Manuals / Cabletron Systems / Computer Equipment / Network Hardware

Cabletron Systems manual Mmac and CSMIM-T1are trademarks of Cabletron Systems, Inc

Models: CSMIM-T1

1 198

Download 198 pages 40.85 Kb

Page 3

NOTICE

Cabletron Systems reserves the right to make changes in speciﬁcations and other information contained in this document without prior notice. The reader should in all cases consult Cabletron Systems to determine whether any such changes have been made.

The hardware, ﬁrmware, or software described in this manual is subject to change without notice.

IN NO EVENT SHALL CABLETRON SYSTEMS BE LIABLE FOR ANY INCIDENTAL, INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES WHATSOEVER (INCLUDING BUT NOT LIMITED TO LOST PROFITS) ARISING OUT OF OR RELATED TO THIS MANUAL OR THE INFORMATION CONTAINED IN IT, EVEN IF CABLETRON SYSTEMS HAS BEEN ADVISED OF, KNOWN, OR SHOULD HAVE KNOWN, THE POSSIBILITY OF SUCH DAMAGES.

© Copyright April 1997 by:

Cabletron Systems, Inc.

P.O. Box 5005

Rochester, NH 03866-5005

All Rights Reserved

Printed in the United States of America

Order number: 9032222 April 1997

MMAC and CSMIM-T1are trademarks of Cabletron Systems, Inc.

Annex, Annex Three, Annex3, Remote Annex 6000 and Remote Annex 6100 are trademarks of Xylogics, Inc.

Portions subject to copyright by Microcom Systems, Inc. 1993-1995. Used by permission.

All other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies.

iii

Image 3

Cabletron Systems manual Mmac and CSMIM-T1are trademarks of Cabletron Systems, Inc

Contents

CSMIM-T1 Hardware Installation Guide Page Mmac and CSMIM-T1are trademarks of Cabletron Systems, Inc FCC Notice REN/SOC FIC Usoc CSMIM-T1 Industry Canada Certiﬁcation Number Equipment Attachment LimitationsExclusion of Warranty Disclaimer of Liability Viii CSMIM-T1 Hardware Installation Guide Table of Contents Table of Contents Chapter Modem Guide Xii CSMIM-T1 Hardware Installation Guide Organization of this Document GeneralFollowing conventions are used throughout this document Document ConventionsCtron.com LoginPassword Getting HelpCSMIM-T1 Overview CSMIM-T1 Front Panel Software InformationCSMIM-T1 Console PortSystem LED Indicators SET UP SwitchThere are 7 indicators to show system activity and status Network Status / Alarms 4 T-1 Network AccessModem Port Status LEDs Modem Conﬁguration Status LEDsTelco Connection Information Connecting the CSMIM-T1 to a Full T-1 LineEFS Key Number ConnectivityTelco Connection Information Connecting the CSMIM-T1 to a Fractional T-1 LineCompatibility CSMIM-T1 Physical / Statistical InformationHeight 11.5 in .4 cm Width Depth Electromagnetic Compatability SafetyOperating Non-operatingCSMIM-T1 Hardware Installation Guide Chapter Installing the CSMIM-T1 Locating the Ethernet Jumpers Ethernet Jumper SettingsSetting the Subnet Jumper Setting the Ethernet JumpersNetwork Bypass Jumper Network Bypass JumperInstall the CSMIM-T1 into the MMAC-FNB backplane as follows Installing the CSMIM-T1Mmac M8FNB Connecting a Console Terminal Making ConnectionsLine Speed Cable Length Feet Allowed Loss Connecting a T1 Network Interface POWER-UP and Test Connecting a Drop/Insert InterfaceREVISION/CONFIGURATION Information AUTO-INITIALIZING the Roms Bootp Rarp Software Installation ProceduresExecute the boot command see the boot command in Chapter Invoking the Console Monitor Self-Booting the CSMIM-T1Reloading EFS Key Value Chapter ROM Monitor Commands ROM Monitor Commands Commands AddrAddr -d Addr -dcommand display looks like this Addr command display looks like thisBoot -lv ﬁlename BootCSMIM-T1 Hardware Installation Guide Monitor boot CSMIM-T1 Hardware Installation Guide Boot -lcommand display looks like this EOF Config Config command display looks like this3 conﬁg Command display looks like this Console-baudConsole-baud Erase EraseHelp ImageImage -d ﬁlename Ipx -d Image -dcommand display looks like thisIpx command display looks like this 8 ipxLatkey Command syntax isLatkey command display looks like this Latkey -dcommand displays the current LAT key settingNet 10 mop11 net Mop -dPing Optionkey command display looks like thisOptionkey -dcommand displays the current settings OptionkeyWhen invoked, the command displays a menu of options PortsPorts -d CSMIM-T1 Hardware Installation Guide Sequence -d interface,interface SequenceSlip -d port SlipSlip Command Prompts CSMIM-T1 Hardware Installation Guide Stats command display looks like this StatsStats -slip StatisticDescription Command Command Type Description T-1 CommandsStats -T current total all intervalset clearalarm Stats -T current command display looks like thisArgument Description Frame synchronization. During this condition, the T-1 Field DescriptionDrop/Insert Interface is out of frame sync or not receiving Reset t1 soft hard esf Keyword Deﬁnition Describes the arguments for T1loopback Keyword Description T-1 ParametersCSMIM-T1 software comes with the following new parameters Parameter DescriptionsOption Description Sigproto Tniclock SET T-1 Parameters Example Ds0=2 loopstart Ds0=11 CSMIM-T1 Hardware Installation Guide Chapter Troubleshooting Procedures Status LEDs DescriptionGeneral Normal Mode CSMIM-T1 Diagnostics POWER-UP and Boot ProceduresNormal Mode Error-Free Sequence ActivityAmber Normal Mode Error Sequence Setup Mode Error-Free Sequence SET UP ModeSetup Mode Error States Boot Failures Boot Error Report Errors CSMIM-T1 sensed a hardware error during message Error DescriptionSee Table ErrorDescriptionCorrecting CSMIM-T1 Parameters Unix Host on the LAN Load Server Host Not RespondingAnother CSMIM-T1 VAX VMS Load Host on the LAN Activity Green Amber CSMIM-T1 DumpsNetwork SystemAddress Filename Pathname Chapter Modem Guide Features Using the AT Command SET Title Default Key AT Command Factory DefaultsEstablishing 11-Bit Data Connections 3 V.32bis Cellular Connections Using AT Commands Universal Cellular SetupMNP 10 V.32bis Quick Connect Cellular Only Setup Modulation Protocols V.32bis Protocols Bell 212A protocol is for 1200 bps full-duplex connections Protocol Issue %G0 Issue %G1 Protocol Conﬁguration Command SettingsSpeed and Protocol Connection Matrices Modem Speed and Protocol Combinations For operations at V.22 600 bps, both modems must be set to Error Correction Error Correction Diagnostics Power-Up DiagnosticsLocal Analog Loopback with Self-Test Remote Digital Loopback with Self-Test Local Analog LoopbackLocal Digital Loopback Remote Digital LoopbackAutomatically Terminating a Test Register S18 Respond to Remote Digital LoopbackResult Codes Connection Result Code TablesShort Form Long Form ATV1-M0W0 or ATV1-M0W1 Report DTE Speed Result CodesReport Modulation Speed ATV1-M0W2ATV0W0 or ATV0W1 Report DTE speed ATV0W2 Report Modulation Speed Entering Commands Command SETIssuing AT Commands at any Speed Repeat Last CommandAnswer Bn ITU-T/Bell Mode An Auto-Reliable Fallback Character\An Maximum MNP Block Size Bn Modem-Port Bps Rate \Bn Transmit BreakCompression Control @Cn CTS, DSR, and DCD Connect Message Control Cn Serial-Port DCD Control\C0 \Cn Auto-Reliable BufferDial modifiers allow you to add conditions to the telephone H2 commandATD 011225551234 Enter Dial ModifiersATD 9,,5551234 Enter Operating Mode Dial Modiﬁers This bong signal. Once it detects it, the modem continuesFirst, the modem hangs up and displays no Prompt Tone Dn Disconnect Buffer Delay DL Redial the Last Telephone Number DialedRedials the last telephone number that the modem dialed \D0 DTR ControlRepeat Dial \Dn Serial-Port DSR/CTS ControlDCD ResultCommand Echo En Auto-RetrainEnModem-Port Data Length Mode En Compromise Equalizer\En Data Echo \E0Guard Tone Restore Factory DefaultsSecondary Flow Control Independent Serial-Port/Modem-Port Speed\Gn Modem-Port Flow Control \G0Hang Up Identification Detect Phase\Jn Bps Rate Adjust Link Negotiation Speed\Kn Break Control KnMNP Extended Services2illustrates the \Kn command Provides partial speed matching Enables speed matchingDisables speed matching Speed MatchingMode Setting on Originating Modem Bell212A Bell103 Modem Mode Mode Setting Answer Modem OriginatingPossible Connection Speed bps Modulation SelectionAllows connections through V.32bis Allows connections through V.FCMnMNP Class Connect Messages Mn Power Level Adjustment For Cellular Telephone Connections\N n Operating Mode Sets auto-reliable mode\N3 CSMIM-T1 Hardware Installation Guide On Enter Connect State On V.23 Equalizer Control OnSerial-Port ParityAT-O4D12345 Enter PnCheck Parity Pulse Dial\Q3 QuietFallback Modulation Speeds \Qn Serial-Port Flow ControlYour computer to resume transmitting data to the modem During direct mode connections, the modem does not use flowControl and ignores the \Q setting Modem continues to send out the characters and emptySn DSR Options Sn? Read Configuration RegistersRead All Registers RTS/CTS OptionsTn Test and Diagnostics Commands Read Online StatusTone Dial Clear Serial-Port Speed \Tn Inactivity Timer\Vn Error Correction Result Code Form Vn Result Code FormDisplay Modem Firmware Version Connection Speed Reporting Display Bootstrap RevisionWn Pulse Digit Command Wn Store Current ConfigurationWn Store Complete Configuration Xn Extended Result Codes \Xn XON/XOFF Pass-Through \X0Yn Long Space Disconnect Zn Reset Yn Designate Default User ProfileCommands to Change or Read Registers Displays the contents of all T n= n commands in decimalRegisters S3=n Carriage Return Character Range 0 255, Ascii decimal Default 43 +S1=n Ring Counter S2=n Escape Code CharacterS7=n Wait for Carrier After Dial S4=n Line Feed CharacterS5=n Backspace Character S6=n Wait Before DialingS8=n Pause Time for Dial Delay S10=n Delay for Hang Up After Carrier LossS9=n Carrier Detect Response Time S11=n Dtmf Tone Dialing Speed S12=n Escape Code Guard TimeS14=n Bit Mapped Register Bit Function Decimal Value Position S16=n Bit Mapped Register, Test OptionsS18=n Test Timer S22=n Bit Mapped Register Table S21=n Bit Mapped Register TableS23=n Bit Mapped Register Table S27=n Bit Mapped Register Table S25=n Delay to DTR and Asynchronous Time DelayT3=n Timer for V.21 and V.23 Answer Tone Duration T2=n Timer for V.21 Mode During Multi-Protocol AnswerT4=n Timer for Line Turnaround Delay Carrier On T5=n Timer for V.23 Half-Duplex Intercharacter DelayT6=n Timer for DCD Turn On Delay T7=n Timer for False Answer Abort T9=n Primary XON Flow Control CharacterT10=n Primary Xoff Flow Control Character T15=n V.24 Control Register T14=n Connect Message Delay TimerT11=n Secondary XON Flow Control Character T12=n Secondary Xoff Flow Control CharacterT16=n CTS Turn On Delay Timer T17=n V.32/V.32bis Connection Training TimerBit Function Position T22=n DSR Timer T19=n Bit Mapped RegisterT23=n Bit Mapped Register Table T42=n V.34/V.FC Connection Speed Selection T26=n Bit Mapped Register TableCSMIM-T1 Hardware Installation Guide Console Port Appendix a Port PIN/SIGNAL AllocationsInterface Ports DCE Cabletron part number 9372075 for DB25 male Additional Cabletron Cables and ConnectorsCSMIM-T1 Hardware Installation Guide Numerics SymbolsINDEX-2 INDEX-3 INDEX-4 INDEX-5 INDEX-6 INDEX-7 INDEX-8 INDEX-9 INDEX-10