Manuals / Cabletron Systems / Computer Equipment / Network Hardware

Cabletron Systems CSMIM-T1 manual Normal Mode Error Sequence

Models: CSMIM-T1

1 198

Download 198 pages 40.85 Kb

Page 90

Chapter 5: Troubleshooting Procedures

5.2.1.2Normal Mode Error Sequence

Table 5-3shows the state of the indicators when an error occurs at various stages of the start-up process. If the CSMIM-T1 fails during the hardware-test state (N2), the error condition is hardware failure NE2. A description of possible causes and solutions for each error condition is in the following paragraphs.

Table 5-3 Normal Mode Error LED States

	STAT	ATTN	TRAF
Activity	Green	Amber	Green

NE2: Hardware Failure	◆	◆	✕
NE5: Booted wrong image	●	◆	●

Key:

●On continuously.

✕Off.

■Flashing irregularly.

◆Flashing regularly (about 1Hz).

Activity NE2: Hardware Failure

The ROM diagnostics detected a CSMIM-T1 hardware problem requiring service. Call Technical Support.

Activity NE5: Booted Wrong Image

The CSMIM-T1 loaded the wrong image. Press the SET UP button for 3 seconds to reset the device. Following is a list of ways to prevent this problem in the future:

•Be sure that you conﬁgure the CSMIM-T1 with the appropriate image.

•Be sure that the image you are booting has the right name. Don’t rename the image ﬁle unless you are making a copy for safe keeping.

•If you used an na, admin, or cli boot command, specify the correct image and a valid ﬁlename.

5-6	CSMIM-T1 Hardware Installation Guide

Image 90

Cabletron Systems CSMIM-T1 manual Normal Mode Error Sequence

Contents

CSMIM-T1 Hardware Installation Guide Page Mmac and CSMIM-T1are trademarks of Cabletron Systems, Inc FCC Notice REN/SOC FIC Usoc CSMIM-T1 Equipment Attachment Limitations Industry Canada Certiﬁcation NumberExclusion of Warranty Disclaimer of Liability Viii CSMIM-T1 Hardware Installation Guide Table of Contents Table of Contents Chapter Modem Guide Xii CSMIM-T1 Hardware Installation Guide General Organization of this DocumentDocument Conventions Following conventions are used throughout this documentGetting Help LoginPassword Ctron.comCSMIM-T1 Overview Software Information CSMIM-T1 Front PanelConsole Port CSMIM-T1System LED Indicators SET UP SwitchThere are 7 indicators to show system activity and status 4 T-1 Network Access Network Status / AlarmsModem Conﬁguration Status LEDs Modem Port Status LEDsConnectivity Connecting the CSMIM-T1 to a Full T-1 LineEFS Key Number Telco Connection InformationConnecting the CSMIM-T1 to a Fractional T-1 Line Telco Connection InformationCompatibility CSMIM-T1 Physical / Statistical InformationHeight 11.5 in .4 cm Width Depth Non-operating SafetyOperating Electromagnetic CompatabilityCSMIM-T1 Hardware Installation Guide Chapter Installing the CSMIM-T1 Ethernet Jumper Settings Locating the Ethernet JumpersSetting the Ethernet Jumpers Setting the Subnet JumperNetwork Bypass Jumper Network Bypass JumperInstalling the CSMIM-T1 Install the CSMIM-T1 into the MMAC-FNB backplane as followsMmac M8FNB Connecting a Console Terminal Making ConnectionsLine Speed Cable Length Feet Allowed Loss Connecting a T1 Network Interface Connecting a Drop/Insert Interface POWER-UP and TestREVISION/CONFIGURATION Information AUTO-INITIALIZING the Roms Bootp Software Installation Procedures RarpExecute the boot command see the boot command in Chapter Self-Booting the CSMIM-T1 Invoking the Console MonitorReloading EFS Key Value Chapter ROM Monitor Commands ROM Monitor Commands Commands AddrAddr -d Addr command display looks like this Addr -dcommand display looks like thisBoot Boot -lv ﬁlenameCSMIM-T1 Hardware Installation Guide Monitor boot CSMIM-T1 Hardware Installation Guide Boot -lcommand display looks like this EOF Config Config command display looks like this3 conﬁg Command display looks like this Console-baudConsole-baud Erase EraseHelp ImageImage -d ﬁlename 8 ipx Image -dcommand display looks like thisIpx command display looks like this Ipx -dLatkey -dcommand displays the current LAT key setting Command syntax isLatkey command display looks like this LatkeyMop -d 10 mop11 net NetOptionkey Optionkey command display looks like thisOptionkey -dcommand displays the current settings PingWhen invoked, the command displays a menu of options PortsPorts -d CSMIM-T1 Hardware Installation Guide Sequence Sequence -d interface,interfaceSlip Slip -d portSlip Command Prompts CSMIM-T1 Hardware Installation Guide Stats command display looks like this StatsStats -slip StatisticDescription T-1 Commands Command Command Type DescriptionStats -T current total all intervalset clearalarm Stats -T current command display looks like thisArgument Description Field Description Frame synchronization. During this condition, the T-1Drop/Insert Interface is out of frame sync or not receiving Reset t1 soft hard esf Keyword Deﬁnition Describes the arguments for T1loopback T-1 Parameters Keyword DescriptionParameter Descriptions CSMIM-T1 software comes with the following new parametersOption Description Sigproto Tniclock SET T-1 Parameters Example Ds0=2 loopstart Ds0=11 CSMIM-T1 Hardware Installation Guide Chapter Troubleshooting Procedures LEDs Description StatusGeneral POWER-UP and Boot Procedures Normal Mode CSMIM-T1 DiagnosticsNormal Mode Error-Free Sequence ActivityAmber Normal Mode Error Sequence SET UP Mode Setup Mode Error-Free SequenceSetup Mode Error States Boot Failures Boot Error Report Error Description Errors CSMIM-T1 sensed a hardware error during messageErrorDescription See TableCorrecting CSMIM-T1 Parameters Load Server Host Not Responding Unix Host on the LANAnother CSMIM-T1 VAX VMS Load Host on the LAN CSMIM-T1 Dumps Activity Green AmberNetwork SystemAddress Filename Pathname Chapter Modem Guide Features Using the AT Command SET Key AT Command Factory Defaults Title DefaultEstablishing 11-Bit Data Connections 3 V.32bis Cellular Connections Using AT Commands Universal Cellular SetupMNP 10 V.32bis Quick Connect Cellular Only Setup Modulation Protocols V.32bis Protocols Bell 212A protocol is for 1200 bps full-duplex connections Protocol Conﬁguration Command Settings Protocol Issue %G0 Issue %G1Speed and Protocol Connection Matrices Modem Speed and Protocol Combinations For operations at V.22 600 bps, both modems must be set to Error Correction Error Correction Diagnostics Power-Up DiagnosticsLocal Analog Loopback with Self-Test Local Analog Loopback Remote Digital Loopback with Self-TestRemote Digital Loopback Local Digital LoopbackRespond to Remote Digital Loopback Automatically Terminating a Test Register S18Result Codes Connection Result Code TablesShort Form Long Form Result Codes ATV1-M0W0 or ATV1-M0W1 Report DTE SpeedATV1-M0W2 Report Modulation SpeedATV0W0 or ATV0W1 Report DTE speed ATV0W2 Report Modulation Speed Command SET Entering CommandsIssuing AT Commands at any Speed Repeat Last CommandAnswer Bn ITU-T/Bell Mode An Auto-Reliable Fallback Character\An Maximum MNP Block Size Bn Modem-Port Bps Rate \Bn Transmit BreakCompression Control Cn Serial-Port DCD Control @Cn CTS, DSR, and DCD Connect Message Control\Cn Auto-Reliable Buffer \C0Dial Modifiers H2 commandATD 011225551234 Enter Dial modifiers allow you to add conditions to the telephoneATD 9,,5551234 Enter Operating Mode Dial Modiﬁers This bong signal. Once it detects it, the modem continuesFirst, the modem hangs up and displays no Prompt Tone Dn Disconnect Buffer Delay DL Redial the Last Telephone Number DialedRedials the last telephone number that the modem dialed \Dn Serial-Port DSR/CTS Control DTR ControlRepeat Dial \D0Result DCDCommand Echo En Auto-RetrainEnModem-Port Data Length \E0 En Compromise Equalizer\En Data Echo ModeIndependent Serial-Port/Modem-Port Speed Restore Factory DefaultsSecondary Flow Control Guard Tone\Gn Modem-Port Flow Control \G0Hang Up Link Negotiation Speed Detect Phase\Jn Bps Rate Adjust IdentificationKnMNP Extended Services \Kn Break Control2illustrates the \Kn command Speed Matching Enables speed matchingDisables speed matching Provides partial speed matchingMode Setting on Originating Modem Bell212A Bell103 Mode Mode Setting Answer Modem Originating ModemAllows connections through V.FC Modulation SelectionAllows connections through V.32bis Possible Connection Speed bpsMn Power Level Adjustment For Cellular Telephone Connections MnMNP Class Connect Messages\N n Operating Mode Sets auto-reliable mode\N3 CSMIM-T1 Hardware Installation Guide On Enter Connect State On V.23 Equalizer Control OnSerial-Port ParityAT-O4D12345 Enter Pulse Dial PnCheck Parity\Qn Serial-Port Flow Control QuietFallback Modulation Speeds \Q3Modem continues to send out the characters and empty During direct mode connections, the modem does not use flowControl and ignores the \Q setting Your computer to resume transmitting data to the modemRTS/CTS Options Sn? Read Configuration RegistersRead All Registers Sn DSR OptionsTn Test and Diagnostics Commands Read Online StatusTone Dial \Tn Inactivity Timer Clear Serial-Port Speed\Vn Error Correction Result Code Form Vn Result Code FormDisplay Modem Firmware Version Display Bootstrap Revision Connection Speed ReportingWn Pulse Digit Command Wn Store Current ConfigurationWn Store Complete Configuration Xn Extended Result Codes \Xn XON/XOFF Pass-Through \X0Yn Long Space Disconnect Yn Designate Default User Profile Zn ResetCommands to Change or Read Registers Displays the contents of all T n= n commands in decimalRegisters S2=n Escape Code Character Range 0 255, Ascii decimal Default 43 +S1=n Ring Counter S3=n Carriage Return CharacterS6=n Wait Before Dialing S4=n Line Feed CharacterS5=n Backspace Character S7=n Wait for Carrier After DialS8=n Pause Time for Dial Delay S10=n Delay for Hang Up After Carrier LossS9=n Carrier Detect Response Time S11=n Dtmf Tone Dialing Speed S12=n Escape Code Guard TimeS14=n Bit Mapped Register S16=n Bit Mapped Register, Test Options Bit Function Decimal Value PositionS18=n Test Timer S21=n Bit Mapped Register Table S22=n Bit Mapped Register TableS23=n Bit Mapped Register Table S25=n Delay to DTR and Asynchronous Time Delay S27=n Bit Mapped Register TableT2=n Timer for V.21 Mode During Multi-Protocol Answer T3=n Timer for V.21 and V.23 Answer Tone DurationT4=n Timer for Line Turnaround Delay Carrier On T5=n Timer for V.23 Half-Duplex Intercharacter DelayT6=n Timer for DCD Turn On Delay T7=n Timer for False Answer Abort T9=n Primary XON Flow Control CharacterT10=n Primary Xoff Flow Control Character T12=n Secondary Xoff Flow Control Character T14=n Connect Message Delay TimerT11=n Secondary XON Flow Control Character T15=n V.24 Control RegisterT16=n CTS Turn On Delay Timer T17=n V.32/V.32bis Connection Training TimerBit Function Position T22=n DSR Timer T19=n Bit Mapped RegisterT23=n Bit Mapped Register Table T26=n Bit Mapped Register Table T42=n V.34/V.FC Connection Speed SelectionCSMIM-T1 Hardware Installation Guide Appendix a Port PIN/SIGNAL Allocations Console PortInterface Ports Additional Cabletron Cables and Connectors DCE Cabletron part number 9372075 for DB25 maleCSMIM-T1 Hardware Installation Guide Symbols NumericsINDEX-2 INDEX-3 INDEX-4 INDEX-5 INDEX-6 INDEX-7 INDEX-8 INDEX-9 INDEX-10