. Its modularity, advanced measurement technologies, high-speed capabilities, and user-friendly interface make it a valuable tool for professionals in electronics testing and validation. Its ability to adapt to a wide range of applications positions it as a critical asset in today's fast-paced technological environment.
Top Page Image Contents