Appendix | 163 | ||||
|
|
|
|
|
|
|
|
| Tools Required For Installation |
| |
| Check | Qty | Item | USED ON | |
|
|
| All Maintenance Tools |
|
|
|
| 1 | Installation Manual | general |
|
|
| 1 | Electrical drawings | wiring |
|
|
| 1 | Computer and program | PLC control |
|
|
| 1 | Tower Directions | tower assembly |
|
|
| 1 | Template | tower assembly |
|
|
| 1 | tip brake cables |
| |
|
| 1 | 15/16 combination wrench | 5/8” blade bolts |
|
|
| 2 | 15/16 socket | 5/8” blade bolts |
|
|
| 2 | ½drive socket wrench | 5/8” blade bolts |
|
|
| 1 | 250 | 5/8” blade bolts (120, 180 |
|
|
| 6 | 1” | temporary tower fastener |
|
|
| 1 | Crow bar | tower top aligning |
|
|
| 1 | 36" drift pin | tower top aligning |
|
|
| 2 | 1" Drift Pin | tower top aligning |
|
|
| 1 | 1 ½socket, 3/4 drive | 1’’ tower top bolts |
|
|
| 1 | 1 ½combination wrench | 1’’ tower top bolts |
|
|
| 1 | 1 7/16 socket | 1’’ tower top bolts |
|
|
| 1 | 600 lb torque wrench, ¾drive | 1” tower top bolts (600 |
|
|
| 1 | 1/2 to 3/4 drive adaptor | general |
|
|
| 1 | ¾drive socket wrench | 1” tower top bolts |
|
|
| 1 | Level | leveling tower |
|
|
| 1 | 2 3/8 open ended wrench | 1 1/2 tower base bolts |
|
|
| 1 | 1 1/16 socket, 3/4" drive | 5/8” brace bolts |
|
|
| 1 | 1 1/16 socket, 1/2" drive | 5/8” brace bolts |
|
|
| 1 | 1 1/16 combination wrench | 5/8” brace bolts |
|
|
| 1 | 15/16 combination wrench | 5/8” brace pal nuts |
|
|
| 1 | 1 5/8 socket | 1” flange bolt |
|
|
| 1 | 1 5/8 combination wrench | 1” flange pal nuts |
|
|
| 2 + | Lifting straps | tower assembly, blade assembly |
|
|
| 2 | Ropes, 100 ft. | maneuver turbine when raising |
|
|
| 1 | Loctite 271 | blade bolts |
|
|
| 1 | 7/8" socket, 1/2" drive | safety cable big |
|
|
| 1 | 3/4" socket, 1/2" drive | safety cable small |
|
|
| 1 | 13/16" combination | safety cable pal nut |
|
|
| 1 | 5/16 Allen wrench | generator jct box ground lug |
|
|
| 1 | 3/16 Allen wrench | generator jct box connector lug |
|
|
| 1 | Rotating File | removing blade epoxy |
|
|
| 1 | Grinder bit and extension | removing blade epoxy |
|
|
| 1 | wire clippers | anemometer zip ties |
|
|
| 1 | 9/16" combination wrench | anemometer bolt |
|
|
| 1 | Rubber insulation tape | general |
|
|
| 1 | Wire Cutters (large wire) | power wiring | |
NOTICE: Use of the material contained in this document is subject to the warning on page Iv and the disclaimer on page v of this document.
DOC012R02 | AOC 15/50 User Manual | Nov 2001 |
