Another CSMIM-T1 | Cabletron Systems guide

BOOT Failures

When the CSMIM-T1 boots in test mode, the console displays the load server host’s Internet address, and indicates whether it receives a response to its Open File Request and to any of its Read File Requests. The host’s progress report indicates receipt of any File Server Requests and its responses to such requests. The host displays erpc_return 0 if it successfully receives a request and is sending out an afﬁrmative response. If any CSMIM-T1-related ﬁles are missing or cannot be installed, contact technical support (see Getting Help section in Preface).

A PC host running the UNIX operating system has the erpcd daemon (provided with the distribution and installed in /usr/annex) running in the background on the PC. Set the CSMIM-T1 and the erpcd on the load host into test mode:

1.For erpcd on the load server host, as superuser, kill the erpcd program and restart it using the –D option:

#/usr/annex/erpcd -D5

2.On the CSMIM-T1, hold down the SET UP button for 3 seconds to enter the SET UP mode. Then enter:

monitor:: boot -v

5.3.2.3Another CSMIM-T1

When troubleshooting a CSMIM-T1 conﬁgured as a load server host:

1.Use the CLI telnet command to access the unit and verify that it is up and running.

2.Communicate with the unit on the Ethernet using the superuser CLI ping command.

3.Verify the unit’s configuration using na.

The Annex Network Administrator’s Guide provides more information on these commands.

A CSMIM-T1 that has been reconﬁgured as a load server host, but not rebooted, cannot boot another CSMIM-T1 on the network. Rebooting the CSMIM-T1 load server host ensures that the parameters are set.

CSMIM-T1 Hardware Installation Guide

5-15

Image 99

Cabletron Systems manual Another CSMIM-T1

Contents

CSMIM-T1 Hardware Installation Guide Page Mmac and CSMIM-T1are trademarks of Cabletron Systems, Inc FCC Notice REN/SOC FIC Usoc CSMIM-T1 Industry Canada Certiﬁcation Number Equipment Attachment Limitations Exclusion of Warranty Disclaimer of Liability Viii CSMIM-T1 Hardware Installation Guide Table of Contents Table of Contents Chapter Modem Guide Xii CSMIM-T1 Hardware Installation Guide Organization of this Document General Following conventions are used throughout this document Document Conventions Ctron.com LoginPassword Getting Help CSMIM-T1 Overview CSMIM-T1 Front Panel Software Information CSMIM-T1 Console Port System LED Indicators SET UP SwitchThere are 7 indicators to show system activity and status Network Status / Alarms 4 T-1 Network Access Modem Port Status LEDs Modem Conﬁguration Status LEDs Telco Connection Information Connecting the CSMIM-T1 to a Full T-1 LineEFS Key Number Connectivity Telco Connection Information Connecting the CSMIM-T1 to a Fractional T-1 Line Compatibility CSMIM-T1 Physical / Statistical InformationHeight 11.5 in .4 cm Width Depth Electromagnetic Compatability SafetyOperating Non-operating CSMIM-T1 Hardware Installation Guide Chapter Installing the CSMIM-T1 Locating the Ethernet Jumpers Ethernet Jumper Settings Setting the Subnet Jumper Setting the Ethernet Jumpers Network Bypass Jumper Network Bypass Jumper Install the CSMIM-T1 into the MMAC-FNB backplane as follows Installing the CSMIM-T1 Mmac M8FNB Connecting a Console Terminal Making ConnectionsLine Speed Cable Length Feet Allowed Loss Connecting a T1 Network Interface POWER-UP and Test Connecting a Drop/Insert Interface REVISION/CONFIGURATION Information AUTO-INITIALIZING the Roms Bootp Rarp Software Installation Procedures Execute the boot command see the boot command in Chapter Invoking the Console Monitor Self-Booting the CSMIM-T1 Reloading EFS Key Value Chapter ROM Monitor Commands ROM Monitor Commands Commands AddrAddr -d Addr -dcommand display looks like this Addr command display looks like this Boot -lv ﬁlename Boot CSMIM-T1 Hardware Installation Guide Monitor boot CSMIM-T1 Hardware Installation Guide Boot -lcommand display looks like this EOF Config Config command display looks like this3 conﬁg Command display looks like this Console-baudConsole-baud Erase Erase Help ImageImage -d ﬁlename Ipx -d Image -dcommand display looks like thisIpx command display looks like this 8 ipx Latkey Command syntax isLatkey command display looks like this Latkey -dcommand displays the current LAT key setting Net 10 mop11 net Mop -d Ping Optionkey command display looks like thisOptionkey -dcommand displays the current settings Optionkey When invoked, the command displays a menu of options PortsPorts -d CSMIM-T1 Hardware Installation Guide Sequence -d interface,interface Sequence Slip -d port Slip Slip Command Prompts CSMIM-T1 Hardware Installation Guide Stats command display looks like this StatsStats -slip StatisticDescription Command Command Type Description T-1 Commands Stats -T current total all intervalset clearalarm Stats -T current command display looks like thisArgument Description Frame synchronization. During this condition, the T-1 Field Description Drop/Insert Interface is out of frame sync or not receiving Reset t1 soft hard esf Keyword Deﬁnition Describes the arguments for T1loopback Keyword Description T-1 Parameters CSMIM-T1 software comes with the following new parameters Parameter Descriptions Option Description Sigproto Tniclock SET T-1 Parameters Example Ds0=2 loopstart Ds0=11 CSMIM-T1 Hardware Installation Guide Chapter Troubleshooting Procedures Status LEDs Description General Normal Mode CSMIM-T1 Diagnostics POWER-UP and Boot Procedures Normal Mode Error-Free Sequence ActivityAmber Normal Mode Error Sequence Setup Mode Error-Free Sequence SET UP Mode Setup Mode Error States Boot Failures Boot Error Report Errors CSMIM-T1 sensed a hardware error during message Error Description See Table ErrorDescription Correcting CSMIM-T1 Parameters Unix Host on the LAN Load Server Host Not Responding Another CSMIM-T1 VAX VMS Load Host on the LAN Activity Green Amber CSMIM-T1 Dumps Network SystemAddress Filename Pathname Chapter Modem Guide Features Using the AT Command SET Title Default Key AT Command Factory Defaults Establishing 11-Bit Data Connections 3 V.32bis Cellular Connections Using AT Commands Universal Cellular SetupMNP 10 V.32bis Quick Connect Cellular Only Setup Modulation Protocols V.32bis Protocols Bell 212A protocol is for 1200 bps full-duplex connections Protocol Issue %G0 Issue %G1 Protocol Conﬁguration Command Settings Speed and Protocol Connection Matrices Modem Speed and Protocol Combinations For operations at V.22 600 bps, both modems must be set to Error Correction Error Correction Diagnostics Power-Up DiagnosticsLocal Analog Loopback with Self-Test Remote Digital Loopback with Self-Test Local Analog Loopback Local Digital Loopback Remote Digital Loopback Automatically Terminating a Test Register S18 Respond to Remote Digital Loopback Result Codes Connection Result Code TablesShort Form Long Form ATV1-M0W0 or ATV1-M0W1 Report DTE Speed Result Codes Report Modulation Speed ATV1-M0W2 ATV0W0 or ATV0W1 Report DTE speed ATV0W2 Report Modulation Speed Entering Commands Command SET Issuing AT Commands at any Speed Repeat Last CommandAnswer Bn ITU-T/Bell Mode An Auto-Reliable Fallback Character\An Maximum MNP Block Size Bn Modem-Port Bps Rate \Bn Transmit BreakCompression Control @Cn CTS, DSR, and DCD Connect Message Control Cn Serial-Port DCD Control \C0 \Cn Auto-Reliable Buffer Dial modifiers allow you to add conditions to the telephone H2 commandATD 011225551234 Enter Dial Modifiers ATD 9,,5551234 Enter Operating Mode Dial Modiﬁers This bong signal. Once it detects it, the modem continuesFirst, the modem hangs up and displays no Prompt Tone Dn Disconnect Buffer Delay DL Redial the Last Telephone Number DialedRedials the last telephone number that the modem dialed \D0 DTR ControlRepeat Dial \Dn Serial-Port DSR/CTS Control DCD Result Command Echo En Auto-RetrainEnModem-Port Data Length Mode En Compromise Equalizer\En Data Echo \E0 Guard Tone Restore Factory DefaultsSecondary Flow Control Independent Serial-Port/Modem-Port Speed \Gn Modem-Port Flow Control \G0Hang Up Identification Detect Phase\Jn Bps Rate Adjust Link Negotiation Speed \Kn Break Control KnMNP Extended Services 2illustrates the \Kn command Provides partial speed matching Enables speed matchingDisables speed matching Speed Matching Mode Setting on Originating Modem Bell212A Bell103 Modem Mode Mode Setting Answer Modem Originating Possible Connection Speed bps Modulation SelectionAllows connections through V.32bis Allows connections through V.FC MnMNP Class Connect Messages Mn Power Level Adjustment For Cellular Telephone Connections \N n Operating Mode Sets auto-reliable mode\N3 CSMIM-T1 Hardware Installation Guide On Enter Connect State On V.23 Equalizer Control OnSerial-Port ParityAT-O4D12345 Enter PnCheck Parity Pulse Dial \Q3 QuietFallback Modulation Speeds \Qn Serial-Port Flow Control Your computer to resume transmitting data to the modem During direct mode connections, the modem does not use flowControl and ignores the \Q setting Modem continues to send out the characters and empty Sn DSR Options Sn? Read Configuration RegistersRead All Registers RTS/CTS Options Tn Test and Diagnostics Commands Read Online StatusTone Dial Clear Serial-Port Speed \Tn Inactivity Timer \Vn Error Correction Result Code Form Vn Result Code FormDisplay Modem Firmware Version Connection Speed Reporting Display Bootstrap Revision Wn Pulse Digit Command Wn Store Current ConfigurationWn Store Complete Configuration Xn Extended Result Codes \Xn XON/XOFF Pass-Through \X0Yn Long Space Disconnect Zn Reset Yn Designate Default User Profile Commands to Change or Read Registers Displays the contents of all T n= n commands in decimalRegisters S3=n Carriage Return Character Range 0 255, Ascii decimal Default 43 +S1=n Ring Counter S2=n Escape Code Character S7=n Wait for Carrier After Dial S4=n Line Feed CharacterS5=n Backspace Character S6=n Wait Before Dialing S8=n Pause Time for Dial Delay S10=n Delay for Hang Up After Carrier LossS9=n Carrier Detect Response Time S11=n Dtmf Tone Dialing Speed S12=n Escape Code Guard TimeS14=n Bit Mapped Register Bit Function Decimal Value Position S16=n Bit Mapped Register, Test Options S18=n Test Timer S22=n Bit Mapped Register Table S21=n Bit Mapped Register Table S23=n Bit Mapped Register Table S27=n Bit Mapped Register Table S25=n Delay to DTR and Asynchronous Time Delay T3=n Timer for V.21 and V.23 Answer Tone Duration T2=n Timer for V.21 Mode During Multi-Protocol Answer T4=n Timer for Line Turnaround Delay Carrier On T5=n Timer for V.23 Half-Duplex Intercharacter DelayT6=n Timer for DCD Turn On Delay T7=n Timer for False Answer Abort T9=n Primary XON Flow Control CharacterT10=n Primary Xoff Flow Control Character T15=n V.24 Control Register T14=n Connect Message Delay TimerT11=n Secondary XON Flow Control Character T12=n Secondary Xoff Flow Control Character T16=n CTS Turn On Delay Timer T17=n V.32/V.32bis Connection Training TimerBit Function Position T22=n DSR Timer T19=n Bit Mapped RegisterT23=n Bit Mapped Register Table T42=n V.34/V.FC Connection Speed Selection T26=n Bit Mapped Register Table CSMIM-T1 Hardware Installation Guide Console Port Appendix a Port PIN/SIGNAL Allocations Interface Ports DCE Cabletron part number 9372075 for DB25 male Additional Cabletron Cables and Connectors CSMIM-T1 Hardware Installation Guide Numerics Symbols INDEX-2 INDEX-3 INDEX-4 INDEX-5 INDEX-6 INDEX-7 INDEX-8 INDEX-9 INDEX-10