Chapter 6

6-7

<Probable fault location>
Ink tank, ink tank unit, or main controller PCB
<Countermeasure>
1) Replace the ink tank.
2) Replace the ink tank unit.
3) Replace the main controller PCB.

6.1.3.20 03810204-2580/03810201-2581/03810202-2582/03810203-2583/03810212-2584/03810213-2585/03810206-2586/

03810205-2588/03810215-2589/03810207-258A/03810209-258B/03810208-258C Ink low error (occures when cleaning B

is executed)

0013-7175
<Cause>
Cleaning B was executed when the levels of remaining ink was level one.
<Probable fault location>
Ink tank, ink tank unit, or main controller PCB
<Countermeasure>
1) Replace the ink tank.
2) Replace the ink tank unit.
3) Replace the main controller PCB.

6.1.3.21 03810204-2590/03810201-2591/03810202-2592/03810203-2593/03810212-2594/03810213-2595/03810206-2596/

03810205-2598/03810215-2599/03810207-259A/03810209-259B/03810208-259C Ink low error (occures when printing)

0013-7176
<Cause>
Ink level low was detected when printing.
<Probable fault location>
Ink tank, ink tank unit, or main controller PCB
<Countermeasure>
1) Replace the ink tank.
2) Replace the ink tank unit.
3) Replace the main controller PCB.

6.1.3.22 03800301-2801/03800201-2802/03800401-2803/03800201-2812/03800302-2809/03800202-280A/03800402-280B/

03800202-2813 Printhead error

0013-7177
<Cause>
Improper installation of the printhead R was detected.
A checksum error was detected in the EEPROM of the printhead R.
Printhead R DI correction failed.
The version of printhead R was different.
Improper installation of the printhead L was detected.
A checksum error was detected in the EEPROM of the printhead L.
Printhead L DI correction failed.
The version of printhead L was different.
<Probable fault location>
Printhead, head relay PCB, carriage relay PCB, or main controller PCB
<Countermeasure>
1) Replace the printhead.
2) Cable continuity check
If continuity of the cable between the head relay PCB and the carriage relay PCB is abnormal, replace the cable.
3) Replace the Head relay PCB.
4) Cable continuity check
If continuity of the cable between the carriage relay PCB and the main controller PCB is abnormal, replace the cable.
5) Replace the carriage relay PCB.
6) Replace the main controller PCB.

6.1.3.23 03800101-2800/03800102-2808/03800201-2804/03800202-2807 Printhead installing error

0014-2756
<Cause>
Printhead R was not installed.
Printhead L was not installed.
Printhead R was installed to the left side.
Printhead L was installed to the right side.
<Probable fault location>
Operation method, printhead, head relay PCB, carriage relay PCB, or main controller PCB
<Countermeasure>
1) Operation check
Install the printhead properly.
2) Replace the printhead.
3) Cable continuity check
If continuity of the cable between the head relay PCB and the carriage relay PCB is abnormal, replace the cable.
4) Replace the Head relay PCB.
5) Cable continuity check
If continuity of the cable between the carriage relay PCB and the main controller PCB is abnormal, replace the cable.
6) Replace the carriage relay PCB.
7) Replace the main controller PCB.