Cisco Systems NME-16ES-1G - page 49

Cisco EtherSwitch Service Modules Feature Guide

How to Configure the Cisco EtherSwitch Service Module

49

Cisco IOS Release 12.2(25)SEC

Examples

This section provides the following examples:

•Sample Output for the service-module gigabitethernet shutdown Command, page 49

•Sample Output for the service-module gigabitethernet reset Command, page49

•Sample Output for the service-module gigabitethernet reload Command, page49

Sample Output for the service-module gigabitethernet shutdown Command

The following example shows what appears when you enter the service-module gigabitethernet

slot/unit shutdown command:

Router# service-module gigabitethernet1/0 shutdown

Shutdown is used for Online removal of Service Module.

Do you want to proceed with shutdown?[confirm]

Use service-module reset command to recover from shutdown.

Note At the confirmation prompt, press Enter to confirm the action or n to cancel.

Sample Output for the service-module gigabitethernet reset Command

The following example shows what appears when you enter the service-module gigabitethernet

slot/unit reset command:

Router# service-module gigabitethernet1/0 reset

Use reset only to recover from shutdown or failed state

Do you want to reset?[confirm]

Note At the confirmation prompt, press Enter to confirm the action or n to cancel.

Sample Output for the service-module gigabitethernet reload Command

The following example shows what appears when you enter the service-module gigabitethernet

slot/unit reload command:

Router# service-module gigabitethernet1/0 reload

Do you want to proceed with reload?[confirm]

Note At the confirmation prompt, press Enter to confirm the action or n to cancel.

Step2 service-module gigabitethernet slot/unit reset

Example:

Router# service-module gigabitethernet1/0 reset

Performs a hardware reset of the Cisco EtherSwitch service

module.

Step3 service-module gigabitethernet slot/unit reload

Example:

Router# service-module gigabitethernet1/0

reload

Performs a graceful halt and reload of the Cisco

EtherSwitch service module operating system.

Command or Action Purpose

Contents

Main Cisco EtherSwitch Service Modules Feature Guide Contents Prerequisites for the Cisco EtherSwitch Service Modules Information About the Cisco EtherSwitch Service Modules Hardware Overview Software Features and Benefits Ease-of-Use and Ease-of-Deployment Features Performance Features Management Options Manageability Features Availability Features VLAN Features Security Features QoS and CoS Features Power-over-Ethernet Features Monitoring Features Cisco StackWise Concepts Overview of Switch Stacks Switch Stack Membership Stack Master Election and Re-Election Switch Stack Bridge ID and Router MAC Address Stack Member Numbers Stack Member Priority Values Switch Stack Software Compatibility Recommendations Stack Protocol Version Compatibility Major Incompatibility Between Cisco EtherSwitch Service Modules Minor Incompatibility Between Cisco EtherSwitch Service Modules Switch Stack Configuration Files Switch Stack Management Connectivity Management Connectivity to the Switch Stack Through an IP Address Management Connectivity to the Switch Stack Through an SSH Session Management Connectivity to the Switch Stack Through Console Ports Management Connectivity to Specific Stack Members Clustering Concepts Cluster Compatibility Command Device Characteristics Standby Command Device Characteristics Candidate and Member Characteristics Automatic Discovery of Candidates and Members Discovery of Candidates and Members Through CDP Hops Discovery of Candidates and Members Through Non-CDP-Capable and Noncluster-Capable Devices Discovery of Candidates and Members Through Different VLANs Discovery of Candidates and Members Through Different Management VLANs switch 7 Discovery of Candidates and Members Through Routed Ports Discovery of Newly Installed Switches in Clusters HSRP and Standby Cluster Command Switches Virtual IP Addresses in Clusters Other Considerations for Cluster Standby Groups Automatic Recovery of Cluster Configuration IP Addresses in Clusters Hostnames in Clusters Passwords in Clusters SNMP Community Strings in Clusters Switch Clusters and Switch Stacks Page TACACS+ and RADIUS in Clusters Availability of Switch-Specific Features in Switch Clusters How to Configure the Cisco EtherSwitch Service Module Accessing the CLI Through a Console Connection or Through Telnet Understanding Interface Types on the Cisco EtherSwitch Service Modules Using Interface Configuration Mode Configuring the Cisco EtherSwitch Service Module in the Router Page Page Page Sample Output for the show running config Command on the Router The following example shows what appears when you enter the show running config command: Sample Output for Configuring the Cisco EtherSwitch Service Module Interface on the Router Sample Output for the service-module Command on the Cisco EtherSwitch Service Module The following example shows what appears when you enter the service module command: Sample Output for the dir flash: Command on the Cisco EtherSwitch Service Module The following example shows what appears when you enter the show ip interface brief command: Sample Output for Pressing <Ctrl+Shift+6> Followed by x The following example shows what appears when you press <Ctrl+Shift+6> and then press x: Sample Output for the show power inline Command on the Router Sample Output for the show power inline Command on the Cisco EtherSwitch service module Default Settings After Initial Cisco EtherSwitch Service Module Configuration Page Configuring the Cisco EtherSwitch Service Module Using the Switch Setup Program Page Page Sample Output for Entering an Interface Name The following example shows what appears when you enter an interface name: Sample Output for Assigning the IP Address and Subnet Mask Sample Output for Configuring the Cisco EtherSwitch Service Module as a Standalone Service Module Shutting Down, Resetting, and Reloading the Cisco EtherSwitch Service Module Page How to Configure the Cisco EtherSwitch Service Module in a Switch Stack Default Switch Stack Configuration Assigning a Stack Member Number Page Setting the Stack Member Priority Value Verifying Information About the Switch Stack Step 1 Use the show platform stack-manager command to display platform-dependent switch-stack neighbors of a switch stack: stack. Use the show switch neighbors user EXEC command to display detailed information about the How to Configure a Switch Cluster Using the CLI to Manage Switch Clusters Page Adding Cluster Members to the Cisco EtherSwitch Service Module DETAILED STEPS FROM THE NETWORK ASSISTANT APPLICATION DETAILED STEPS FROM THE CLI Creating a Cluster Standby Group Upgrading the Cisco EtherSwitch Service Module Software Page Page Troubleshooting the Cisco EtherSwitch Service Module Software Recovering from a Corrupted Software Image Using Xmodem Page Troubleshooting Examples Page You are prompted for the max retry count. Accept the default: You are prompted to confirm the transfer to the Cisco EtherSwitch service module: The following appears when the image is downloaded to the service module: Sample Output for the service-module session Command on the Cisco EtherSwitch Service Module The following example shows what appears when you enter the service-module session command: Recovering from a Lost or Forgotten Password Page Page Page Recovering from a Lost or Forgotten Password When Password Recovery Is Disabled Page Example Switch Stack Configuration Scenarios Page Page Network Configuration Examples Network Design Concepts for Using the Cisco EtherSwitch Service Module Page Page Page Multidwelling Network Using the Cisco EtherSwitch Service Modules Page Additional References Related Documents Technical Assistance