Manuals / Brands / Power Tools / Router / Cisco Systems / Power Tools / Router

Cisco Systems 9001, 9001S, ASR9001, ASR9001s Safety Guidelines

1 114

Download 114 pages, 13.62 Mb

1-2

Cisco ASR 9001 and Cisco ASR 9001-S Routers Hardware Installation Guide

OL-26701-02

Chapter 1 Preparing for Installation

Safety Guidelines

Figure 1-2 Front Panel of the Cisco ASR 9001-S Router

In order to achieve the full bandwidth of 120 Gbps and to enable the disabled ports, a Cisco license can

be obtained. Once the license is obtained and installed, the Cisco ASR 9001-S Router must be reloaded

to bring up the full 120 Gbps capacity. For information on configuring the Cisco license for

Cisco ASR 9001-S Router, refer to the Cisco ASR 9001-S 120G Upgrade License Configuration Guide.

Note The Cisco ASR 9001-S Router follows the same hardware installation procedure as the procedure for the

Cisco ASR 9001 Router, described in this document.

This chapter guides you through the process of preparing for router installation.

Before installing your Cisco ASR 9001 Router, you must consider these requirements:

•power and cabling requirements must be in place at your installation site

•special equipments must be available for installing the router

•the environmental conditions that your installation site must meet to maintain normal operation

The shipping package for the router is engineered to reduce chances of product damage that may result

from routine material handling during shipment:

•Keep the router in the shipping container until you have determined the installation site.

•The router should always be transported or stored in its shipping package in the upright position.

Inspect all items for shipping damage. If an item appears damaged, contact a Cisco customer service

representative immediately.

This chapter contains these installation topics:

•Safety Guidelines, page 1-2

•Site Requirement Guidelines, page 1-5

•Cisco ASR 9001 Router Port Connection Guidelines, page 1-21

Safety Guidelines

Before you perform any procedure in this publication, you must review the safety guidelines in this

section to avoid injuring yourself or damaging the equipment.

Note that this section contains guidelines, and do not include every potentially hazardous situation.

When you install a router, always use caution and common sense.

General Safety Guidelines

•Never attempt to lift an object that might be too heavy for you to lift by yourself.

360032

Contents

Main Page CONTENTS Cisco ASR 9001 Router 1 Cisco ASR 9001-S Router 1 Page Page Page Preface Changes to This Document Audience Purpose Document Organization Document Conventions Obtaining Documentation and Submitting a Service Request Page Preparing for Installation Cisco ASR 9001 Router Cisco ASR 9001-S Router Safety Guidelines General Safety Guidelines Compliance and Safety Information Laser Safety Energy Hazard Preventing Electrostatic Discharge Damage Lifting Guidelines Site Requirement Guidelines Site Layout and Equipment Dimensions Rear of chassis Front of chassis Site Wiring Guidelines Chassis Air Flow Guidelines Rack-Mounting and Air Flow Clearance Guidelines Room air Air exhaust Telco 2-Post Rack Open 4-Post Rack Enclosed Rack with Perforated Sides Air Flow Guidelines for Enclosed Rack Installation Temperature and Humidity Guidelines Power Connection Guidelines AC Powered Routers AC Power Cord Illustrations 1-14 Figure 1-9 AC Power Cord CAB-AC Figure 1-11 AC Power Cord CAB-ACA Figure 1-10 AC Power Cord CAB-L620P-C13-JPN 1-15 Figure 1-12 AC Power Cord CAB-ACI Figure 1-13 AC Power Cord CAB-ACR Figure 1-14 AC Power Cord CAB-ACS 1-16 DC Powered Router 1-18 Figure 1-20 shows the type of terminal block required for DC-input cable connections. Figure 1-21 shows DC power source cable connections for single DC power module. Page NEBS Supplemental Unit Bonding and Grounding Guidelines Cisco ASR 9001 Router Port Connection Guidelines 92 1 3 4 5 6 687 Page Console Port and Auxiliary Port Connection Guidelines Console Port Signals Auxiliary Port Signals Management LAN Ports Connection Guidelines Management LAN Port LED Indicators Management LAN RJ-45 Cabling Sync Ports Connection Guidelines SYNC Port LED Indicators RP External USB Port Page Unpacking and Installing the Chassis Pre-Installation Considerations and Requirements Installation Overview Required Tools and Equipment Unpacking the Cisco ASR 9001 Router Positioning the Router Rack-Mounting the Router Chassis Verifying Rack Dimensions Installing the Chassis in a 2-Post Rack Page Page Installing the Chassis in a 4-post Rack Supplemental Bonding and Grounding Connections Page Installing Modules and Cables in the Chassis Fixed 4x10-Gigabit Ethernet Ports Modular Port Adapters 20-Port Gigabit Ethernet Modular Port Adapter 92 1 3 4 5 6 687 4-Port 10 Gigabit Ethernet Modular Port Adapter 2-Port 10 Gigabit Ethernet Modular Port Adapter Installing and Removing Modular Port Adapters Handling Modular Port Adapters (MPAs) Online Insertion and Removal Modular Port Adapter (MPA) Installation and Removal Optical Device Installation and Removal Cleaning Optical Devices Checking the Installation Verifying the Installation Using show Commands to Verify Modular Port Adapter (MPA) Status Using show Commands to Display Modular Port Adapter (MPA) Information Using the ping Command to Verify Network Connectivity Installing and Removing SFP Modules Installing and Removing XFP Modules Cable Management Cable Management Tray Installing a Cable Management Tray Removing a Cable-Management Tray Cable Management Bracket Installing a Cable Management Bracket Removing a Cable-Management Bracket Connecting Route Processor Cables Connecting to the RP Console Port Connecting to the RP Auxiliary Port Connecting to the RP Ethernet Management Ports Connecting Power to the Router Connecting Power to an AC-Powered Router Page Connecting Power to a DC-Powered Router Powering on the Router Page Troubleshooting the Installation Troubleshooting Overview Troubleshooting Using a Subsystem Approach Normal Router Startup Sequence Identifying Startup Issues Troubleshooting the Power Subsystem Troubleshooting the AC-Input Power Subsystem Page Troubleshooting the DC-Input Power Subsystem Troubleshooting a DC Power Module Additional Power Subsystem Troubleshooting Information Hardware and Software Identification Obtaining Temperature and Environmental Information 4-7 Troubleshooting the Power Distribution System Troubleshooting the Route Processor Subsystem Route Processor Overview 92 1 3 4 5 6 687 RP Front Panel Indicators FAIL/OK (Power Module) Ethernet Ports and Status LEDs Auxiliary and Console Ports STATUS (Fan tray) Monitoring Critical, Major, and Minor Alarm Status Troubleshooting the Line Card Initial Boot Process Status LEDs Configuring and Troubleshooting Line Card Interfaces Configuration Parameters Line Card Interface Address Using Configuration Commands Basic Line Card Configuration Verifying the Transceiver Modules 4-16 Advanced Line Card Troubleshooting Troubleshooting the Cooling Subsystem Fan Tray Operation Power Module Fans Over-temperature Conditions Isolating Cooling Subsystem Problems Page Replacing Cisco ASR 9001 Router Components Prerequisites and Preparation Field Replaceable Units Online Insertion and Removal Powering Off the Router Removing and Replacing the Fan Tray Removing and Replacing AC or DC Power System Components Power Module Replacement Guidelines Removing and Replacing an AC or DC Power Module Removing an AC or DC Power Module Installing an AC or DC Power Module Removing a Chassis from the Equipment Rack Installing a Replacement Chassis in the Equipment Rack Packing a Chassis for Shipment APPENDIX A Technical Specifications Page Page Page Page Page Page Page Page Page APPENDIX B Site Log Page INDEX Numerics A B C Page D E F G H I L M N O P R S T U V W X