Guide, Release Modification | Cisco Systems NME-16ES-1G instruction

Cisco EtherSwitch Service Modules Feature

Guide

Note This document describes the Cisco EtherSwitch service module only. For information about the Cisco Ethernet switch network module, see “Connecting Ethernet Switch Network Modules to a Network” at the following URL: http://www.cisco.com/en/US/products/hw/modules/ps2797/products_module_installation_guide_chapt er09186a00800b168c.html

The Cisco EtherSwitch service modules (NME-16ES-1G, NME-16ES-1G-P, NME-X-23ES-1G, NME-X-23ES-1G-P, NME-XD-48ES-2S-P, and NME-XD-24ES-1S-P) provide Cisco modular access routers the ability to stack Cisco EtherSwitch service modules as Layer 2 switches using Cisco StackWise technology. The Cisco EtherSwitch service modules are supported by either the IP base image (formerly known as standard multilayer image [SMI]) or the IP services image (formerly known as the enhanced multilayer image [EMI]). The IP base image provides Layer 2+ features, including access control lists (ACLs), quality of service (QoS), static routing, and the Routing Information Protocol (RIP). The IP services image provides a richer set of enterprise-class features, including Layer 2+ features and full Layer 3 routing (IP unicast routing, IP multicast routing, and fallback bridging). To distinguish it from the Layer 2+ static routing and RIP, the IP services image includes protocols such as the Enhanced Interior Gateway Routing Protocol (EIGRP) and the Open Shortest Path First (OSPF) Protocol.

Feature History for the Cisco EtherSwitch Service Modules (NME-16ES-1G-P, NME-X-23ES-1G-P,

NME-XD-24ES-1S-P, NME-XD-48ES-2S-P)

Release	Modification
12.2(25)EZ (switch software)	This feature was introduced.

12.3(14)T (router software)	This feature was introduced.

Feature History for the Cisco EtherSwitch Service Modules (NME-16ES-1G, NME-X-23ES-1G)

Release	Modification
12.2(25)SEC (switch software)	This feature was introduced.

12.3(14)T3 (router software)	This feature was introduced.

Corporate Headquarters:

Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA

Copyright © 2005 Cisco Systems, Inc. All rights reserved.

Image 1

Cisco Systems NME-16ES-1G manual Guide, Release Modification

Contents

Release Modification Guide Contents Hardware Overview Network Modules Hardware Installation Guide Software Features and Benefits Performance Features Ease-of-Use and Ease-of-Deployment Features Management Options Availability Features Manageability Features Vlan Features Security Features QoS and CoS Features Monitoring Features Power-over-Ethernet Features Cisco StackWise Concepts Overview of Switch Stacks Switch Stack Membership Stack Master Election and Re-Election Stack Member Numbers Switch Stack Bridge ID and Router MAC Address Stack Member Priority Values Stack Protocol Version Compatibility Switch Stack Software Compatibility Recommendations Switch Stack Configuration Files Switch Stack Management Connectivity Clustering Concepts Accessing the CLI of a Specific Stack MemberManagement Connectivity to Specific Stack Members Standby Command Device Characteristics Command Device CharacteristicsCluster Compatibility Automatic Discovery of Candidates and Members Candidate and Member CharacteristicsDiscovery of Candidates and Members Through CDP Hops Vlan Discovery of Candidates and Members Through Different VLANs Discovery of Candidates and Members Through Routed Ports Switch New out-of-box Discovery of Newly Installed Switches in Clusters Hsrp and Standby Cluster Command Switches Other Considerations for Cluster Standby Groups Virtual IP Addresses in Clusters Automatic Recovery of Cluster Configuration Hostnames in Clusters IP Addresses in Clusters Switch Clusters and Switch Stacks Passwords in ClustersSwitch Stack Switch Cluster Snmp Community Strings in Clusters Switch Stack Switch Cluster TACACS+ and Radius in Clusters Availability of Switch-Specific Features in Switch Clusters Cisco IOS Release 12.225SEC Using Interface Configuration Mode Boot flash image-name Command or Action PurposeExample Dir flash Show running configuration EnableConfigure terminal Service-module interface slot/port session Output of the show service-module status command Show power inlineShow ip interface brief Control+shift+6 Sample Output for the boot flash Command on the Router Sample Output for the dir flash Command on the RouterRouter boot flashc2800-adventerprisek9-mz Examples Router# configure terminal Router# show running config interface gigabitethernet2/0Router# service-module gigabitethernet2/0 session Switch dir flash Switch# ctrl+shift+6 Switch# show ip interface briefSwitch# show power inline Sample Output for Pressing Ctrl+Shift+6 Followed by Dhcp Feature Default Setting STP Prerequisites Clustering Concepts section on Return Sample Output for Assigning the IP Address and Subnet Mask Sample Output for Entering an Interface Name Command or Action Purpose Sample Output for Saving the Configuration to Nvram Router# service-module gigabitethernet1/0 reset Router# service-module gigabitethernet1/0 shutdownRouter# service-module gigabitethernet1/0 reload Cisco IOS Release 12.225SEC Restrictions Default Switch Stack Configuration Assigning a Stack Member Number Sample Output for the reload slot Command Sample Output for the switch renumber CommandShow switch Switchconfig# switch 6 renumber Sample Output for the show switch Command Setting the Stack Member Priority Value Sample Output for the switch priority Command Verifying Information About the Switch StackSwitchconfig# switch 2 priority Switch show switch Switch# show platform stack-manager all Show switch stack-ports Switchconfig# show switch neighbors Rcommand Using the CLI to Manage Switch ClustersShow version Sample Output for the show cluster members Command Sample Output for the rcommand and show version Commands Choose View Refresh Choose Cluster Add to Cluster or Cluster member Password Detailed Steps from the CLI Creating a Cluster Standby Group Routing-redundancy Cluster standby-group HSRP-group-name No switchport Sample Output for the ping tftpserver Command Sample Output for the copy tftp flash Command Sample Output for the show flash CommandSwitch# show flash Switch# copy tftp flash Service-module interface slot/port password-reset Flashinit Recovering from a Corrupted Software Image Using Xmodem Password-reset Service-module interface slot/portFlashinit Control+6 Sample Output for the copy flash xmodem Command TroubleshootingRouter# copy flash xmodem Router# copy tftp xmodem Sample Output for the copy tftp xmodem Command Router# service-module gigabitethernet2/0 password-reset Router# service-module gigabitethernet1/0 session Recovering from a Lost or Forgotten Password Optional loadhelper filesystem/file-url Enable secret password Boot -x -v deviceimagenameRename Copy flash Reload Copy running-configuration startup-configuration Optional set Boot Service-module password-reset command Example Sample Output for the set CommandSet Scenario Action Result Current-stack-member-number Renumber new-stack-member-number Network Configuration Examples Network Demands Suggested Design Methods Cost-Effective Wiring Closet Redundant Gigabit Backbone Cisco SoftPhone Software Gigabit servers POP Technical Assistance Related DocumentsRelated Topic Document Title Description Link